HALO RL4 Smart Wi-Fi LED Downlight Instructions
- June 3, 2024
- HALO
Table of Contents
RL4 Smart Wi-Fi LED Downlight
Instructions
PACKAGING CONTENTS
| A. LED module
---|---
| B. Socket Adapter (E26)
For retrofit only. Not included with -CA version
| C. #8-32 Self-tapping screw (included)
| D. #8-32 Screw (included)
| E. #8-32 Hex Nut (included)
ITEMS REQUIRED (Purchase separately)
- Philips Screwdriver
- Gloves
IMPORTANT SAFETY INSTRUCTIONS
When using the product, basic precautions should always be followed, including the following:
- Heed all warnings, including the below warnings AND those included on the product.
- HALO™ recessed luminaires (fixtures) are designed to meet the latest NEC requirements and are certified in full compliance with UL. Before attempting the installation of any recessed lighting luminaire checks your local electrical code. This code sets the wiring standards for your locality and should be carefully studied before starting.
- Read and follow these instructions.
- Do not make or alter any open holes in an enclosure of wiring or electrical components during kit installation.
- To prevent wiring damage or abrasion, do not expose wiring to edges of sheet metal or other sharp objects.
- Connect the fixture to a 120-volt, 60 Hz power source. Any other connection voids the warranty.
- Fixture should be installed by persons with experience in household wiring or by a qualified electrician. The electrical system, and the method of electrically connecting the fixture to it, must be in accordance with the National Electrical Code and local building codes.
- WARNING – Risk of fire or electric shock. Install this kit only in luminaires that have the construction features and dimensions shown in the photographs and/or drawings and where the input rating of the retrofit kit does not exceed the input rating of the luminaire.
WARNING
Risk of Fire – MINIMUM 90°C SUPPLY CONDUCTORS. If uncertain, consult an
electrician.
Risk of Electric Shock To avoid possible electrical shock, be sure that
power supply is turned off at fuse box or circuit breaker before installing
orservicing the luminaire.
WARNING
Risk of Fire/Electric Shock – LED Retrofit Kit installation requires
knowledge of luminaires’ electrical systems. If not qualified, do not attempt
installation. Contact a qualified electrician. Luminaire wiring and electrical
parts may be damaged when drilling for the installation of an LED retrofit
kit. Check for enclosed wiring and components.
WARNING
Risk of Fire/Electric Shock
- LED connector is compatible with Halo 4” H245, H995, H99, H450 Series LED Housings
- LED connector meets California Title-24 high-efficacy luminaire standard as a non-screw base socket.
- LED connector is a non-screw-base luminaire disconnect for toolless installation.
CAUTION
Edges may be Sharp – Wear gloves while handling.
FCC STATEMENT
FCC Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
- This device may not cause harmful interference.
- This device must accept any interference received, including interference that may cause undesired operation.
Note: The grantee is not responsible for any changes or modifications not
expressly approved by the party responsible for compliance. Such modifications
could void the user’s authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation.
This equipment generates uses and can radiate radio frequency energy and, if
not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment
does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try
to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and the receiver.
- Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help
RF Exposure Statement
- This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20 cm between the radiator and your body.
IC Statement
- This device contains license-exempt transmitter(s)/receiver(s) that comply with Innovation, Science, and Economic Development Canada’s license-exempt RSS(s). Operation is subject to the following two conditions: (1) This device may not cause interference. (2) This device must accept any interference, including interference that may cause undesired operation of the device.
- This device complies with ISED ICES Standard Canada ICES-005(B) / NMB-005 (B)
IC 20cm RF
- This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20 cm between the radiator and your body.
- This device complies with Industry Canada license-exempt RSS-247 standard(s).
- This equipment complies with FCC & IC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20 cm between the radiator and your body.
- Do not make or alter any open holes in an enclosure of wiring or electrical components during kit installation.
- This device complies with Industry Canada’s license-exempt RSS. Operation is subject to the following two conditions:
– (1) This device may not cause interference; and
– (2) This device must accept any interference, including interference that may cause undesired operation of the device.
FCC ID – 2AC7Z-ESP32SOL01
IC Code – 21098-ESP32SOL01
SAVE THESE INSTRUCTIONS AND WARNINGS.
5-YEAR WARRANTY
THE FOLLOWING WARRANTY IS EXCLUSIVE AND IN LIEU OF ALL OTHER WARRANTIES,
WHETHER EXPRESS, IMPLIED, OR STATUTORY INCLUDING, BUT NOT LIMITED TO, ANY
WARRANTY OF MERCHANTABILITY OR FITNESS FOR ANY PARTICULAR PURPOSE.
Cooper Lighting Solutions warrants to customers that, for a period of FIVE
years from the date of purchase, Cooper Lighting Solutions products will be
free from defects in materials and workmanship. The obligation of Cooper
Lighting Solutions under this warranty is expressly limited to the provision
of replacement products. This warranty is extended only to the original
purchaser of the product. A purchaser’s receipt or other proof of the date of
original purchase is acceptable to Cooper Lighting Solutions. This is required
before warranty performance shall be rendered.
