HALO LA4 Series White Integrated LED Recessed Adjustable Gimbal Trim Instruction Manual

May 15, 2024
HALO

IB518249ML
LA4 Series Instructions

Packaging Contents

HALO LA4 Series White Integrated LED Recessed Adjustable Gimbal Trim -
Packaging ContentsITEMS REQUIRED
(Purchase separately)

  • Screwdriver
  • Gloves
  • Ladder

IMPORTANT SAFETY INSTRUCTIONS

When using product, basic precautions should always be followed, including the following:

  • Heed all warnings, including below warnings AND those included on product.
  • HALO® recessed luminaires (fixtures) are designed to meet the latest NEC requirements and are certified in full compliance with UL. Before attempting installation of any recessed lighting luminaire check your local electrical code. This code sets the wiring standards for your locality and should be carefully studied before starting.

WARNING
Read and follow these instructions.
Risk of Fire – MINIMUM 90°C SUPPLY CONDUCTORS. If uncertain, consult an electrician.
Risk of Electric Shock – To avoid possible electrical shock, be sure that power supply is turned off at fuse box or circuit breaker before installing or servicing luminaire.
Risk of Fire/Electric Shock
Please consult an electrician for installation if uncertain of luminaire electrical systems.

  • Do not make or alter any open holes in an enclosure of wiring or electrical components during kit installation.
  • To prevent wiring damage or abrasion, do not expose wiring to edges of sheet metal or other sharp objects.

CAUTION
Edges may be Sharp – Wear gloves while handling.

  • Connect fixture to a 120 volt, 60 Hz power source. Any other connection voids the warranty.
  • Fixture should be installed by persons with experience in household wiring or by a qualified electrician. The electrical system, and the method of electrically connecting the fixture to it, must be in accordance with the National Electrical
  • Code and local building codes.
  • This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
  • This device complies with ISED ICES Standard Canada ICES-005(B) / NMB-005 (B).
  • Do not make or alter any open holes in an enclosure of wiring or electrical components during kit installation.
  • Please examine all parts that are not intended to be replaced by the retrofit kit for damage and replace any damaged parts prior to installation of the retrofit kit.
  • This device is not intended for use with emergency exits.
  • For Canada only per CSA C22.2 No. 250.1-16, retrofits for luminaire conversion: The retrofit kit is accepted as a component of a luminaire where the suitability of the combination shall be determined by authorities having jurisdiction. Product must be installed by a qualified electrician in accordance with the applicable and appropriate electrical codes. The installation guide does not supersede local or national regulations for electrical installations

SAVE THESE INSTRUCTIONS AND WARNINGS.
NON-SCREWBASE LED LUMINAIRES
WARNING

Risk of Fire/Electric Shock –

  • LED connector is compatible with Halo 4” H995 and Halo H245 Series LED luminaires.
  • LED connector meets California Title-24 and Washington State high-efficacy luminaire standard as a non-screw base socket.
  • LED connector is a non-screwbase luminaire disconnect for tool-less installation.

The LA4 is UL Certified for use with any 4” diameter recessed luminaire constructed of steel or aluminum with an internal volume that exceeds 62.3” in³ addition to those noted below and does not exceed the input rating of the luminaire:
HALO®: H99ICAT, H99RTAT, H99TAT, H995ICAT, H995RICAT, H99T, H99RT, H99ICT, H245ICAT, H245RICAT
For additional information, please refer to the latest Halo LED Specification sheet found at www.cooperlighting.com
DIMMING
The Halo LED luminaire can be dimmed with phase-control dimmers (leading edge and trailing edge phase cut). Refer to product specifications and dimming information at www.cooperlighting.com; and consult the dimmer manufacturer for their latest dimmer listings, load ratings and product information.

WIRE INSTALLATION

Before proceeding, confirm luminaire is compatible with LA4. A listing of the most common luminaires are provided in the Recessed Luminaires section of these instructions.
HALO LA4 Series White Integrated LED Recessed Adjustable Gimbal Trim -
figure

GROUND WIRE INSTALLATION

Note:Ground wire must be securely installed to the housing. Three connection methods shown below.

  1. For ground connection from LED module to housing, use provided green ground wire (factory installed) as shown in (Fig. 1).
  2. Connect other end of ground wire to housing.
    Connection to housing may vary depending on model. Three connection methods are described below.
  • Use existing screw inside housing (Fig. 2).
  • Use supplied #8 nut (E) on existing stud (Fig. 3).
  • Use supplied #8-32 screw (D) in existing hole (Figure 4).

Note: If no hole exist, drill a hole and use supplied #8 sheet metal screw (C); connect to new hole (Figure 4).
WARNING
Risk of Fire/Electric Shock –
Use caution when drilling holes, luminaire wiring and electrical parts may be damaged.

RETROFIT INSTALLATION INTO E26 EDISON SCREW BASE RECESSED LUMINAIRE

Note:Confirm housing is compatible with LA4 LED retrofit. A listing of the most common luminaires is provided in the RECESSED LUMINAIRES section of these instructions.

