VIVO STAND-V012K Dual Monitor Arm Extra Tall Mount Instruction Manual

: June 14, 2024
: Vivo

Table of Contents

VIVO STAND-V012K Dual Monitor Arm Extra Tall Mount
Product Information
Product Usage Instructions
ASSEMBLY STEPS
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

VIVO STAND-V012K Dual Monitor Arm Extra Tall Mount

Product Information

Specifications

SKU : STAND-V012K,W
Weight Capacity: 2.2-19.8lbs (1-9kg) per monitor

Product Usage Instructions

Package Contents

A (x2) Arm
B (x1) Clamp
C (x2) VESA Plate
D (x1) Top Pole
E (x1) Bottom Pole
F (x1) Pole Cap
M (x1) Soft Pad
G (x1) Pole Connector
H (x2) Cable Clip
I (x1) Grommet Base
J (x1) Support Plate
M-A (x8) M4x12 Screw
M-F (x8) Spacer
T-C (x1) 6mm Allen Wrench
M-B (x8) M4x16 Screw
S-A (x2) M6x10 Thumbscrew
M-C (x8) M5x12 Screw
S-B (x3) M6x16 Screw
M-D (x8) M5x16 Screw
T-A (x1) 3mm Allen Wrench
M-E (x8) D5 Washer
T-B (x1) 4mm Allen Wrench

Tools Needed

Phillips Screwdriver

Assembly Steps

Step 1
Insert Pole Cap (F) into the top of Top Pole (D).
Step 2
Loosen the screws and disassemble the Clamp (B) and separate into Clamp Brace (B1) and Clamp (B2) using 4mm Allen Wrench (T-B).

Step 3

Option A: Clamp Installation
Attach Clamp Brace (B1) to Bottom Pole (E).

Option B: Grommet Installation
For grommet hole attachment only, cut Soft Pad (M) along the indentations. Peel the protective film off of Soft Pad (M) and place it onto Clamp Brace Base (I) as shown below. If not using an existing through-hole, using a 10mm drill bit, drill through the desktop at least 2″ away from the edge. Set aside all parts except for Clamp Bolt (B3).

Step 4
Slide Cable Clip (H) and Arm (A) onto Bottom Pole (E). Tighten Arm (A) using 6mm Allen Wrench (T-C).
Step 5
Attach Top Pole (D) to Bottom Pole (E) using Pole Connector (G). Once poles are fully threaded on, tighten set screws on Pole Connector (G) using 3mm Allen Wrench (T-A). Slide Cable Clip (H) and Arm (A) onto Top Pole (D). Tighten Arm (A) using 6mm Allen Wrench (T-C).
Step 6
Attach VESA Plates (C) to the back of the monitors using Screws (M-A through M-D) and Washers (M-E). If needed, use Spacers (M-F).
Step 7
Slide VESA Plates (C) with monitors onto the Arms (A).

FAQ

Q: What is the weight capacity of this desk mount?
A: The weight capacity of this desk mount is 2.2-19.8lbs (1-9kg) per monitor.
Q: Do I need any additional tools for assembly?
A: Yes, you will need a Phillips screwdriver.
Q: Can I use this desk mount for children’s monitors?
A: No, this desk mount is not suitable for children’s monitors. It contains small parts that may pose a choking hazard and is not recommended for children under 3 years. Adult supervision is required.

SKU: STAND-V012K,W
Scan the QR code with your mobile device or follow the link for helpful videos and specifications related to this product.

https://vivo-us.com/products/stand-v012k

GET IN TOUCH | Monday-Friday from 7:00am-7:00pm CST

help@vivo-us.com
www.vivo-us.com Chat live with an agent!
309-278-5303

WARNING!
If you do not understand these directions, or if you have any doubts about the safety of the installation, please call a qualified technician. Check carefully to make sure there are no missing or defective parts. Improper installation may cause damage or serious injury. Do not use this product for any purpose that is not explicitly specified in this manual. Do not exceed weight capacity.
We cannot be liable for damage or injury caused by improper mounting, incorrect assembly or inappropriate use.

