LINDY 38115 100m Cat.6 HDMI IR & RS-232 HDBaseT Extender with PoH & Ethernet Hub User Manual

LINDY 38115 100m Cat.6 HDMI IR & RS-232 HDBaseT Extender with PoH

& Ethernet Hub

IMPORTANT

Only use a direct Cat.5e/6/7 cable connection between the HDBaseT ports. Do not connect these ports to Network or Ethernet equipment or any active components

Safety Instructions

WARNING

Please read the following safety information carefully and always keep this document with product. Failure to follow these precautions can result in serious injuries or death from electric shock, fire or damage to the product.Touching the internal components or a damaged cable may cause electric shock, which may result in death. This device is a switching type power supply and can work with supply voltages in the range 100 – 240 VAC For worldwide usability four different AC adapters are enclosed: Euro type, UK type,US/Japan type and Australia/New Zealand type. Use the appropriate AC adapter as shown in the picture and ensure it is firmly secured in place and does not detach by pulling before installing into a power socket. To reduce risk of fire, electric shocks or damage:

•  Do not open the product nor its power supply. There are no user-serviceable parts inside.
•  Only qualified servicing personnel may carry out any repairs or maintenance.
•  Never use damaged cables.
•  Do not expose the product to water or places of moisture.
•  Do not use this product outdoors it is intended for indoor use only.
• Do not place the product near direct heat sources. Always place it in a well-ventilated place.
• Do not place heavy items on the product or the cables.
• Please ensure any adapters are firmly secured and locked in place before inserting into a wall socket

Instructions for Use of Power Supply

Introduction

Thank you for purchasing the 100m Cat.6 HDMI, IR & RS-232 HDBaseT Extender with PoH & Ethernet Hub. This product has been designed to provide trouble- free, reliable operation. It benefits from both a LINDY 2-year warranty and free lifetime technical support. To ensure correct use, please read this manual carefully and retain it for future reference. The Lindy 100m Cat.6 HDMI, IR & RS-232 HDBaseT Extender with PoH & Ethernet Hub is an end to end, premium solution for extending HDMI signals over long distances via Cat.6 network cable, while also providing an integrated 3 port Ethernet hub in either unit. HDBaseT is a globally recognised standard for high quality distribution of AV content and other technologies, including power and control, over longer distances via low cost Cat.6 or above cable. HDBaseT™ and the HDBaseT Alliance logo are trademarks of the HDBaseT Alliance. Please

Note:
The quoted lengths and resolutions are possible with a direct connection between Transmitter and Receiver using good quality Cat.6 solid core cable. Using a different cable type, or introducing wall plates, couplers or patch panels may result in a reduction of possible distances.

Package Contents

•  HDBaseT HDMI Extender, Transmitter
• HDBaseT HDMI Extender, Receiver
•  IR Emitter Cable, 2m
•  IR Receiver Cable, 2m
• 24VDC 1.25A Multi-country Power Supply (UK, EU, US & AUS), Barrel Size: 5.5/2.1mm Screw Type DC Jack
• Lindy Manual

Features

•  Supports resolutions up to 3840×2160@60Hz 4:2:0 8bit
•  Audio Pass-through of all HDMI audio formats
•  PoH (Power over HDBaseT) support, requiring only a power supply connection at the transmitter side of the installation
•  HDMI loop out port at the transmitter unit for local monitoring and viewing*
• Supports 10/100 Base-T Ethernet via the HDBaseT connection (2 x 3 Port 10/100 Ethernet)
• Supports hardware RS-232 link function and Infrared remote signal transmission
• Screw Type DC Jack for a secure power connection

Please Note:
The local HDMI output of the Transmitter may not be used at the same time as the HDBaseT connection

Specification

•  HDMI 1.4, 10.2Gbps Compliant
•  HDCP 2.2/1.4 Pass-through The following distance and resolution combinations are possible when using high-quality Cat.6 U/UTP or F/UTP cable: 100m:
• 1920x108060Hz 4:4:4 8bit
•  3D1920x1080 70m:
• 3840x216060Hz 4:2:0 8bit
• 3840x216030Hz 4:4:4 8bit
• 1920x108060Hz 4:4:4 8bit
• 3D1920x1080