  1. Remove mounting bracket and plate from inside existing recessed housing (if installed).
  2. Remove socket from plate (if installed).
  3. Screw Edison base adapter (B) into existing Edison base socket in housing (Figure 5).
  4. Plug orange connector on LA4 LED module (A) into the orange connector on the screw base adapter (B) (Figure 5).
  5. While wearing gloves, squeeze friction blades together and install into recessed housing (Figure 6).
  6. Carefully route wires into fixture and push module up flush to ceiling surface.

HALO LA4 Series White Integrated LED Recessed Adjustable Gimbal Trim -
figure 1 INSTALLATION INTO HALO® H995X SERIES LED (NON-SCREW BASE) HOUSINGS

Note: Compliant with energy codes requiring nonscrew base sockets.

  1. Plug module into Halo recessed fixture  connector (Figure 7).
  2. While wearing gloves, squeeze friction blades together and install into recessed housing (Figure 6).
  3. Carefully route wires into fixture and push module up flush to ceiling surface.

REPLACING LED MODULE

  1. With fingertips, pull down firmly on trim ring until module is removed from the housing.
  2. Disconnect LED module wiring from recessed can (LED connector or screw-in Edison base).
  3. Remove ground wire from housing.

5-YEAR LIMITED WARRANTY

THE FOLLOWING WARRANTY IS EXCLUSIVE AND IN LIEU OF ALL OTHER WARRANTIES, WHETHER EXPRESS, IMPLIED OR STATUTORY INCLUDING, BUT NOT LIMITED TO, ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR ANY PARTICULAR PURPOSE.
Cooper Lighting Solutions warrants to customers that, for a period of five years from the date of purchase, Cooper Lighting Solutions products will be free from defects in materials and workmanship. The obligation of Cooper Lighting Solutions under this warranty is expressly limited to the provision of replacement products. This warranty is extended only to the original purchaser of the product. A purchaser’s receipt or other proof of date of original purchase acceptable to Cooper Lighting Solutions. This is required before warranty performance shall be rendered.
This warranty does not apply to Cooper Lighting Solutions products that have been altered or repaired or that have been subjected to neglect, abuse, misuse or accident (including shipping damages). This warranty does not apply to products not manufactured by Cooper Lighting Solutions which have been supplied, installed, and/or used in conjunction with Cooper Lighting Solutions products. Damage to the product caused by replacement bulbs or corrosion or discoloration of brass components are not covered by this warranty.

LIMITATION OF LIABILITY:

IN NO EVENT SHALL COOPER LIGHTING SOLUTIONS BE LIABLE FOR SPECIAL, INDIRECT, INCIDENTAL, OR CONSEQUENTIAL DAMAGES (REGARDLESS OF THE FORM OF ACTION, WHETHER IN CONTRACT, STRICT LIABILITY, OR IN TORT INCLUDING NEGLIGENCE), NOR FOR LOST PROFITS; NOR SHALL THE LIABILITY OF COOPER LIGHTING SOLUTIONS FOR ANY CLAIMS OR DAMAGE ARISING OUT OF OR CONNECTED WITH THESE TERMS OR THE MANUFACTURE, SALE, DELIVERY, USE, MAINTENANCE, REPAIR OR MODIFICATION OF COOPER LIGHTING SOLUTIONS PRODUCTS, OR SUPPLY OF ANY REPLACEMENT PARTS THEREFORE, EXCEED THE PURCHASE PRICE OF COOPER LIGHTING SOLUTIONS PRODUCTS GIVING RISE TO A CLAIM. NO LABOR CHARGES WILL BE ACCEPTED TO REMOVE OR INSTALL FIXTURES.
All returned products must be accompanied by a Return Goods Authorization Number issued by the Company and must be returned freight prepaid. Any product received without a Return Goods Authorization Number from the Company will be refused.

Cooper Lighting Solutions is not responsible for merchandise damaged in transit. Repaired or replaced products shall be subject to the terms of this warranty and are inspected when packed. Evident or concealed damage that is made in transit should be reported at once to the carrier making the delivery and a claim filed with them.
Reproductions of this document without prior written approval of Cooper Lighting Solutions are strictly prohibited.

FCC Statement

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off an on, the user is encouraged to try to correct the interference by one or more of the following measures:

  • Reorient or relocate the receiving antenna.
  • Increase the separation between the equipment and receiver.
  • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
  • Consult the dealer or an experienced radio/TV technician for help.

Any changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

Cooper Lighting Solutions
1121 Highway 74 South
Peachtree City, GA 30269
P:770-486-4800
www.cooperlighting.com
© 2020 Cooper Lighting Solutions
All Rights Reserved
Printed in China
Publication No. IB518249ML
Cooper Lighting Solutions is a registered trademark.
All trademarks are property of their respective owners.
Product availability, specifications, and compliances are subject to change without notice

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals