PACIFIC ENERGY T4 LE Alderlea Wood Stove Instruction Manual

June 16, 2024
Pacific Energy

T4 LE Alderlea Wood Stove

Product Information

Specifications

  • Model: ALDERLEA T4 LE
  • Tested and Listed to: CAN/ULC S627 and UL 1482
  • Serial #: 180923-28
  • ALT4-LE: 100003978
  • Meets the U.S. Environmental Protection Agency’s 2020
    Particulate Emission Standards (Crib Wood)

Safety Notice

If this stove is not properly installed, a house fire may
result. For your safety, follow the installation instructions.
Contact local building or fire officials about restrictions and
installation inspection requirements in your area.

Operating and Installation Instructions

Baffle / Tube Removal

To remove the baffle/tube:

  1. Refer to the manual on www.pacificenergy.net for specific
    instructions.

Tube / Baffle Board Removal

To remove the tube/baffle board:

  1. Refer to the manual on www.pacificenergy.net for specific
    instructions.

Installation

To install the stove:

  1. Refer to the manual on www.pacificenergy.net for specific
    instructions.

Assembly

To assemble the stove:

  1. Refer to the manual on www.pacificenergy.net for specific
    instructions.

Dimensions

The dimensions of the stove are:

  • Refer to the manual on www.pacificenergy.net for specific
    dimensions.

Floor Protector

A floor protector is required for installation. Please refer to
the manual on www.pacificenergy.net for specific requirements.

Residential Installation

For residential installation:

  1. Refer to the manual on www.pacificenergy.net for specific
    instructions.

Usage Instructions

WARNING: Hot Glass

Hot glass will cause burns. Do not touch the glass until cooled.
Never allow children to touch the glass.

Chemical Exposure Warning

This product can expose you to chemicals including ceramic
fibers, which are known to the state of California to cause cancer,
and to carbon monoxide, which is known to the state of California
to cause birth defects or other reproductive harm. For more
information, go to www.p65warnings.ca.gov. This warning is
applicable to all PACIFIC ENERGY FIREPLACE PRODUCTS.

Smoke and Carbon Monoxide Detectors

We strongly recommend that smoke and carbon monoxide detectors
be installed in the area where the heater is to be installed. If
smoke detectors have been previously installed, you may notice that
they are operating more frequently. This may be due to curing of
stove paint or fumes caused by accidentally leaving the fire door
open. Do not disconnect the detectors.

Read the Manual

Please read this entire manual before you install and use your
new room heater. Failure to follow instructions may result in
property damage, bodily injury, or even death.

Proper Combustion and Efficient Burning

Experience will give you the right settings for proper
combustion and efficient burning. Remember, the correct air inlet
setting is affected by variables such as type of wood, outside
temperature, chimney size, and weather conditions. With practice,
you will become proficient in operating your heater and will obtain
the performance for which it was designed.

FAQ (Frequently Asked Questions)

Q: What are the specifications of the stove?

A: The stove model is ALDERLEA T4 LE. It is tested and listed to
CAN/ULC S627 and UL 1482 standards. The serial number is 180923-28
and the ALT4-LE number is 100003978. It meets the U.S.
Environmental Protection Agency’s 2020 Particulate Emission
Standards (Crib Wood).

Q: What precautions should I take for safety?

A: It is important to properly install the stove to avoid a
house fire. Follow the installation instructions provided and
consult local building or fire officials for any restrictions or
inspection requirements in your area. Additionally, be cautious of
the hot glass as it can cause burns. Do not touch the glass until
cooled and keep children away from it.

Q: Are there any chemical exposure risks associated with this

product?

A: Yes, this product can expose you to chemicals including
ceramic fibers, known to cause cancer, and carbon monoxide, known
to cause birth defects or other reproductive harm. For more
information, visit www.p65warnings.ca.gov. This warning is
applicable to all PACIFIC ENERGY FIREPLACE PRODUCTS.

Q: Do I need to install smoke and carbon monoxide

detectors?

A: Yes, it is strongly recommended to install smoke and carbon
monoxide detectors in the area where the heater is installed. If
you notice the detectors operating more frequently, it may be due
to stove paint curing or fumes from accidentally leaving the fire
door open. Do not disconnect the detectors.

Q: How can I optimize the performance of my heater?

A: Proper combustion and efficient burning can be achieved
through experience and adjusting the air inlet setting based on
variables such as wood type, outside temperature, chimney size, and
weather conditions. With practice, you will become proficient in
operating your heater and optimize its performance.

IMPORTANT: THESE INSTRUCTIONS ARE TO REMAIN WITH THE HOMEOWNER
TESTED and LISTED to; CAN/ULC S627 AND UL 1482

SERIAL #

SAFETY NOTICE
If this stove is not properly installed, a house fire may result. For your safety, follow the installation instructions. Contact local building or fire officials about restrictions and installation inspection requirements in your area.

OPERATING AND INSTALLATION INSTRUCTIONS

MODEL:

Meets the U.S. Environmental Protection Agency’s 2020 Particulate Emission Standards (Crib Wood).

ALDERLEA T4 LE

Visit www.pacificenergy.net for the most recent version of this manual

180923-28

ALT4-LE

100003978

Table of Contents

Table of Contents ……………………………………………………………. 2 Rating Label …………………………………………………………………… 3
Efficiency and BTU Output…………………………………………. 3 Safety ……………………………………………………………………………. 4
Chimney Smoke and Creosote Formation……………………. 4 Chimney Fires ………………………………………………………….. 4 To Avoid a Chimney Fire…………………………………………….. 5 In the event of a Chimney Fire ……………………………………. 5 Curing of the Paint Finish…………………………………………… 5 Operation ……………………………………………………………………….. 6 Wood Selection ………………………………………………………… 6 DO NOT BURN :……………………………………………………….. 6 How to Test Your Wood……………………………………………… 6 Lighting a fire……………………………………………………………. 7 Normal Operation……………………………………………………… 7 Restarting After Extended or Overnight Burns ……………… 8 Proper Draft……………………………………………………………… 8 Ash Removal ……………………………………………………………. 8 Ash Clean out system: …………………………………………….. 8 Disposal of Ashes……………………………………………………… 8 Maintenance …………………………………………………………………… 9 Maintenance Checks ……………………………………………………… 10 Weekly:………………………………………………………………….. 10 Monthly …………………………………………………………………. 10 When Cleaning the Chimney System:………………………… 10 Blower: ………………………………………………………………….. 10 Baffle: ……………………………………………………………………. 10

Baffle / Tube Removal ……………………………………………………. 11 Tube / Baffle Board Removal ………………………………….. 11 Installation ……………………………………………………………… 11
Assembly ……………………………………………………………………… 12 Dimensions …………………………………………………………………… 12 Floor Protector ……………………………………………………………… 13 Residential Installation ……………………………………………………. 14
Clearances: ……………………………………………………………. 14 Chimney and Connector ………………………………………….. 15 When using a Double-Wall Connector ……………………….. 15 When using a Single-Wall (smoke pipe) Connector ……… 15 Combustion Air ……………………………………………………………… 16 Installation Procedure ……………………………………………… 16 Through Wall Installations (as per NFPA 211) …………….. 19 Mobile Home Installation ………………………………………………… 21 Trouble Shooting …………………………………………………………… 22 Optional Blower …………………………………………………………….. 23 Blower Operation ……………………………………………………. 23 Firebrick Installation ………………………………………………………. 23 Replacement Parts – Alderlea T4 LE ………………………………… 26

! WARNING
HOT GLASS WILL CAUSE BURNS.
DO NOT TOUCH GLASS UNTIL COOLED.
NEVER ALLOW CHILDREN TO TOUCH GLASS.

WARNING: this product can expose
you to chemicals including ceramic fibers, which are known to the state of California to cause cancer,and to carbon monoxide, which is known to the state of California to cause birth defects or other reproductive harm.
For more information go to www.p65warnings.ca.gov.
This warning is applicable to all PACIFIC ENERGY FIREPLACE PRODUCTS

PLEASE SAVE THESE INSTRUCTIONS
NOTE: WE STRONGLY RECOMMEND THAT SMOKE AND CARBON MONOXIDE DETECTORS BE INSTALLED IN THE AREA WHERE THE HEATER IS TO BE INSTALLED. If smoke detectors have been previously installed, you may notice that they are operating more frequently. This may be due to curing of stove paint or fumes caused by accidentally leaving the fire door open. Do not disconnect the detectors.
SAFETY NOTICE: If this stove is not properly installed, a house fire may result. For your safety, follow the installation instructions. Contact local building or fire officials about restrictions and installation inspection requirements in you area. Please read this entire manual before you install and use your new room heater. Failure to follow instructions may result in property damage, bodily injury, or even death.