This warranty does not apply to Cooper Lighting Solutions products that have
been altered or repaired or that have been subjected to neglect, abuse,
misuse, or accident (including shipping damages). This warranty does not apply
to products not manufactured by Cooper Lighting Solutions which have been
supplied, installed, and/or used in conjunction with Cooper Lighting Solutions
products. Damage to the product caused by replacement bulbs or corrosion or
discoloration of brass components is not covered by this warranty.
LIMITATION OF LIABILITY:
IN NO EVENT SHALL Cooper Lighting Solutions BE LIABLE FOR SPECIAL, INDIRECT,
INCIDENTAL, OR CONSEQUENTIAL DAMAGES (REGARDLESS OF
THE FORM OF ACTION, WHETHER IN CONTRACT, STRICT LIABILITY, OR IN TORT
INCLUDING NEGLIGENCE), NOR FOR LOST PROFITS; NOR SHALL THE LIABILITY OF Cooper
Lighting Solutions FOR ANY CLAIMS OR DAMAGE ARISING OUT OF OR CONNECTED WITH
THESE TERMS OR THE MANUFACTURE, SALE, DELIVERY, USE, MAINTENANCE, REPAIR OR
MODIFICATION OF Cooper Lighting Solutions PRODUCTS, OR SUPPLY OF ANY
REPLACEMENT ARTS, THEREFORE, EXCEED THE PURCHASE PRICE OF Cooper Lighting
Solutions PRODUCTS GIVING RISE TO A CLAIM. NO LABOR CHARGES WILL BE ACCEPTED
TO REMOVE OR INSTALL FIXTURES.
All returned products must be accompanied by a Return Goods Authorization
Number issued by the Company and must be returned freight prepaid. Any product
received without a Return Goods Authorization Number from the Company will be
refused.
Cooper Lighting Solutions is not responsible for merchandise damaged in
transit. Repaired or replaced products shall be subject to the terms of this
warranty and are inspected when packed. Evident or concealed damage that is
made in transit should be reported at once to the carrier making the delivery
and a claim filed with them. Do not use any other manufacturer’s dimmers.
Reproductions of this document without the prior written approval of Cooper
Lighting Solutions are strictly prohibited.
NON-SCREW-BASED LED LUMINAIRES
Before proceeding, confirm your recessed housing is compatible with RL4 LED
Retrofit Modules. A list of the most common housings is provided below. Along
with those noted below the RL4 LED Retrofit Modules are UL Certified for use
with any 4” diameter recessed housing constructed of steel or aluminum with an
internal volume that exceeds 42.9 in³. and does not exceed the input rating of
the housing.
• HALO® : H245ICAT, H245RICAT, H99ICAT, H99RTAT, H99TAT, H995ICAT, H995RICAT,
H99T, H99RT, H99ICT, E4ICATSB, E4TATSB, E4RTATSB, H45ICAT, H45RICAT,
H450FR2ICAT
INSTALLATIONS INSTRUCTIONS & MOUNTING
-
For ground connection, attach the preinstalled green ground wire on the light to the housing, using 1 of 3 connection methods:
i. Use sheet metal screw (B) to attach to 1 of 3 slots inside the housing.
ii. Drive pan head screw (C) into the existing hole inside the housing.
Note: If no hole exists, drill a small [1/8”] pilot hole and use the provided #8 sheet metal screw (B).
iii. Twist nut (D) onto the threaded stud in the housing wall.
Note: If no hole exists, drill a small pilot hole and use the provided #8 sheet metal screw.
-
Skip this step if the housing is already equipped with an orange quick connector. If installed:
Remove the mounting bracket and plate from inside the housing and then remove the socket from the plate. Then screw the Socket Adapter (B) into the housing. -
Plug the orange quick connect into the light.
-
Align the module in the center of the housing’s opening. Make sure all wiring is away from the friction clips and press the module firmly up into place.
TIP: After fully inserting the module, twist it clockwise slightly to eliminate any gaps between the ceiling and the trim. -
Setup and Control
DIYers & Homeowners: Configure and control lighting quickly using the WiZ App.
Installers: Use the WiZ Pro Setup App for initial claiming and configuration over Bluetooth and to manage multiple projects. Then control with advanced features using the WiZ Pro Dashboard and WiZ App once Wi-Fi is connected. For more information visit: pro.wizconnected.com
https://app.wizconnected.com/setup
UNINSTALLING
Friction Clips Method
- Twist the fixture (about 60°) counterclockwise to release the grip of the friction clips.
- Pull down firmly on the fixture to remove it from the housing.
- Unplug the orange connector and remove the ground wire.
Cooper Lighting Solutions
1121 Highway 74 South
Peachtree City, GA 30269
P: 770-486-4800
www.cooperlighting.com
© 2022 Cooper Lighting Solutions All Rights Reserved.
Specifications and dimensions are subject to change without notice.
IL518126ML
April 26, 2022 9:48 AM
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>