LiGHTPRO 184W Kuma LED Wall Light Fixture User Manual

LiGHTPRO 184W Kuma LED Wall Light Fixture

The system

User manual
Thank you for purchasing the Lightpro Kuma.
This document contains the required information for correct, efficient and safe use of the product. Consult the user manual of your transformer for more information about the installation and connection of your lighting plan or visit our website www.lightpro.nl
Read the information in this manual carefully before using the product. Keep this manual near the product for consultation in the future.

PRODUCT DESCRIPTION

The Lightpro Kuma is an LED wall lamp for outdoor use. The fixture can be mounted on a solid surface or placed in the ground with the supplied spikes. This product may only be used as outdoor lighting in combination with the Lightpro 12-volt system. Any alterations made to the product may have consequences for the safety, guarantee and correct functioning of the product and/or other parts of the system.

SPECIFICATIONS

• Product Lightpro Kuma
• Article number 184W
• Light source LED 6W AC/DC 12V
• Power (max) 6W
• Luminous flux (max) 300 lm
• Light colour 3.000K
• Average lifetime 25.000
• Dimensions (H x Ø) 35 x145 mm
• Protection class IP44
• Ambient temperature -20 °C to 50 °C
• Cable length 3m
• Dimmable No
• Light source Not replaceable
• On/off 10.000

PACKAGING CONTENT

[Figure A]

1. Fixture Kuma
2. Screws
3. Plugs
4. Lightpro connector
5. Hex key
   Check if all parts are present in the packaging. For questions about parts, service, and any complaints or other remarks, you can always contact us.
   E-mail: info@lightpro.nl.

INSTALLATION

[Figure B]

1. Remove the screws from the fixture with the included key (Figure A [5]).
2. Remove the hood from the fixture.

[Figure C]

Optional: Putting the cable through the wall.

1. Drill a hole (Ø10 mm) in the wall for the cable.
2. Open the screw connector in the cable.
3. Put the cable through the hole in the wall.
4. Connect the screw connector in the cable.

[Figure D]

1. Install the back plate with the included screws.
   If necessary, drill holes in the wall and use the included plugs.
   **[Figure E]

**

2. Place the hood over the back plate.
3. Place the screws in the fixture.
4. Fix the hood by fastening the screws with the included key (Figure A [5]).

INSTALLATION OF THE LIGHTS

• Install the products in the desired position and lay the cables so they can be comfortably connected to the transformer or main cable.
• If products are provided with a drain hole for water, this hole must be pointing downwards.
• Use non-corrosive fixing materials (supplied as standard) if you want to bolt the products down.
• Connect the lights to the main cable by using the connector as shown in figure on page 5.
• Consult the manual of your transformer for more information.

SAFETY

• Always fit this product so that it can still be accessed for servicing or maintenance. This product must not be permanently embedded or bricked in.
• Turn off the system by pulling the plug of the transformer from the socket for maintenance.
• Regularly clean the product with a soft, clean cloth. Avoid abrasives that can damage the surface.
• Clean products with stainless steel parts with a stainless steel cleaning agent once per six months.
• Do not use a high pressure washer or aggressive chemical cleaning agents when cleaning the product. This can cause irreparable damage.
• Protection class III: this product may only be connected to safety extra-low voltage up to a maximum of 12 Volt.
• This product is suitable for outside temperatures of: – 20 to 50 °C.
• Do not use this product in areas where combustible gases, fumes or liquids may be stored.

This product meets the EU standards for health, safety and environmental protection.
For questions about parts, service, any complaints or other matters, you can contact us at any time.
E-mail: info@lightpro.nl
Discarded electrical equipment must not be put in the household waste. If possible, take it to a recycling company. For details of recycling, contact a municipal waste processing company or your dealer.
5 year warranty – visit our website at lightpro.nl for warranty conditions.

TECHMAR B.V. | CHOPINSTRAAT 10 | 7557 EH HENGELO | THE NETHERLANDS | WWW.LIGHTPRO.NL\

UK Authorised Representative (for authorities only) ProductIP (UK) Ltd.
8, Northumberland Av. London WC2N 5BY

References

• Lightpro
• Lightpro

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>