LiGHTPRO 181S 12V Avior Dimmable 16W Flood Light User Manual
- June 3, 2024
- LiGHTPRO
Table of Contents
LiGHTPRO 181S 12V Avior Dimmable 16W Flood Light
Thank you for purchasing the Lightpro Avior.
This document contains the required information for correct, efficient, and
safe use of the product. Consult the general manual of the Lightpro 12-volt
system and the user manual of your transformer for more information about the
set up and connection of your light plan. Read the information in this manual
carefully before using the product. Keep this manual near the product for
consultation in the future.
PRODUCT DESCRIPTION
The Lightpro Avior is an LED spot for outdoor use. The fixture can be installed on a fixed underground with the included screws, or be placed in the ground with the included spike. This product may only be used as outdoor lighting in combination with the Lightpro 12-volt system. Any alterations made to the product may have consequences for the safety, warranty, and correct functioning of the product and/or other parts of the system.
Specifications
- Product Lightpro Avior
- Article number 181S
- Power (max.) 16W
- Luminous flux 150 – 1500 lm
- Dimensions (H x W x D) 125 x 180 x 68 mm
- Protection class IP44
- Ambient temperature -20°C to 50°C
- Cable length 1m
- Dimmable Yes, with built-in dim
INSTALLATION
Packaging content
[Figure A]
- Fixture Avior
- Ground spike
- Screws
- Plugs
- Lightpro connector
- Hex key
Check if all parts are present in the packaging. For questions about parts, service, and any complaints or other remarks, you can always contact us. E-mail: info@lightpro.nl
Option 1: placement on a fixed underground or mounting to a wall [Figure B]
- Remove the screw from the base using the included hex key (Figure A [6]).
- Remove the fixture from the base.
[Figure C]
• Install the base onto the underground with the included screws.
If necessary, drill a hole in the underground and use the included plugs.
[Figure D]
- Place the fixture in the base.
- Place the screw in the base.
- Put the fixture in the desired position.
- Fasten the screw using the included hex key
(Figure A [6])
Option 2: placement in the ground
[Figure E]
- Place the spike underneath the base.
- Properly fasten the spike.
- Put the fixture in the desired position.
- Fasten the screw using the included hex key
(Figure A [6]).
5. Place the fixture in the ground.
DIMMER FUNCTION
The fixture is equipped with a built-in dimmer. The light output can be set to
6 different levels.
[Figure F]
Push the button to set the desired light output
INSTALLATION OF THE LIGHTS
- Install the products in the desired position and lay the cables so they can be comfortably connected to the transformer or main cable.
- If products are provided with a drain hole for water, this hole must be pointing downwards.
- Use non-corrosive fixing materials (supplied as standard) if you want to bolt the products down.
- Connect the lights to the main cable by using the connector as shown in figure [G].
- Consult the manual of your transformer for more information.
MAINTENANCE
- Always fit this product so that it can still be accessed for servicing or maintenance. This product must not be permanently embedded or bricked in.
- Turn off the system by pulling the plug of the transformer from the socket for maintenance.
- Regularly clean the product with a soft, clean cloth. Avoid abrasives that can damage the surface.
- Clean products with stainless steel parts with a stainless steel cleaning agent once per six months.
- Do not use a high pressure washer or aggressive chemical cleaning agents when cleaning the product. This can cause irreparable damage
Discarded electrical equipment must not be put in the household waste. If possible, take it to a recycling company. For details of recycling, contact a municipal waste processing company or your dealer.
For questions about parts, service, any complaints or other matters, you can contact us at any time. E-mail: info@lightpro.nl
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>