Experience will give you the right settings for proper combustion and efficient burning. Remember the correct air inlet setting is affected by variables such as type of wood, outside temperature, chimney size and weather conditions. With practice, you will become proficient in operating your heater and will obtain the performance for which it was designed.

100003978

2

ALT 4-LE 180923-28

MUR ADJACENT ADJACENT WALL

COTE SIDE

Rating Label
PLEASE SAVE THESE INSTRUCTIONS
This manual describes the installation and operation of the; Pacific Energy, ALDERLEA T4 LE and ALDERLEA T4 LE Classic freestanding wood heater.
SAFETY NOTICE: If this stove is not properly installed, a house fire may result. For your safety, follow the installation instructions. Contact local building or fire officials about restrictions and installation inspection requirements in you area.
Please read this entire manual before you install and use your new room heater. Failure to follow instructions may result in property damage, bodily injury, or even death.

ALT 4-LE 180923-28

CERTIFIED FOR CANADA AND U.S.A. – MODEL / MODÈLE: VISTA LE VISTA CLASSIC LE ALDERLEA T4 LE

LISTED ROOM HEATER, SOLID FUEL TYPE. ALSO FOR USE IN MOBILE HOMES CERTIFIED TO / CERTIFIÉ POUR: CAN/ULC S627 / UL 1482

DO NOT REMOVE THIS LABEL

Refer to Intertek’s Directory of Building Products for detailed information

C#4001507
· FOR USE WITH SOLID FUEL (CORDWOOD ) ONLY. DO NOT USE OTHER FUEL TYPES. INSTALL AND USE IN ACCORDANCE WITH THE MANUFACTURER’S INSTALLATION AND OPERATING INSTRUCTIONS.
· CONTACT LOCAL BUILDING OR FIRE OFFICIALS ABOUT RESTRICTIONS, INSTALLATION PERMIT AND INSPECTION IN YOUR AREA.
S· DO NOT CONNECT THIS UNIT TO A CHIMNEY FLUE SERVING ANOTHER APPLIANCE.
· USE 6 INCH / 150MM DIAMETER MINIMUM 24 MSG BLACK OR LISTED CONNECTOR. · UNIT CAN BE CONNECTED TO A LINED MASONRY CHIMNEY SUITABLE FOR USE WITH SOLID FUELS.
A · DO NOT OBSTRUCT THE SPACE BENEATH THE HEATER. M · DO NOT ROUTE POWER CORD BENEATH HEATER.
· SEE LOCAL BUILDING CODE AND MANUFACTURER’S INSTRUCTIONS FOR PRECAUTIONS REQUIRED WHEN PASSING A CHIMNEY THROUGH A COMBUSTIBLE WALL OR CEILING.
· DO NOT PASS A CHIMNEY CONNECTOR THROUGH A COMBUSTIBLE WALL OR CEILING. · MINIMUM CLEARANCE BETWEEN SINGLE WALL CHIMNEY CONNECTOR AND COMBUSTIBLE
MATERIALS-18INCHES/455MM. CLEARANCE MAY BE REDUCED BY THE USE OF LISTED PIPE SHIELDS, WALL PROTECTORS OR OTHER MEANS APPROVED BY LOCAL BUILDING OR FIRE OFFICIALS. · COMPONENTS REQUIRED FOR MOBILE HOME INSTALLATION: OUTSIDE AIR KIT. · HORIZONTAL CONNECTOR NOT PERMITTED IN MOBILE HOMES · BOTH CHIMNEY SYSTEM AND CONNECTOR MUST BE LISTED TO: IN CANADA – ULC S-641 LISTED CONNECTOR AND ULC-S-629 LISTED CHIMNEY IN USA – UL-103 HT LISTED CONNECTOR AND CHIMNEY · USE COMPONENTS SPECIFIED IN PACIFIC ENERGY INSTALLATION INSTRUCTIONS.
P · APPLIANCE MUST BE INSTALLED WITH PEDESTAL OR LEG KIT ATTACHED.
· OPTIONAL COMPONENTS – FAN KIT (part # 11140001), FAN ELECTRICAL RATING: 115V, 60HZ, 1.0 AMP · DO NOT USE GRATE OR ELEVATE FIRE – BUILD WOOD FIRE DIRECTLY ON HEARTH. · DO NOT OVERFIRE – IF CHIMNEY OR CONNECTOR GLOWS, YOU ARE OVERFIRING.
L · CAUTION: RISK OF EXCESSIVE TEMPERATURES – OPERATE ONLY WITH FEED DOOR CLOSED. OPEN TO FEED FIRE ONLY. – KEEP ASH DUMP CLOSED DURING FIRING OF THE HEATER.
E · KEEP FURNISHINGS AND OTHER COMBUSTIBLE MATERIALS WELL AWAY FROM HEATER.
· REPLACE GLASS ONLY WITH CERAMIC GLASS. · COMBUSTIBLE FLOOR MUST BE PROTECTED BY A CONTINUOUS NON-COMBUSTIBLE MATERIAL
EXTENDED TO THE FRONT, SIDES AND BACK AS INDICATED. · INSPECT AND CLEAN CHIMNEY FREQUENTLY – UNDER CERTAIN CONDITIONS OF USE, CREOSOTE
BUILDUP MAY OCCUR RAPIDLY. · THIS WOOD HEATER NEEDS PERIODIC INSPECTION AND REPAIR FOR PROPER OPERATION. – CONSULT
THE OWNER’S MANUAL FOR FURTHER INFORMATION. · IT IS AGAINST FEDERAL REGULATIONS TO OPERATE THIS WOOD HEATER IN A MANNER INCONSISTANT
WITH THE OPERATING INSTRUCTIONS IN THE OWNER’S MANUAL · TO BE INSTALLED AS A FREESTANDING SPACE HEATER WITH THE CLEARNCES IN THE
MANUFACTURER’S INSTALLTION INSTRUCTIONS. NOT TO BE INSTALLED IN ANY FIREPLACE.

  • AS TESTED – PIPE SHIELD MAY BE REQUIRED BY LOCAL AUTHORITIES. ** COMBUSTIBLE ALCOVE SIZE: DEPTH – 3 FT. / .91 M MAX., HEIGHT 6 ft. / 1.83 m MIN.,

MINIMUM CLEARANCES TO COMBUSTIBLE MATERIALS/ DÉGAGEMENTS MINIMALES AUX
MATÉRIAUX COMBUSTIBLES
A. SIDEWALL TO UNIT/ MUR DE CÔTE / APPAREIL
B. BACKWALL TO UNIT/ MUR DE FOND / APPAREIL C. CORNER TO UNIT/ COIN / APPAREIL D. SIDEWALL TO CONNECTOR/ MUR DE CÔTE / RACCORD E. BACKWALL TO CONNECTOR/ MUR DE FOND / RACCORD F. CORNER TO CONNECTOR/ COIN / RACCORD
MUR ARRIERE BACK WALL

B

E

A

MUR COTE SIDE WALL

D

MUR ADJACENT ADJACENT WALL
C
F

RESIDENTIAL INSTALLATION USING SINGLE WALL CONNECTOR*/ INSTALLATION RÉSIDENTIELLE UTILISANT
UN RACCORD DE MUR SIMPLE

A.

10 in. / 356 mm

B.

10 in. / 229 mm

C.

7 in. / 152 mm

VISTA LE

D.

19-1/2 in. / 610 mm

E.

14-3/8 in. / 368 mm

F.

16-1/2 in. / 429 mm

ALDERLEA T4 LE

D.

20-7/8 in. / 650 mm

E.

14-3/8 in. / 371 mm

F.

17-1/2 in. / 435 mm

RESIDENTIAL and MOBILE HOME INSTALLATION USING DOUBLE WALL
CONNECTOR / INSTALLATION RÉSIDENTIELLE AVEC DÉGAGEMENT MINIMAL, UTILISANT UN
RACCORD DE MUR DOUBLE

A.

8 in. / 330 mm

B.

8 in. / 191 mm

C.

5 in. / 127 mm

VISTA LE

D.

17-1/2 in. / 584 mm

E.

12-3/8 in. / 330 mm

F.

14-1/2 in. / 403 mm

ALDERLEA T4 LE

D.

18-7/8 in. / 612 mm

E.

