LiGHTPRO Juno-4 194S Outdoor Garden Light User Manual
- June 9, 2024
- LiGHTPRO
Table of Contents
LiGHTPRO Juno-4 194S Outdoor Garden Light User Manual
Thank you for purchasing the Lightpro Juno. This document contains the required information for correct, efficient and safe use of the product. Consult the general manual of the Lightpro 12-volt system and the user manual of your transformer for more information about the set up and connection of your light plan.
Read the information in this manual carefully before using the product. Keep this manual near the product for consultation in the future.
PRODUCT DESCRIPTION
The Lightpro Juno is a standing LED lamp for outdoor use. The fixture can be mounted on a solid surface or placed in the ground with the supplied spikes. This product may only be used as outdoor lighting in combination with the Lightpro 12-volt system. Any alterations made to the product may have consequences for the safety, guarantee and correct functioning of the product and/or other parts of the system.
SPECIFICATIONS
Product Lightpro Juno 2 / 4
Article number 193S / 194S
Light source LED 2 / 4 W AC/DC 12V
Power (max) 2 / 4 W
Luminous flux (max) 192 / 372 lm
Light colour 3.000K
Average lifetime 25.000
Dimensions (h x Ø) 85 x 55 x 68 mm
Protection class IP65
Ambient temperature -20°C to 50°C
Cable length 2m
Dimmable No
Light source Not replaceable
On/off 10.000
INSTALLATION
Packaging content [Figure A]
- Fixture Juno
- Baseplate
- Screw
- Screw
- Spike
- Screws
- Plugs
- Lightpro connector
- Hex key
Check if all parts are present in the packaging. For questions about parts, service, and any complaints or other remarks, you can always contact us. E-mail: info@lightpro.nl
Option 1: Placement on a fixed underground [Figure B]
Mount the base [2] on the surface with the included screw [6].
If necessary, drill a holes in the underground and use the included plug [7].
Option 2: Placement in the ground [Figure C]
Mount the base [2] on the spike [5] with the included screw [4].
[Figure D]
- Attach the fixture [1] to the foot [2] with the screw [3].
- Set the fixture to the desired position.
- Fasten the screw [3] using the included hex key [9].
[Figure E]
- Attach the fixture [1] to the base [2] with the screw [3].
- Set the fixture to the desired position.
- Fasten the screw [3] using the included hex key [9].
[Figure F]
Ready
[Figure G]
Place the fixture in the ground.
Just twist and connect!
INSTALLATION OF THE LIGHTS
- Install the products in the desired position and lay the cables so they can be comfortably connected to the transformer or main cable.
- If products are provided with a drain hole for water, this hole must be pointing downwards.
- Use non-corrosive fixing materials (supplied as standard) if you want to bolt the products down.
- Connect the lights to the main cable by using the connector as shown in figure on page 5.
- Consult the manual of your transformer for more information.
SAFETY
- Always fit this product so that it can still be accessed for servicing or maintenance. This product must not be permanently embedded or bricked in.
- Turn off the system by pulling the plug of the transformer from the socket for maintenance.
- Regularly clean the product with a soft, clean cloth. Avoid abrasives that can damage the surface.
- Clean products with stainless steel parts with a stainless steel cleaning agent once per six months.
- Do not use a high pressure washer or aggressive chemical cleaning agents when cleaning the product. This can cause irreparable damage.
- Protection class III: this product may only be connected to safety extra-low voltage up to a maximum of 12 Volt.
- This product is suitable for outside temperatures of: -20 to 50°C.
- Do not use this product in areas where combustible gases, fumes or liquids may be stored.
This product meets the EU standards for health, safety and environmental protection.
For questions about parts, service, any complaints or other matters, you can contact us at any time. E-mail: info@lightpro.nl
Discarded electrical equipment must not be put in the household waste. If possible, take it to a recycling company. For details of recycling, contact a municipal waste processing company or your dealer.
5 year warranty – visit our website at lightpro.nl for warranty conditions.
UK Authorised Representative
(for authorities only)
ProductIP (UK) Ltd.
8, Northumberland Av.
London WC2N 5BY
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>