LiGHTPRO Quartz 196W Wall Light User Manual
- June 9, 2024
- LiGHTPRO
Table of Contents
LiGHTPRO Quartz 196W Wall Light
Thank you for purchasing the Lightpro Quartz. This document contains the information required for the correct, efficient, and safe use of the product. Please consult the user manual of your transformer for more information on how to set up and connect your light plan, or visit our website: www.lightpro.nl. Before using the product, please read the information in this manual carefully. Keep this manual with the product for future reference.
PRODUCT DESCRIPTION
The Lightpro Quartz is an LED spot for outdoor use. The fixture can be installed in a fixed underground. This product may only be used as outdoor lighting in combination with the Lightpro 12volt system. Any alterations made to the product may have consequences for the safety, guarantee, and correct functioning of the product and/or other parts of the system.
SPECIFICATIONS
- Product: Lightpro Quartz
- Article number: 196W
- Light source: MR11 LED G4 2W AC/DC 12V
- Power (max.): 2W
- Luminous flux: 120 lm
- Beam angle: 30º
- Light colour: 3.000K
- Average lifetime: 25.000
- Dimensions (H x Ø): 105 x 50 x 85 mm (HxBxD)
- Protection class: IP44
- Ambient temperature: 20° C to 50°C
- Cable length: 3m
- Dimmable: No
- Replaceable: Yes
PACKAGING CONTENT
- Fixture Quartz
- Lightpro connector
- Ground Spike
- Screw
- Plug
- Check if all parts are present in the packaging. For questions about parts, service, and any complaints or other remarks, you can always contact us.
- E-mail: info@lightpro.nl
INSTALLATION
Option 1: Ground mounting
- Using a suitable Phillips screwdriver, remove the screw as shown in [1].
- Remove the part from the casing to which the ground pin should be attached [2].
- Now attach the ground pin to the removed part using a suitable Phillips screwdriver and the two screws in the ground pin [3] and [4].
- Place the removed part (see step 1) together with the ground pin back into the casing [6].
- Make sure that the cable runs correctly through the cable entry [5].
Option 2: Wall mounting
- Using the supplied screws (2 pcs), mount the removed part to the wall [7].
- Carefully place the casing on the wall mount. Make sure that the cable runs correctly through the cable entry. For water drainage purposes, the cable should always come out of the Quartz at the bottom [8].
- Secure the casing to the wall mount using the screw [9].
- By slightly loosening the screw, as shown in [10], the spotlight can be rotated to the desired position [11] and [12] for the correct lighting. As the spot is in the correct position, this screw needs to be tightened again.
NB
If desired, the cable can be fed through the wall. Drill a 10 mm hole in the
desired position through the wall with a suitable drill. Feed the small plug
with the cable through the drilled hole. Fit the plug to the appropriate cable
with the appropriate female plug [13].
Option 3: Light source replacement
- Using a suitable Phillips screwdriver, remove the two screws, as shown in [13].
- Now carefully pull out the lamp holder and remove the old light source [14].
- Place a new light source in the holder. Please note; Only use the specified light source [15].
- Place the lamp holder back into the casing [16] and [17]. Please note: Put the rubber ring back in the correct position. There should be no foreign objects between the rubber ring and the casing.
- Install the lamp holder in the correct position with the corresponding screws [13].
CONNECTION
SCAN
UK Authorised Representative (for authorities only) ProductIP (UK) Ltd. 8, Northumberland Av. London WC2N 5BY
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>