12-3/8 in. / 330 mm

F.

15-1/2 in. / 410 mm

DOS BACK I
H

IN CANADA AU CANADA H

· À UTILISER UNIQUEMENT AVEC DU COMBUSTIBLE SOLIDE. NE PAS UTILISER D’AUTRES TYPES DE CARBURANT. · INSTALLEZ ET UTILISEZ SELON LES INSTRUCTIONS D’INSTALLATION ET D’OPÉRATION FOURNI AVEC L’APPAREIL.. · CONTACTEZ LES OFFICIELS DE LA CONSTRUCTION OU DE SERVICE D’INCENDIE POUR DES INFORMATIONS QUANT AUX
RESTRICTIONS. PERMIS D’INSTALLATION ET INSPECTIONS DANS VOTRE RÉGION. · NE RELIEZ PAS CET APPAREIL À UN CONDUIT DE CHEMINÉE DESSERVANT DÉJÀ UN AUTRE APPAREIL . · UTILISEZ UN RACCORDEMENT NOIR OU CLASSÉ DE 24 MSG ET AVEC UN DIAMÈTRE D’AU MOINS 6 POUCES / 150 mm. · PEUT ÊTRE CONNECTÉ À UNE CHEMINÉE DE MAÇONNERIE ALIGNÉE PRÊTE À L’EMPLOI AVEC DES COMBUSTIBLES SOLIDES. · N’OBSTRUEZ PAS L’ESPACE SOUS LE CAISSON DU POÊLE · CONSULTEZ LE CODE LOCAL DE CONSTRUCTION ET LES INSTRUCTIONS DU FABRICANT QUANT AUX PRÉCAUTIONS À
PRENDRE LORSQUE VOUS FAITES PASSER UNE CHEMINÉE À TRAVERS D’UN MUR OU D’UN PLAFOND COMPOSÉS DE MATÉRIAUX COMBUSTIBLES. · NE FAITES PAS PASSER UN RACCORDEMENT DE CHEMINÉE À TRAVERS D’UN MUR OU D’UN PLAFOND COMPOSÉS DE MATÉRIAUX · DÉGAGEMENT MINIMAL ENTRE UN RACCORDEMENT DE CHEMINÉE À UN MUR SIMPLE ET TOUT MATÉRIEL COMBUSTIBLE – 18 POUCES / 455 mm. CE DÉGAGEMENT PEUT ÊTRE RÉDUIT EN UTILISANT DES PROTECTEURS DE TUYAUX CLASSÉS, PROTECTEURS DE MUR OU AUTRES MOYENS APPROUVÉS PAR LES OFFICIELS DE LA CONSTRUCTION OU DU SERVICE D’INCENDIE DE VOTRE RÉGION. CONNECTEUR HORIZONTAL NON PERMIS DANS MAISONS MOBILES · L’APPARIEL DOIT COMPORTER UN ENSEMBLE POUR PIEDSTABLE OU SUR PATTES. · PIÈCES REQUISES POUR INSTALLATION EN MAISON MOBILE OU EN ALCÔVE: NÉCESSAIRE D’APPROVISIONNEMENT D’AIR EXTÉRIEUR ET L’UN DES RACCORDS SUIVANTS: EN COMBINAISON AVEC L’UN DES SYSTÈMES DE CHEMINÉE COMPATIBLES SUIVANTS:
AU CANADA – LE ULC S-641 CONNECTEUR ENUMERES ET ULC-S-629 ONT ENUMERE CHEMINEE · PIÈCES EN OPTION – NÉCESSAIRES DE SOUFFLERIE, INDICES ÉLECTRIQUES DE SOUFFLERIE: 115V, 60HZ, 1.0 AMP. LE FIL
ÉLECTRIQUE NE DOIT PAS ÊTRE PLACÉ SOUS LE POÈTE. LE FIL ÉLECTRIQUE NE DOIT PAS ÊTRE PLACÉ SOUS LE POÊLE · ATTENTION: RISQUE DE TEMPÉRATURES EXCESSIVES – GARDES LE TIROIR DE CENDRES FERMÉ PENDANT L’ALLUMAGE DU
POÈTE. · OPÉREZ SEULEMENT LORSQUE LA PORTE D’ALIMENTATION EST FERMÉE. · OUVREZ SEULEMENT POUR ALIMENTER LE FEU. · GARDEZ LES MEUBLES ET AUTRES MATÉRIAUX COMBUSTIBLES BIEN ÉLOIGNÉS DU POÊLE. · REMPLACES LA VITRE AVEC UNIQUEMENT DE LA VITRE CÉRAMIQUE.

  • TEL QUO ÉPROUVÉ UN PROTECTEUR DE TUYAU PEUT ÊTRE REQUIS PAR LES AUTORITÉS LOCALES ** DIMENSION D’ALCOVE COMBUSTIBLE: PROFONDEUR – 3 PIEDS / .91M, HAUTEUR 7 PIEDS/2.1M, LARGEUR 4 PIEDS/1.2M
    MINIMUM. LE PLANCHER COMBUSTIBLE DOIT ÊTRE PROTÉGÉ PAR UN MATÉRIEL NON- COMBUSTIBLE TOUT D’UNE PIÈCE QUI DOIT S’ÉTENDRE DE PAR LE DEVANT, LES COTÉS ET L’ARRIÈRE TEL QU’INDIQUÉ. · CET APPRAREIL DE CHAUFFAGE AU BOIS DOIT FAIRE L’OBJETD’ENTRETIENS ET D’INSPECTIONS PÉRIODIQUES POUR UN FONCTIONNEMENT ADÉQUAT. CONSULTEZ LE MANUEL D’UTILISATION POUR PLUS D’INFORMATION. · À INSTALLER EN TANT QU’APPAREIL DE CHAUFFAGE AUTONOME AVEC LES DÉGAGEMENTS INDIQUÉS DANS LES INSTRUCTIONS D’INSTALLATION DU FABRICANT. NE PAS INSTALLER DANS UNE CHEMINÉE.

G. 18 INCHES / 450 MM H. 8 INCHES / 200 MM I. 8 INCHES / 200 MM

DATE OF MANUFACTURE

COTE

SIDE

U.S. ENVIRONMENTAL PROTECTION AGENCY.
Certified to comply with 2020 CRIB WOOD PARTICULATE EMISSION STANDARDS, using Method 28R// Certifié conforme aux normes sur les émissions de particules de 2020.

1.9 g/hr

060423

HEATER POELE
G FRONT DEVANT

IN U.S.A.

G. 16 INCHES / 405 MM H. 5 INCHES / 127 MM I. 0 INCHES / 0 MM

MANUFACTURED BY/ FABRIQUÉ PAR: PACIFIC ENERGY FIREPLACE PRODUCTS LTD.
2975 ALLENBY RD., DUNCAN, BC V9L 6V8

MADE IN CANADA/ FABRIQUÉ AU CANADA

100002909

3

This heater meets the U.S. Environmental Protection Agency’s 2020 crib wood emission limits for wood heaters sold after May 15, 2020 using Method 28R.
Under specific test conditions this heater has been shown to deliver heat at rates ranging from 13,500 to 23,200Btu/hr.
Emissions testing was performed by PFS-TECO Inc.

Efficiency and BTU Output

EPA Certified Emissions 1.9 grams per hour

LHV Tested Efficiency 1 78%

HHV Tested Efficiency 2 72%

EPA BTU Output 3

Maximum Wood Length 18 inches

Ideal Wood Length

Fuel

1 Weighted Average Lower Heating Value (LHV) efficiency as tested using CSA B415 Performance testing of solid-fuelburning heating appliances. LHV assumes the moisture is already in a vapour state so there is no loss of energy
2 Weighted Average Higher Heating Value (HHV) efficiency as tested using CSA B415 Performance testing of solid-fuelburning heating appliances. HHV includes the energy required to vaporize the water in the fuel
3 The range of BTU outputs is based on efficiency using CSA B415 Performance testing of solid-fuel-burning heating appliances and burn rates from the low and high EPA tests using Douglas Fir dimensional lumber.

13,494 to 23,186 btu/hr.

16 inches

Seasoned Cord wood

100003978

CAUTION: Never use gasoline, gasoline type lantern fuel, kerosene, charcoal lighter fluid or similar liquids to start or “freshen up” a fire in this heater. Keep all such liquids well away from the heater while it is in use.