TIPOVER WARNING
SERIOUS OR FATAL CRUSHING INJURIES CAN OCCUR FROM TIPOVER. TO HELP PREVENT TIPOVER:

NEVER ALLOW CHILDREN TO CLIMB, STAND, HANG, OR PLAY ON ANY PART OF MONITOR OR STAND.
USE TIPOVER RESTRAINT OR ANCHOR STAND TO WALL
USE OF TIPOVER RESTRAINTS MAY ONLY REDUCE, BUT NOT ELIMINATE RISK OF TIPOVER.

WARNING: CHOKING HAZARD
SMALL PARTS – NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.

PACKAGE CONTENTS

NOTE: SOME HARDWARE INCLUDED MAY NOT BE USED

TOOLS NEEDED

DO NOT EXCEED WEIGHT CAPACITY. Failure to do so may result in serious injury.

ASSEMBLY STEPS

STEP 1 Insert Pole Cap (F) into the top of Top Pole (D).
STEP 2 Loosen the screws and disassemble the Clamp (B) and seperate into Clamp Brace (B1) and Clamp (B2) using 4mm Allen Wrench (T-B).
STEP 3
- OPTION A: Clamp Installation
  Attach Clamp Brace (B1) to Bottom Pole (E) using the M6x16 Screws (S-B) and the 4mm Allen Wrench (T-B). Peel the protective film off of Soft Pad (M) and place it onto Clamp Brace (B1). For thinner desktops, re-attach the Clamp (B2) to the Clamp Brace (B1) and tighten the screws using the 4mm Allen Wrench (T-B).
  For thicker desktops, disassemble Clamp (B2) using a Phillips screwdriver as shown in 3.1. Flip the L-bracket over and reassemble. Then re-attach Clamp (B2) to Clamp Brace (B1) and tighten the screws using the 4mm Allen Wrench (T-B).
- OPTION B: Grommet Installation
  For grommet hole attachment only, cut Soft Pad (M) along the indentations. Peel the protective film off of Soft Pad (M) and place the pieces onto Grommet Base (I) as shown below. If not using an existing through-hole, using a 10mm (⅜”) drill bit, drill through the desktop at least 2” away from the edge. Disassemble Clamp (B2) using a Philips screwdriver. Set aside all parts except for Clamp Bolt (B3). Attach Bottom Pole (E) and Grommet Base (I) to the desktop using Support Plate (J) and Clamp Bolt (B3) as shown below.
STEP 4 Slide Cable Clip (H) and Arm (A) onto Bottom Pole (E). Tighten Arm (A) using 6mm Allen Wrench (T-C).
STEP 5 Attach Top Pole (D) to Bottom Pole (E) using Pole Connector (G). Once poles are fully threaded on, tighten set screws on Pole Connector (G) using 3mm Allen Wrench (T-A). Slide Cable Clip (H) and Arm (A) onto Top Pole (D). Tighten Arm (A) using 6mm Allen Wrench (T-C).
STEP 6 Attach VESA Plates (C) to the back of the monitors using Screws (M-A through M-D) and Washers (M-E). If needed, use Spacers (M-F).
STEP 7 Slide VESA Plates (C) with monitors over the brackets on Arms (A). Secure using M6x10 Thumbscrews (S-A).
STEP 8 Adjust gas spring support in Arms (A) using 6mm Allen wrench (T-C). Turning counter-clockwise increases support, and clockwise decreases.
STEP 9 Remove cable management covers from underneath Arms (A).
- Manage cables by reattaching the cable management covers to Arm (A) and Cable Clips (H).
STEP 10 Adjust tilt support using 6mm Allen Wrench (T-C).

Love your new VIVO setup and want to share? Tag us in your photo! @vivo_us

LAST UPDATED: 03/21/2023 REV1

Open Monday – Friday 7:00am – 7:00pm CST, our dedicated support team can offer immediate assistance with rapid response times. If any parts are received damaged or defective, please contact us. We are happy to replace parts to ensure you have a fully functioning product.

309-278-5303 AVG. RESOLUTION TIME (within office hrs): 5M 4S

www.vivo-us.com Chat live with an agent! AVG. RESOLUTION TIME (within office hrs): < 15 M
help@vivo-us.com
AVG. RESPONSE TIME (within office hrs): 1HR 8M
- 23% within < 15m
- 38% within < 30m
- 61% within < 1hr
- 83% within < 2hr
- 92% within < 3hr

FOR MORE VIVO PRODUCTS, CHECK OUT OUR WEBSITE AT: www.vivo-us.com