Transmitter Ports Input:

•  HDMI Type A (Female)
•  IR (Female) Output:
• HDMI Type A (Female)
• RJ-45 (Female)
•  IR (Female) Receiver Ports: Input:
•  RJ-45 (Female)
•  IR (Female) Output:
• HDMI Type A (Female)
•  IR (Female) Bi-directional Ports:
• 3 x 10/100 Ethernet
•  RS-232
•  ESD Protection: ± 8kV (air-gap discharge)
• Human Body Model: ± 4kV (contact discharge)
•  Storage Temperature: -20°C – 60°C (-4°F – 140°F)
•  Relative Humidity: 20 – 90% RH (Non-condensing)
•  Metal Housing
•  Colour: Black
•  Power Requirements: AC100-240V 50/60Hz

Installation

The following steps are for an installation using HDMI equipment, if you are using DVI equipment, please substitute the HDMI cables for DVI to HDMI cables where required.

1.  Connect an HDMI source to the HDMI Extender Transmitter unit using a HDMI cable (maximum length 10m). If required you may connect a local HDMI monitor during installation – this monitor must be disconnected when the HDBaseT connection is being used.
2.  Connect one end of the Cat.6/7 cable (max. length 100m) to the HDBaseT link port on the Transmitter and the other end to the Receiver. Use solid core installation cable of at least Cat.6 UTP.
3.  Use another HDMI cable (maximum length 10m) to connect an HDMI display device to the HDMI output port on the Receiver unit.
4.  For RS-232 Extender functionality, connect a DB-9 cable on the Transmitter and on the Receiver.
5.  For additional Infrared remote signal functionality, connect the included IR cables to the units and place the transmitter in front of the HDMI device’s IR receiver.
6.  For Ethernet functionality, connect the devices to the 10/100Base-T ports.
7. Plug the DC power supply into the HDMI transmitter unit and switch on.
8.  Power on an HDMI Source and Display to complete the installation.
9.  The LINK Led on the Transmitter and Receiver will illuminate when the HDBaseT Link between the Transmitter and Receiver is established.

Troubleshooting

There is no display on the screen.

•  Check that the DC plug and jack used by external power supply are firmly connected. The Power LED must be lit. If the LED is not lit on Transmitter please check/replace the power supply. If the LED is not lit on Receiver but is lit on the Transmitter please re-check both units by connecting them with a short (~2m) patch cable. If the situation remains please contact LINDY Tech Support.
• Check that the Cat.6/7 cable is plugged in correctly and that both Link Status LED are lit.
• Check that the HDMI source and display are both powered on and active.
• When using the HDBaseT link the local monitor on Transmitter HDMI Bypass port MUST be disconnected!
• Power off all the devices, then power on in this order: first, the Transmitter unit, then the display and finally the HDMI source.
•  For several HDMI devices it may be helpful to unplug and re-plug their HDMI connection to re-initiate the HDMI handshake and recognition.
• Reduce the length of Cat.6/7 or HDMI cable used, or use a higher quality cable.

CE/FCC Statement

CE Certification
LINDY declares that this equipment complies with relevant European CE requirements.
UKCA Certification
LINDY declares that this equipment complies with relevant UKCA requirements.

FCC Certification

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.You are cautioned that changes or modifications not expressly approved by the party responsible for compliance could void your authority to operate the equipment.This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

1.  This device may not cause harmful interference, and
2.  This device must accept any interference received, including interference that may cause undesired operation. The enclosed power supply has passed Safety test requirements, conforming to the US American versions of the International Standard IEC 60950-1 or 60065 or 62368-1.

Recycling Information

Europe, United Kingdom
In 2006 the European Union introduced regulations (WEEE) for the collection and recycling of all waste electrical and electronic equipment. It is no longer allowable to simply throw away electrical and electronic equipment. Instead, these products must enter the recycling process.Each individual EU member state has implemented the WEEE regulations into national law in slightly different ways. Please follow your national law when you want to dispose of any electrical or electronic products. More details can be obtained from your national WEEE recycling agency.

References

• Lindy Electronics

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>