Safety

Instruct all members of your family on the safe operation of the heater. Ensure they have enough knowledge of the entire system if they are expected to operate it. Stress the section on chimney fires and the importance of following the steps outlined “In Case of Chimney Fire”.
Chimney Smoke and Creosote Formation
When wood is burned slowly, it produces tar and other organic vapours, which combine with expelled moisture to form creosote. The creosote vapours condense in the relatively cool chimney flue of a slow burning fire. As a result, creosote residue accumulates on the flue lining. When ignited, this creosote makes an extremely hot fire. The chimney connector and chimney should be inspected periodically (at least once every two months) during the heating season to determine if a creosote buildup has occurred. If creosote has accumulated (3 mm. or more), it should be removed to reduce the risk of a chimney fire.
1. Highest smoke densities and emissions occur when a large amount of wood is added to a bed of hot coals and the air inlet is closed. The heated wood generates smoke, but without ample air, the smoke cannot burn. Smoke-free, clean burning requires small fuel loads, two or three logs at a time or 1/4 to 1/2 of fuel load and leaving the air inlet relatively wide open, especially during the first 10 to 30 minutes after each loading, when most of the smoke generating reactions are occurring. After 30 minutes or so, the air inlet can be turned down substantially without excessive smoke generation. Wood coals create very little creosote-producing smoke.
2. The cooler the surface over which the wood smoke is passing, the more creosote will be condensed. Wet or green wood contributes significantly to creosote formation as the excess moisture that is boiled off cools the fire, making it difficult for the tars and gases to ignite, thus creating dense smoke and poor combustion. This moisture-laden smoke cools the chimney, compounding the problem by offering the smoke the ideal place to condense.
In summary, a certain amount of creosote is inevitable. Regular inspection and cleaning is the solution. The use of dry, seasoned wood and ample combustion air will help to minimize annoying smoke emissions and creosote buildup.
Chimney Fires
The dangerous side effect of excessive creosote buildup is a chimney fire. This causes much higher than normal temperatures in the chimney and on its exterior surfaces. Temperatures inside the chimney can exceed 2000°F (1100°C). Ignition of nearby or touching combustible material is more likely during a chimney fire. Proper clearances are critical to prevent damage during such a fire.

100003978

4

ALT 4-LE 180923-28

Chimney fires are easy to detect; they usually involve one or more of the following:
· Flames and sparks shooting out of the top of the chimney · A roaring sound · Vibration of the chimney
To Avoid a Chimney Fire
1. Burn wood cleanly. Do not burn wet wood or turn down the unit too quickly after loading.
2. Do not let creosote build up to a point where a chimney fire is possible.
3. Do not have fires in the heater that may ignite chimney fires. These are excessively hot fires, such as when burning household trash, cardboard, Christmas tree limbs, or even ordinary fuel wood; (eg. with a full load on a hot bed of coals and with the air inlet wide open for more time than is needed to completely char a fresh fuel load.)
4. The Chimney and connector pipe should be inspected /cleaned periodically.

In the event of a Chimney Fire
1. Prepare to evacuate to ensure everyone’s safety. Have a well understood plan of action for evacuation. Have a place outside where everyone is to meet.
2. Close air inlet on stove.
3. Call local fire department. Have a fire extinguisher handy. Contact your local municipal or provincial fire authority for further information on how to handle a chimney fire. It is most important that you have a clearly understood plan on how to handle a chimney fire.
4. After the chimney fire is out, the chimney must be cleaned and checked for stress and cracks before starting another fire. Also check combustibles around the chimney and the roof.
We strongly recommend that your chimney be inspected by professionals who are certified by one of the following;
NFI (National Fireplace Institute®) in the United States, CSIA (Chimney Safety Institute of America) in the United States and Canada, WETT (Wood Energy Technology Transfer) in Canada or APC (Association des Professionnels du Chauffage) in Quebec
Curing of the Paint Finish
To achieve the best finish, the paint on your stove must be baked on. When burning your stove for the first 2-3 times it is very important that the room be well ventilated. Open all windows and doors. Smoke and fumes caused by the curing process may cause discomfort to some individuals.
· Slowly bring the stove to a medium burn, for about 45 minutes. Then increase the to a high burn for an additional 45-60 minutes
WARNING: Never use chemicals or any other volatile liquid to start a fire. Do not burn garbage, or flammable fluids such as gasoline, naptha, or engine oil.

ALT 4-LE 180923-28

5

100003978

Operation
CAUTION: Hot while in operation. Keep children, clothing and furniture away. Contact may cause skin burns.

WARNING: Always keep loading door closed when burning. This heater is not designed for open door burning.

WARNING: No alteration or modification of the combustion air control assembly is permitted. Any tampering will void warranty and could be very hazardous.

WARNING: Do not use grates or andirons to elevate the fuel. Burn directly on the fire bricks. Replace broken or missing bricks. Failure to do so may create a hazardous condition.

Wood Selection

This heater is designed to burn natural wood only. Higher efficiency and lower emissions generally result when burning air-dried seasoned hardwoods, as compared to softwoods or to green or freshly cut hardwoods.

Wood should be properly air dried (seasoned) for six months or more. Wet or undried wood will cause the fire to smoulder and produce large amounts of smoke and creosote. Wet wood also produces very little heat and tends to go out often. Wood should be stored under cover away from open flame or heat sources.

DO NOT BURN : · Salt water wood · Wet or green wood · Garbage · Lawn clippings/yard waste · Railroad ties · Materials containing rubber, including tires · Construction or demolition debris · Waste petroleum products, paints, paint thin-
ners, or asphalt products

· Treated wood · Coal/charcoal · Solvents · Unseasoned wood · Manure or animal remains · Materials containing plastic · Materials containing asbestos · Paper products, cardboard, plywood, or
particleboard.

  • These materials contain chlorides which will rapidly destroy metal surfaces and void warranty.

Burning these materials may result in the release of toxic fumes or render the heater ineffective and cause smoke.

Do not burn anything but wood. Other fuels, eg. charcoal, can produce large amounts of carbon monoxide, a tasteless, odorless gas that can kill. Under no circumstances should you attempt to barbecue in this heater.

The prohibition against burning these materials does not prohibit the use of fire starters made from paper, cardboard, saw dust, wax and similar substances for the purpose of starting a fire in an affected wood heater.

How to Test Your Wood

Add a large piece of wood to the stove when it has a good large bed of coals. It is dry if it is burning on more than one side within one minute. It is damp if it turns black and lights within three minutes. If it sizzles, hisses and blackens without igniting in five minutes it is soaked and should not be burnt

100003978

6

ALT 4-LE 180923-28

Lighting a fire
WARNING: Never use chemicals or any other volatile liquid to start a fire.
1. Adjust the air control to the “High” position (all the way to the left) and open the door.
2. Place crumpled newspaper in the centre of the heater and crisscross with several pieces of dry kindling. Add a few small pieces of dry wood on top.
3. Ignite the paper and leave the door ajar approximately 1/2″(13mm) – 1″(25mm) until the wood kindling is fully engulfed in flame. Do Not leave stove unattended while the door is open
4. After the kindling is fully engulfed add a few small logs. Close door.
5. Begin normal operation after a good coal base exists and wood has charred.
Normal Operation
WARNING: This wood heater has a manufacturer-set minimum low burn rate that must not be altered. It is against federal regulations to alter this setting or otherwise operate this wood heater in a manner inconsistent with the operating instructions in this manual.
1. Set air control to a desired setting. If smoke pours down across the glass (waterfall effect) this indicates you have shut the control down too soon or you are using too low a setting. The wide range of control makes finding the desired setting for your application easy. As every home’s heating needs vary (ie. insulation, windows, climate, etc.) the proper setting can only be found by trial and error and should be noted for future burns.
2. To refuel, adjust air control to high, and give the fire time to brighten. Open the door slowly, this will prevent back puffing.
3. Use wood of different shape, diameter and up to 18″(457mm in length. Load your wood east-west and try to place the logs so that the air can flow between them. Always use dry wood.
4. Do not load fuel to a height or in such a manner that would be hazardous when opening the door.
5. For extended or overnight burns, unsplit logs are preferred. Remember to char the wood completely on maximum setting before adjusting air control for overnight burn.
· Burn wood only, dry and well seasoned. The denser or heavier the wood when dry, the greater its heat value. This is why hardwoods are generally preferred. Green or wet wood will cause a rapid buildup of creosote. If you feel it is necessary to burn wet or unseasoned wood, do so only with the air inlet set open enough to maintain a good strong fire and fairly high chimney temperatures. Do not attempt to burn overnight using green wood or wet wood. Wet wood can cause up to 25% drop in heater output, as well as contributing significantly to creosote buildup.
DO NOT OVER FIRE THIS HEATER: Attempts to achieve heat output rates that exceed heater design specifications can result in permanent damage to the heater and chimney. A glowing red, top or vent pipe are indications of over firing. Failure to rectify an over firing condition can be hazardous and may void the manufacturer’s warranty.

