HORIZON FITNESS 5.0 IC Indoor Cycle Owner’s Manual
- June 12, 2024
- HORIZON FITNESS
Table of Contents
HORIZON FITNESS 5.0 IC Indoor Cycle Owner’s Manual
ASSEMBLY
WARNING
There are several areas during the assembly process that special attention must be paid. It is very important to follow the assembly instructions correctly and to make sure all parts are firmly tightened. If the assembly instructions are not followed correctly, the indoor cycle could have parts that are not tightened and will seem loose and may cause irritating noises. To prevent damage to the indoor cycle, the assembly instructions must be reviewed and corrective actions should be taken.
Before proceeding, find your indoor cycle’s serial number located on the front stabilizer of the cycle and enter it in the space provided below.
ENTER YOUR SERIAL NUMBER IN THE BOX BELOW:
» Refer to the SERIAL NUMBER and MODEL NAME when calling for service.
» Be sure to enter both the SERIAL NUMBER and MODEL NAME on your warranty
card.
MODEL INFORMATION
MAIN PARTS INCLUDED:
- Main Frame (20)
- Front Stabilizer (21F)
- Rear Stabilizer (21R)
- Handlebar Set (22)
- Handlebar Post (23)
- Console (29)
- Pedal Set (34 L&R)
- Seat Post Set (31, 32 & 33)
HARDWARE KIT:
PRE ASSEMBLY
UNPACKING
Due to the weight of the indoor cycle, it is recommended that two people
perform the assembly. Unpack the product where you will be using it. It is
recommended that you place a protective covering on your floor. Place the
carton on a level flat surface and remove all packing materials; do not
dispose of the packing materials until assembly is completed.
NOTE: During each assembly step, ensure that ALL nuts and bolts are in place and partially threaded in before completely tightening any ONE bolt.
NOTE: A light application of grease may aid in the installation of hardware. Any grease, such as lithium bike grease is recommended.
NEED HELP?
If you have questions or if there are any missing parts, contact Customer Tech Support.
ASSEMBLY
STEP 1
ASSEMBLY STEP 2
ASSEMBLY STEP 3
3.1 Turn Adjustment Knob (24) counter-clockwise to fully loosen.
3.2 Attach Lead Wire (26) to Console Cable (25) and pull Console Cable (25)
from Head Tube (28) through Handlebar Post (23) and out hole in front of
Handlebar Post (23).
3.3 Pull Console Cable (25) through hole in Console Bracket (27).
3.4 Insert Handlebar Post (23) into Head Tube (28) and turn Adjustment Knob
(24) to secure.
3.5 Detach and discard Lead Wire (26).
NOTE: Be careful not to pinch any wires while assembling handlebars.
ASSEMBLY STEP 4
NOTE: Be careful not to pinch any wires while assembling console.
ASSEMBLY STEP 5
ASSEMBLY STEP 6
CONGRATULATIONS!
You have successfully assembled your indoor cycle.
INDOOR CYCLE OPERATION
RESISTANCE CONTROL AND EMERGENCY BRAKE
The preferred level of difficulty in pedaling (resistance) can be regulated in
increments by use of the resistance buttons on the console. To increase the
resistance, push the up arrow. To decrease the resistance, push the down
arrow.
FOR INDOOR CYCLE:
WARNING
- Make sure your shoes are fixed into the toe cage (if available).
- Apply full resistance load when the Indoor Cycle is not in use to prevent injuries due to moving drive gear components.
- The Indoor Cycle does not have a free moving flywheel; the pedals will continue to move together with the flywheel until the flywheel stops. Reducing speed in a controlled manner is required. To stop the flywheel immediately, push down hard the emergency brake. Always pedal in a controlled manner and adjust your desired cadence according to your own abilities. Push the emergency brake down = emergency stop.
- The Indoor Cycle uses a fixed flywheel that builds momentum and will keep the pedals turning even after the user stops pedaling or if the user’s feet slip off. DO NOT ATTEMPT TO REMOVE YOUR FEET FROM THE PEDALS OR DISMOUNT THE MACHINE UNTIL BOTH THE PEDALS AND THE FLYWHEEL HAVE COMPLETELY STOPPED. Failure to follow these instructions may lead to loss of control and the potential for serious injury.
INDOOR CYCLE SEAT & HANDELBAR ADJUSTMENT (IF AVAILABLE)
Rotate the adjustment lever or knob counterclockwise to slide the seat or
handlebars forward or backward for horizontal adjustment; raising or lowering
the seat or handlebar with the other hand for height adjustment. Rotate the
lever or knob clockwise to lock the position. Do not adjust seat or handlebar
height past MAX mark or adjustment points on post.
CONSOLE
CONSOLE DISPLAY
CONSOLE OPERATION
HOW TO SWITCH BETWEEN APP MODE & BT HEART RATE MODE
Read More About This Manual & Download PDF:
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>