LiGHTPRO 187U Atik R2 Dimmable Ground Light User Manual

LiGHTPRO 187U Atik R2 Dimmable Ground Light

Thank you for purchasing the Lightpro Atik R2.
This document contains the required information for correct, efficient, and safe use of the product. Consult the general manual of the Lightpro 12-volt system and the user manual of your transformer for more information about the set up and connection of your light plan.

Read the information in this manual carefully before using the product. Keep this manual near the product for consultation in the future.

PRODUCT DESCRIPTION

The Lightpro Atik R2 is an LED spot for outdoor use.
The fixture can be installed in a fixed underground with the included screws, or be placed in the ground with the included ground tube. This product may only be used as outdoor lighting in combination with the Lightpro 12-volt system. Any alterations made to the product may have consequences for the safety, guarantee, and correct functioning of the product and/or other parts of the system.

Specifications

INSTALLATION

Packaging content

[Figure A]

1. Fixture Atik R2
2. Ground tube
3. Lightpro connector
4. Alternative reflector

Check if all parts are present in the packaging. For questions about parts, service, and any complaints or other remarks, you can always contact us. E-mail: info@lightpro.nl

Option 1: placement in de ground

[Figure B]

1. Place the ground tube in the ground.
2. Place the fixture in the ground tube.

The push button for setting the built-in dimmer is located at the underside of the fixture. To control the dimmer, the fixture has to be (temporarily) removed from the ground tube. When installing, sufficient cable length has to be reserved to be able to reach the dimmer.

Option 2: placement in a fixed underground

[Figure C]

1. Drill a hole (Ø100 mm) in the underground.
2. Place the fitting in the drilled hole. The ground tube does not need to be used.

ADJUSTING BEAM DIRECTION AND/OR CHANGING THE REFLECTOR

The pre-installed reflector has a beam angle of 60°.
If desired, it can be replaced by the included alternative reflector, which has a beam angle of 23°

[Figure D]

1. Unscrew the cover ring.
2. Remove the cover ring from the fixture

[Figure E]

1. Unscrew the reflector.
2. Remove the reflector.
3. Place the alternative reflector (Figure A [4]).
4. Fasten the reflector.

[Afbeelding F] The light source is secured in place by a spring mechanism.

1. Pull the light source holder away from the fixture, putting tension on the spring.
2. Keep the spring in tension, and move the holder of the light source to the desired position.

[Afbeelding G]

1. Place the cover ring on the fixture.
2. Properly fasten the cover ring.

DIMMER FUNCTION

**** The fixture is equipped with a built-in dimmer. The light output can be set to 6 different levels.

[Figure H]

• Push the button to set the desired light output.

INSTALLATION OF THE LIGHTS

• Install the products in the desired position and lay the cables so they can be comfortably connected to the transformer or main cable.

• If products are provided with a drain hole for water, this hole must be pointing downwards.

• Use non-corrosive fixing materials (supplied as standard) if you want to bolt the products down.

• Connect the lights to the main cable by using the connector as shown in figure [I].
  

• Consult the manual of your transformer for more information.

MAINTENANCE

• Always fit this product so that it can still be accessed for servicing or maintenance. This product must not be permanently embedded or bricked in.
• Turn off the system by pulling the plug of the transformer from the socket for maintenance.
• Regularly clean the product with a soft, clean cloth. Avoid abrasives that can damage the surface.
• Clean products with stainless steel parts with a stainless steel cleaning agent once per six months.
• Do not use a high pressure washer or aggressive chemical cleaning agents when cleaning the product. This can cause irreparable damage.

| Discarded electrical equipment must not be put in the household waste. If possible, take it to a recycling company. For details of recycling, contact a municipal waste processing company or your dealer.
---|---
| 5 year warranty – visit our website at lightpro.nl for warranty conditions
| For questions about parts, service, any complaints or other matters, you can contact us at any time. E-mail: info@lightpro.nl

References

• Lightpro
• Lightpro

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>