ALT 4-LE 180923-28

7

100003978

Restarting After Extended or Overnight Burns
1. Open door and rake hot embers towards the front of the heater. Add a couple of dry, split logs on top of embers, close door.
2. Adjust air control to high and in just a few minutes, logs should begin burning.
3. After wood has charred, reset air control to desired setting.
4. To achieve maximum firing rate, set control to high “H”. Do not use this setting other than for starting or preheating fresh fuel loads.
Proper Draft
1. Draft is the force which moves air from the appliance up through the chimney. The amount of draft in your chimney depends on the length of the chimney, local geography, nearby obstructions and other factors.
2. Too much draft may cause excessive temperatures in the appliance. An uncontrollable burn or a glowing red stove part or chimney indicates excessive draft.
3. Inadequate draft may cause back puffing into the room and plugging of the chimney. Smoke leaking into the room through appliance and chimney connector joints indicates inadequate draft.
Remember the “correct” air control setting is affected by variables such as type of wood, outside temperature, chimney size and weather conditions.
Ash Removal
Caution: Ashes are to be removed only when the heater is cold. Whenever ashes get 3″(76mm) to 4″(102mm) deep in your firebox, and when fire has burned down and cooled, remove excess ashes. Leave an ash bed approximately 1″ (25 mm) deep on the firebox bottom to help maintain a hot charcoal bed.
Ash Clean out system:
The ash dump handle is located under the ash lip on the left hand side. To operate ash dump, pull handle out 1/2″(13mm) and turn clockwise. This will unlock the ash dump and allow it to open. Hold handle open while pulling ashes into the opening. Avoid large embers as these still contain heat value. Release handle and push in to lock. Ensure ash dump door is properly engaged. Fill the cavity with the remaining ash level with the firebox floor. Lift and pull out ash pan and discard ashes into metal container. Replace ash pan and ensure it is seated properly.
Do not burn with ash dump door open. Doing so will create a hazardous condition. Always leave about 1″(25mm) of ash when cleaning.
Disposal of Ashes
Ashes should be placed in a metal container with a tight fitting lid. The closed container of ashes should be placed on a non-combustible floor or on the ground, well away from all combustible materials, pending final disposal. If the ashes are disposed of by burial in soil or otherwise locally dispersed, they should be retained in closed container until all cinders have thoroughly cooled. Other waste should not be placed in this container.

100003978

8

ALT 4-LE 180923-28

Maintenance
WARNING: Never use chemicals or any other volatile liquid to start a fire. Do not burn garbage, or flammable fluids such as gasoline, naptha, or engine oil.
WARNING: ONLY USE MATERIALS SUPPLIED BY MANUFACTURER WHEN DOING MAINTENANCE OR REPLACEMENTS.
1. If glass becomes darkened through slow burning or poor wood, it can readily be cleaned with fireplace glass cleaner when stove is cold. Never scrape with an object that might scratch the glass. The type and amount of deposit on the glass is a good indication of the flue pipe and chimney buildup. A light brown dusty deposit that is easily wiped off usually indicates good combustion and dry, well-seasoned wood and therefore relatively clean pipes and chimney. On the other hand, a black greasy deposit that is difficult to remove is a result of wet and green wood and too slow a burning rate. This heavy deposit is building up at least as quickly in the chimney.
2. DOOR GASKETS – The gasket used by Pacific Energy (7/8″fiberglass rope) requires only light pressure to seal. This will prolong seal life. It is important that the door seal be maintained in good condition. Periodically inspect seals and replace if necessary. Follow the instructions included in the kit, obtainable from your nearest Pacific Energy dealer.
3. DOOR GLASS – Do not slam loading door or otherwise impact glass. When closing door, make sure that no logs protrude to impact the glass. If the glass gets cracked or broken, it must be replaced before using the stove. Replacement glass can be obtained from your dealer. Use 10-1/2″(266mm) x 16-1/2″(419mm) x 5 mm. Ceramic glass only. Do not substitute with any other type.
· To remove broken glass, undo the four retaining screws and remove clamps and frame, noting position for re-assembly. Remove all particles of glass . Be careful as they are very sharp. Install new glass complete with gasket. Replace frame, clamps and screws.
CAUTION: – do not overtighten, tighten screws very carefully – do not clean glass when hot – do not use abrasive cleaners on glass
4. The area where boost combustion air enters the firebox must be kept clear of excessive ash buildup which will block air flow. This area is at the front of the firebox.
5. Do not store wood within heater installation clearances, or within the space required for fuel loading and ash removal. Keep the area around the heater clean and free of loose combustibles, furniture, newspapers, etc.
6. Establish a routine for the fuel, wood burning and firing technique. Check daily for creosote buildup until experience shows how often you need to clean to be safe.
7. Be aware that the hotter the fire, the less creosote is deposited. Weekly cleaning may be necessary in mild weather, even though monthly cleaning is usually enough in the coldest months when burning rates are higher. When wood is burned slowly, it produces tar and other organic vapours, which combine with expelled

ALT 4-LE 180923-28

9

100003978

Maintenance Checks
Check the following parts for damage such as cracks, excessive corrosion, burned out sections and excessive warping: (See website for descriptions and more detail)
Weekly:
· Firebrick – Visual, for cracking. · Door Gasket – sagging, placement, damage.
Monthly
· Brick rail tabs and brick rails. · Air riser tube in the back of the firebox. · Back side of airwash chamber. · Baffle locking pin. · Boost openings.
When Cleaning the Chimney System:
· Top baffle board/blanket. · Baffle. · Top heat shield and mounting bolt. · Baffle Gasket. · Brick Rails. · Manifold.
Blower:
· The blower should be cleaned out a minimum every six months by using a vacuum on the grill openings in the back and bottom of the blower casing to remove any dust and debris.
Baffle:
· Some warping of the baffle is normal (up to 1/4″ or .65cm). Replace if the baffle has permanent warping greater than this or has cracking or breakage.
· Please contact your Dealer if you experience any of the damage listed above. Continuing to operate your stove with broken parts may accelerate damage to other parts and may void your warranty

100003978

10

ALT 4-LE 180923-28

Baffle / Tube Removal
Chimney connector pipe should be disconnected from stove to clean and inspect. Only if this is not possible should you remove baffle assembly.
DO NOT OPERATE WITH BAFFLE ASSEMBLY, TUBES OR INSULATION REMOVED.
Baffle Removal
1. Slide the Ceramic Board located above the tubes towards the front of the stove. Remove retaining pin at the back of the firebox, just under the baffle.
2. Lift the Baffle up to disconnect from the Baffle supply tube.
3. Move the Baffle to one side then tilt it sideways to drop down and remove from firebox. You may need to remove the opposite side brick rail to allow the Baffle to drop down. – To remove the Brick Rail, remove the brick directly under it then lift the rail up and inward to clear the locating pins
4. Inspect the gasket between baffle and supply tube. If necessary, replace with gasket (prt#80000365) available from your Pacific Energy dealer.
5. Re-install baffle assembly in reverse order. The two side pieces of blanket insulation must be tight against the side rails. The Ceramic Board on top of the tubes must be pushed back tight against the Baffle.
Tube / Baffle Board Removal 1. With a set of vise-grips, grasp the front baffle tube on the right, slightly away from the baffle air assembly.
While squeezing tightly, use a hammer to hit the pliers and pull the tube to the right to disengage the tube from the hole on the left. Allow the tube to hang freely from the hole on the right.
2. Repeat step #1 for rear baffle tube.
3. Grasp the front edge of the baffle board and pull forward. Guide the board down and through the door opening. Caution – Baffle Board material is very fragile.
Installation 1. With the holes facing down/forward and the notch to the left side, insert a baffle tube into the hole in the
baffle air channel on the right at an angle and then raise and insert into the opposite hole on the left side baffle air assembly.
2. With a set of vise-grips, grasp the baffle tube on the left, slightly away from the baffle air assembly. While squeezing tightly, use a hammer to hit the pliers and push the tube to the left to engage the tube in the hole on the left.
3. With the rear tube installed, Insert the baffle board above the tube, between the tube and the side hold down tabs.
4. Repeat steps #1 & #2 with the remaining baffle tube, being careful not to damage the board.
5. Slide the baffle board back until the lower edge is tight against the baffle.

ALT 4-LE 180923-28

11

100003978

Assembly
1. Carefully remove wood crating top and supports. 2. Remove plastic cover. 3. Remove the Brick Pack from the firebox. Install Firebricks (see section; Firebrick Installeation) after stove
is in its final location, and the chimney is installed.

29 3/8″ 745mm

27 3/4″ 705mm

Dimensions
7 3/8″ 190mm
28 1/8″ 715mm

Figure 1: T4 LE dimensions.

22 3/4″ 580mm

100003978

12

ALT 4-LE 180923-28

Floor Protector
The stove may be installed on a combustible floor provided noncombustible ember protection is used. This protection must extend as follows:

U.S.A. Only
Minimum Width – 34″(864mm) Minimum Overall Depth – 35″(890mm)
Non-combustible floor protector

In USA: 16″ (406 mm) to the front and 8″ (203 mm) to the sides of the fuel loading door opening. See Figure #2. This protection is also required under the chimney connector and 2″ (51 mm) beyond each side if using any horizontal venting.

3″ 75mm

8″ 203mm

8″ 203mm

16″ [406mm]

Figure 2: T4 Floor protector – USA.

CANADA Only
Minimum Width – 44″(1.120m) Minimum Overall Depth – 45″(1.145m)
8″ 203mm

In Canada: 18″ (457 mm) on the firing side and 8″ (203 mm) to the other sides.

8″ 203mm

8″ 203mm

ALT 4-LE 180923-28

Non-combustible floor protector
18″ [460mm]

Figure 3: T4 Floor protector – CAN.

13

100003978

Clearances:

Residential Installation

17 3/8″ 440mm

10″ 255mm
10″ 255mm
23 7/8″ 605mm

Single Wall Flue Connector
10″ 255mm

10″ 255mm

10″ 255mm

20 1/2″ 520mm

7″ 180mm

7″ 180mm

15 3/8″ 390mm

8″ 205mm

Double Wall Flue Connector
8″ 205mm

8″ 205mm

8″ 205mm

8″ 205mm

21 7/8″ 555mm
Figure 4: T4 LE Minimum clearances.

Alcove: Min. Height 7′ (2.13m) Max. Depth 3′ (915 mm)

18 1/2″ 470mm

5″ 130mm

5″ 130mm

Clearances may be reduced with various heat shielding/insulating materials. Consult CSA B365 or NFPA 211 and local fire codes and authorities for approval. For close clearances, use a listed double-wall connector.
NOTE: local/national codes or regulations may override some guidelines in this manual
We recommend that our products be installed and /or serviced by professionals who are certified by one of the following;
NFI (National Fireplace Institute®) in the United States, CSIA (Chimney Safety Institute of America) in the United States and Canada, WETT (Wood Energy Technology Transfer) in Canada or APC (Association des Professionnels du Chauffage) in Quebec

100003978

14

ALT 4-LE 180923-28

Warning: Under no circumstances is this heater to be installed in a makeshift or “temporary” manner. It may be fired only after the following conditions have been met.
DO NOT ATTEMPT TO CONNECT THIS HEATER TO ANY AIR DISTRIBUTION DUCT. DO NOT INSTALL IN ANY FIREPLACE.
Outside combustion air or fresh air into the room may be required in your area, consult local building codes (see Combustion Air section).
Chimney and Connector
· The chimney system must be a ULC-S629 or UL-130HT listed Stainless chimney or a Masonry chimney suitable for use with solid fuel, that is lined, in good condition and meets fire and building codes.
· The chimney flue size should be the same as the stove outlet (6 inches) for optimal performance. Reducing or increasing the flue size may adversely affect stove performance.
· Chimney flue exit is to be 3 feet (1 m.) above roof and two feet (0.6 m) above highest projection within 10 feet (3 m).
· The installation must meet all local codes.
· Do not connect this unit to a chimney flue serving another appliance. Minimum system height is 15 feet (4.6 m.) (measured from base of appliance).
BOTH CHIMNEY SYSTEM AND CONNECTOR MUST BE LISTED TO: IN CANADA – ULC S-641 LISTED double wall connector and ULC-S629 LISTED CHIMNEY, IN USA – UL-103 HT LISTED CONNECTOR AND CHIMNEY
When using a Double-Wall Connector
· Use a listed double-wall connector.
· If a listed chimney and double-wall connector are to be connected to the stove, install all components as per the chimney/connector manufacturer’s installation requirements.
When using a Single-Wall (smoke pipe) Connector The single wall pipe section must be:
· If you are using smoke pipe/chimney connector in conjunction with the listed chimney system, consult local/national fire or building codes for connector installation. Follow the chimney manufacturer’s complete instructions for the installation of the chimney system.
· As short and straight as possible, use six inch diameter, 24 gauge black pipe that is clean and in new condition.
· Installed with the crimped or male ends pointing down. (This will carry any liquid creosote or condensation back into the stove) and secured at every joint and collar with 3 sheet metal screws.
· The chimney connector shall not pass through an attic, roof space, closet or similar concealed space, floor, or ceiling. Where passage through a wall, or partition of combustible material is desired, the installation shall conform to CAN/CSA-B365, Installation Code for Solid-Fuel-Burning Appliances and Equipment

ALT 4-LE 180923-28

15

100003978

Installation Procedure
1. Select the position for your wood stove based on the clearances diagram. Position the stove and floor protection.
2. Mark the position for the hole in the ceiling and roof by using a string and plumb-bob hanging over the exact center of the stoves flue pipe.
3. Check that the intended location will not interfere with floor joists, ceiling joists or rafters before proceeding further. Adjust if necessary and reconfirm the clearance’s from the stove to combustibles.
4. Carefully follow the directions of the listed chimney for installation of the chimney system from the ceiling through to the rain cap. This may include framing in holes etc.
5. Start installing smoke pipe (chimney connector), slip crimped edge of the pipe inside the stove collar. Use holes provided in collar to secure pipe with two screws.
6. Install the remaining lengths of pipe one on top of the other up to the finished height of the chimney and using the manufacturers approved adapter, secure to each other. A slip section can make this easier.
Combustion Air
Intake or combustion air can be supplied to the stove in one of two ways. Consult your local building code or CAN/CSA-B365, Installation Code for Solid- Fuel-Burning Appliances and Equipment before proceeding.
1. Outside air supply – (Necessary for mobile home installation, optional for residential installation). Outside air may be drawn from either underneath the stove or from behind.
· To draw outside air through the floor – This hole must get its air from a ventilated crawl space or be extended with duct to the outdoors (see Figure

5,6, Page 17-18). The use of outside combustion air for residential

installation requires the unit to be secured to the structure to prevent dislodging of the air duct.
· Cut or drill a hole in the floor, (large enough to fit 4″ metal venting) behind the ash box enclosure. Install metal venting thru the hole and under the floor as required by building code. Once the stove is in place, attach the 4″ OAIR adapter to the Ash Box Enclosure. Connect the adapter to the metal with 4″(100mm) i.d. flexible metal ducting.
· To draw outside air from behind the stove, Use a 4″(100mm) Wall Air Intake. Following the Air Intake Kit’s instructions Cut or drill the recommended size hole through the wall behind the unit. Install the 4″ Intake Adapter over the hole in the rear of the Ash Box enclosure. Attach flexible metal ducting between the intake adapter and the Air Intake kit.
2. Room air supply – The stove will draw its air from the room through the opening in the Ash Box Enclosure and into the firebox intake.
Note: The living space around the heater must be well ventilated with good air circulation. Anything that may cause a negative pressure can cause gases or fumes to be pulled into the living area. During extremely cold weather, and especially when burning at very slow rates, the upper parts of the exposed chimney may ice up, partially blocking the flue gases. If blockage occurs, flue gases may enter living space.

100003978

16

ALT 4-LE 180923-28

Follow chimney manufacture specifcations for distance between vent termination heigth and chimney at roof line. Also consult local building regulations.

Spark arrester rain cap

Listed Insulated Chimney
Storm collar

Roof flashing

Minimum 7′ [2.1m] Ceiling Height
The chimney may incorporate an offset. To do this safely, all sections of listed connector, offset elbows and chimney section must be screwed together by at least three sheet metal screws per joint. The chimney must be suitably supported by the chimney manufacturer’s listed offset support. All vent manufacturer or national fire code clearances to combustible must be observed.

56″ [1.42m] Minimum
Chimney connector

Combustibles in front of the unit

48″ [1.2 m]

as per Local and Federal
codes

Chimney Support Wall Thimble

12″ [300mm] Minimum first

  • section of pipe

Alternate up and out installation

  • Unit may be harder to start. Please provide as much vertical length for the first section of pipe as possible

Non-combustible Ember Protector

  • 4″ (102 mm) diameter air inlet with rodent screen.
  • If the crawl space is well ventilated it is not necessary to extend air inlet to outside.

Figure 5: T4 residential venting.

ALT 4-LE 180923-28

17

4″ diameter hooded air inlet or 90 elbow turned down with rodent screen.
100003978

Ensure that the Masonry chimney meets all National Fire Protection Association and local building codes. Have the chimney cleaned and inspected by a professional to ensure there are no cracks, weak mortar or other signs of deterioration. See vent manufactuer’s installation instructions for further information

Fireclay Flue Liner Concrete Cap
Chimney

6″ S.S. liner

Minimum Ceiling Height 7′ (2.1 m)

56″ (1.42m) Minimum

Combustibles in front of the unit

48″ (1219 mm)
Non-combustible Ember Protector

Chimney Connector

Approved Through Wall Installation

  • 4″(102mm) diameter air inlet with rodent screen
  • If the crawl space is well ventilated it is not necessary to extend air inlet to outside

Figure 6: T4 Venting to a masonry chimney.

100003978

18

Hooded vent or 90° elbow turned down.
ALT 4-LE 180923-28

Through Wall Installations (as per NFPA 211)

ATTENTION: VAPOUR BARRIER MUST BE MAINTAINED WHEREVER CHIMNEY OR OTHER COMPONENTS PENETRATE TO THE EXTERIOR OF THE STRUCTURE. SEE LOCAL BUILDING CODES FOR PROPER AND APPROVED METHODS OF MAINTAINING VAPOUR BARRIER.

SYSTEM A

Minimum chimney clearance to brick and combustibles 2″ (51 mm).
Minimum clearance 12″ (305 mm) of brick

Chimney flue

Minimum 12″ (305 mm) to combustibles
Figure 7: System A

Chimney connector
Fireclay liner
Masonry chimney constructed to NFPA 211

Minimum Clearance 12 in. (305mm) to combustibles

System A. Minimum 3.5 in. (90 mm) thick brick masonry wall framed into combustible wall with a minimum of 12 in. (305 mm) brick separation from clay liner to combustibles. Fireclay liner (ASTM C 315, Standard Specifications for Clay Fire Linings, or equivalent), minimum 5/8 in. (16 mm) wall thickness, shall run from outer surface of brick wall to, but not beyond, the inner surface of chimney flue liner and shall be firmly cemented in place.

SYSTEM B

Minimum chimney clearance from masonry to sheet steel supports and combustibles 2″ (51 mm)

Nonsoluble Factory built refractory chimney length cement

Minimum clearance 9″ (229 mm)
Chimney connector

Chimney length

flush with inside

of flue

Air space: 9″ (229 mm) min.

Chimney flue

Masonry chimney constructed to NFPA 211

Use chimney manufacturers’ parts to attach connector securely
Solid-insulated, listed factory built chimney length

Sheet steel supports

Figure 8: System B.

Minimum Clearance 9 in. (229mm) to combustibles

System B. Solid-Insulated, listed factory-built chimney length of the same inside diameter as the chimney connector and having 1 in. (25.4 mm) or more of insulation with a minimum 9 in. (229 mm) air space between the outer wall of the chimney length and combustibles.

The inner end of the chimney length shall be flush with the inside of the masonry chimney flue and shall be sealed to the flue and to the brick masonry penetration with non-water-soluble refractory cement. Supports shall be securely fastened to wall surfaces on all sides.

Fasteners between supports and the chimney length shall not penetrate the chimney liner.

ALT 4-LE 180923-28

19

100003978

SYSTEM C
Minimum chimney clearance from masonry to sheet steel supports and combustibles 2″ (51 mm)

Two ventilated air channels, each 1″ (25.4 mm)
Chimney connector

Chimney flue

Minimum 6″ (152 mm) glass fiber insulation

Two ventilated air channels,

each 1″ (25.4 mm);

Masonry chimney

Sheet steel supports

construction of sheet steel constructed to NFPA 211

Figure 9: System C

Minimum Clearance: 6 in. (152mm) to combustibles
System C. Sheet steel chimney connector, minimum 24 gauge [0.024 in. (0.61 mm)] in thickness, with a ventilated thimble, minimum 24 gauge [0.024 in. (0.61 mm)] in thickness, having two 1 in. (25.4 mm) air channels, separated from combustibles by a minimum of 6 in. (152 mm) of glass fiber insulation. Opening shall be covered, and thimble supported with a sheet steel support, minimum 24 gauge [0.024 in. (0.61 mm))] in thickness.
Supports shall be securely fastened to wall surfaces on all sides and shall be sized to fit and hold chimney section. Fasteners used to secure chimney section shall not penetrate chimney flue liner.

SYSTEM D

Minimum chimney clearance to sheet steel supports and combustibles 2″ (51 mm)

Sheet steel supports

Minimum clearance 2″ (51 mm)

Chimney section

1″ (25.4 mm) air space to chimney length

Chimney flue

Chimney connector

Chimney connector

Air space:

Chimney length

2″ (51 mm) min.

Sheet steel supports

Masonry chimney

constructed to NFPA 211

Figure 10: System D

Minimum Clearance: 2 in. (51mm) to combustibles

System D. Solid-Insulated, listed factory-built chimney length with an inside diameter 2 in. (51 mm) larger than the chimney connector and having 1 in. (25.4mm) or more of insulation, serving as a pass-through for a single-wall sheet steel chimney connector of minimum 24 gauge [0.024 in. (0.61 mm)] thickness, with a minimum 2 in. (51 mm) air space between the outer wall of chimney section and combustibles.

Minimum length of chimney section shall be 12 in. (305 mm). Chimney section concentric with and spaced 1 in. (25.4 mm) away from connector by means of sheet steel support plates on both ends of chimney section. Opening shall be covered, and chimney section supported on both sides with sheet steel supports of minimum 24 gauge [0.024 in. (0.61 mm)] thickness.

Supports shall be securely fastened to wall surfaces on all sides and shall be sized to fit and hold chimney section. Fasteners used to secure chimney section shall not penetrate chimney flue liner.

100003978

20

ALT 4-LE 180923-28

Mobile Home Installation
These mandatory requirements for installation into a mobile Home, are in addition to those listed under Residential Installation.
Clearances to combustible surfaces and materials are shown below.
Use Only Double Wall Flue Connector
for Mobile Home

15 3/8″ 390mm

8″ 205mm

8″ 205mm

18 1/2″ 470mm

5″ 130mm

8″ 205mm

8″ 205mm

8″ 205mm

21 7/8″ 555mm

Alcove: Min. Height 7′ (2.13m) Max. Depth 3′ (915 mm)

Figure 11: T4 LE Mobile Home Clearances.

5″ 130mm

Warning: Under no circumstances is this heater to be installed in a makeshift or “temporary” manner. It may be fired only after the following conditions have been met.

· DO NOT CONNECT THIS UNIT TO A CHIMNEY FLUE SERVING ANOTHER APPLIANCE.

· DO NOT INSTALL IN A SLEEPING ROOM.

· CAUTION: THE STRUCTURAL INTEGRITY OF THE MOBILE HOME FLOOR, WALLS AND CEILING/ ROOF MUST BE MAINTAINED.

· The stove must be permanently anchored to the floor. Use the holes located in the bottoms of the legs.

· Outside air supply must be used for Mobile Home installations –

· This heater must be installed with listed double-wall connector and compatible ULC-S629 or UL-103HT listed chimney system.

NOTE: Install all chimney components to the connector and chimney manufacturer’s installation requirements. Consult your chimney supplier/manufacturer for installation advice.

Consult local Builing codes and Fire authorities for approval.

ALT 4-LE 180923-28

21

100003978

Trouble Shooting

Problem
Excessive Creosote Build-up
Glass is Dirty Low Heat Output

Cause

  1. Wood is too wet 2) Turning down air control
    too soon 3) Draft too low
  2. See 1, 2, and 3 above 2) Door Gasket leakage

Cure
– Use dry wood
– Do not turn down until: a) there is a good bed of coals b) the wood is charred
– Chimney plugged or restricted, check flue – Improper chimney height and/or diameter – Provide outside air for combustion – Check draft in chimney and system, alter as
needed.
– Replace gasket – Check door latch

  1. Wood may be wet 2) Fire too small 3) Draft too low

– Check wood and use drier wood if required.
– Build a larger fire – Open draft control to increase burn rate. – Chimney plugged or restricted
Inspect and clean

Won’t Burn Overnight Stove Won’t Burn

  1. Air control set too high 2) Not enough wood 3) Draft too high
  2. Combustion air supply is blocked

– Set control lower – Unsplit wood is preferred for overnight burns – Excessive chimney height and/or diameter,
see page 11
– Check outside air supply for obstructions – Check that room air cover is removed.
– Chimney plugged or restricted Inspect and clean

100003978

22

ALT 4-LE 180923-28

Optional Blower
The optional blower kit (kit #11140001) is equipped with a three prong power cord and may be installed at any time. Follow installation instructions supplied with the kit. Route power supply cord away from heater.
Electrical rating: 115 volts A.C.-1.1 amps. Fan output rating: 140 CFM
Blower Operation
Proper blower speed matched with air control setting will ensure peak performance from your stove. Operate as follows:
· Air control set to “L” (low), operate blower speed control on “Low”. · Air control set between “L” and “H” (low and high), operate blower speed control at desired setting.
Automatic: To operate the blower automatically, set the rocker switch on the side of the fan housing to “Auto” and set the speed control to desired setting. This will allow the fan to turn on as the stove heats up to operating temperature. It will also shut the blower off after the fire has gone out and the unit cooled to below a useful heat output range.
Manual: To manually operate the blower, set the rocker switch to “Man” and set the speed control to desired setting. This will bypass the sensing device and allow full control of the blower. Switching from “Auto” to “Man” or selecting speed may be done anytime.

Firebrick Installation

ITEM

Dimensions

E
A B
F

D A C
B

A 8 7/8″ x 4 3/8″ x 1 1/4″ B 8 7/8″ x 2 1/8″ x 1 1/4″ C 5 3/4″ x 4 3/8″ x 1 1/4″ D 4 3/8″ x 3 1/4″ x 1 1/4″ E 7″ x 3 1/4″ x 1 1/4″ F 4 1/4″ x 2 1/8″ x 1 1/4″

A A

A

A

A

D

A

E

A

A

A

F

B

Figure 12: Neo 1.6 LE Firebrick layout.

ALT 4-LE 180923-28

23

100003978

Begin firebrick installation with the rear wall.
1. Stand one “A” firebrick vertically behind the tab located on the brick rail. Slide the firebrick toward the center of the rear wall (Figure 13). Slide a 2nd “A” firebrick underneath the tab on the brick rail (Figure 13). Repeat steps 1 & 2 for the placement of the other “A” firebricks on the rear wall (Figure 13).
2. For the side walls: Stand an “A” firebrick against the side wall and up against the rear wall firebrick. Stand another “A” brick beside the first one followed by a narrow “B” firebrick (Figure 14).

Figure 13: Remaining rear wall firebricks in place.

Figure 14: Lower side wall firebricks in place.

3. Place a “D” firebrick on top of the previously placed “A” firebricks and slide this firebrick back toward the rear wall making sure that this firebrick tucks in behind the brick rail (Figure 15).

4. Slide an “E” firebrick under the side wall brick rail tab and rest on top of the three previously placed side wall firebricks (Figure 16). Repeat steps 2-4 on the other side (Figure 16).

Figure 15: Small side wall firebrick in position.

Figure 16: Final side wall firebrick in position.

100003978

24

ALT 4-LE 180923-28

5. Place two “A” firebricks on the firebox floor as shown. Place a third “A” firebrick against the rear wall as shown in (Figure 17).
6. Place the “C” firebrick so that it sits beside the ash dump, against the lefthand side wall and the “A” firebrick located directly behind the ash dump (Figure 17).

Figure 17: Floor brick in place.

Figure 18: Short, narrow brick installed in front row.

7. Place a short narrow “F” brick against the front right side of the floor (Figure 18) followed by a longer “B” brick in the center of the front row (Figure 19). Finish with the last “F” brick placed against the left side front row (Figure 20). Note: There will be a leftover gap behind the ash dump.
Note: there will be one brick left over as a spare.

Figure 19: Long narrow center brick in front row.

Figure 20: Final short narrow brick in front row.

ALT 4-LE 180923-28

25

100003978

Parts Diagram – Alderlea T4 LE

(WHEN ORDERING, INCLUDE PART NUMBER WITH DESCRIPTION)

1 TOP, ALT4 ………………………………………………………….. …METALIC BLACK PAINT ……………………… 80002471 …MAJOLICA BROWN ENAMEL……………… 80002472 …IVORY ENAMEL ………………………………… 80002473
2 SIDE, ALT4…………………………………………………………. METALIC BLACK PAINT ……………………… 80002474 MAJOLICA BROWN ENAMEL……………… 80002475 IVORY ENAMEL ………………………………… 80002476
3 DOOR CROWN, ALT4 METALIC BLACK PAINT ……………………… 80002477 MAJOLICA BROWN ENAMEL……………… 80002478 IVORY ENAMEL ………………………………… 80002479
4 ASHLIP, ALT4 METALIC BLACK PAINT ……………………… 80002480 MAJOLICA BROWN ENAMEL……………… 80002481 IVORY ENAMEL ………………………………… 80002482
5 LEG CASTING (1PC) …………………………………………… …METALIC BLACK PAINT ……………………… 80000012 …MAJOLICA BROWN ENAMEL……………… 80000054 …IVORY ENAMEL ………………………………… 80002491
6 DOOR ASSY ALT4 ………………………………………………. …BLACK PAINT (HANDLE ON LEFT) ……… 80002483 …MAJOLICA BROWN ENAMEL……………… 80002484 …IVORY ENAMEL ………………………………… 80002485

7 Gasket, Door, Neo 1.6/ Vista LE ………………… 80000156 8 Glass Retainer, Neo 1.6 / Vista LE ……………… 80002356 9 Glass(C/W Tape), Neo 1.6…………………………. 80000220 10 Door Handle, Alderlea, Left ………………………. 80000013 11 Air Control, Primary, ALT 4 LE……………………. 80002486 12 Ash Dump Assembly………………………………… 80001793 13 Ash Pan, Alt4 LE ……………………………………… 80002487 14 Leg Adapter, Alt4 LE ………………………………… 80002488 15 Firebrick, Neo 1.6 LE / Vista LE (Set) ………….. 80002355 16 Door Catch, Alt 1.2/4 LE …………………………… 80002492 17 Door Hinge, Alt 4 LE ………………………………… 80002489 18 Tube Air Box Gasket, Neo 1.6 LE / Vista LE … 80002359 19.. Tube Air Box (Rhs), Neo 1.6 LE / Vista LE ……80002365 20.. Tube Air Box (Lhs), Neo 1.6 LE / Vista LE…….80002358 21.. Tubes, Neo 1.6 LE / Vista LE (Set Of 2) ……….80002364 22.. Baffle Board, Neo 1.6 LE / Vista LE …………….80002357 23.. Flame Shield, Neo 1.6 LE / Vista LE, …………..80002360 24.. Baffle, Pin, (10pc)……………………………………..80000364 25.. Baffle, Neo 1.6 LE / Vista LE………………………80002361 26.. Brick Rail Set, …… Left/Right, Neo 1.6 LE/Vista LE ……………….80002363 27.. Baffle Blanket (Set), Neo 1.6 LE / Vista LE …..80002362 28.. Gasket, 2″ Baffle Tube, 10 pack …………………80000365 29.. Rear Brick Rail, Neo 1.6…………………………….80001723 30 Rear Air Deflector, Alt4 LE ………………………… 80002490

All parts may be ordered from your Pacific Energy dealer. Contact Pacific Energy for the location of the dealer nearest you.

100003978

26

ALT 4-LE 180923-28

23
22 21 20

18
8 9

19

7

3

10 6

2 16

1
27
26 25
24 28
29

11

4

12 17

2

14

13 15
5

ALT 4-LE 180923-28

27

100003978

©2023 Copyright Pacific Energy Fireplace Products LTD. Reproduction, adaptation, or translation without prior written permission is prohibited except as allowed under the copyright laws.
For technical support, please contact your retailer Web site: www.pacificenergy.net
2975 Allenby Rd., Duncan, BC V9l 6V8
Printed in Canada

References

Read User Manual Online (PDF format)

Loading......

Download This Manual (PDF format)

Download this manual  >>

Related Manuals