Prime1500 Outdoor Pellet Grill

Product Information: HALO Prime1500 Pellet Grill

The HALO Prime1500 Pellet Grill is a pellet-burning appliance that requires proper installation and use to avoid any property damage, bodily injury, or even death. The manufacturer has made every effort to eliminate any sharp edges, but users should still handle all components with care to avoid accidental injury. Before assembly, ensure all parts are present, and if any part is missing or damaged, do not attempt to assemble the appliance. Contact Consumer Service for replacement parts at 1-833-572-1688.

Parts List

Tool Required for Assembly:

• 2 Phillips Screwdriver

Product Usage Instructions

1. Read the entire instruction manual before installation and use of the HALO Prime1500 Pellet Grill.

2. Ensure all parts are present before assembly. If any part is missing or damaged, do not attempt to assemble the appliance. Contact Consumer Service for replacement parts at 1-833-572-1688.

3. Find a large, clean area in which to assemble the grill.

4. Refer to the assembly diagram as necessary.

5. Install the Left-Inner Leg using (3)-M6 x 14mm Screws and install leg cap.

6. Install the Left-Outer Leg using (3)-M6 x 14mm Screws and install leg cap.

7. Install the Left Outer Leg Assembly and Left Inner Leg assembly using pivot bracket 68 & 69A, (2)-M6 x 2.5H x 9.5D shoulder screw, (1)-M6 x 63mm Knob w/ Threaded Shaft and Nylon-Spacer.
   Tighten screws firmly. Set assembly aside.

8. Install the Right-Inner Leg using (3)-M6 x 14 Screws and install leg cap.

9. Install the Right-Outer Leg using (3)-M6 x 14 Screws and install leg cap.

10. Install the Right Outer Leg Assembly and Right Inner Leg assembly using pivot bracket 69 & 69A, (2)-M6 x 2.5H x 9.5D shoulder screw, (1) x 63mm-Knob w/ Threaded Shaft and Nylon-Spacer.
    Tighten screws firmly. Set assembly aside.

WARNING

• “Please read this entire manual before installation and use of this pellet-burning appliance. Failure to follow these instructions could result in property damage, bodily injury, or even death.”
• The manufacturer has made every effort to eliminate any sharp edges. However, you should handle all components with care to avoid accidental injury.
• “READ ALL INSTRUCTIONS BEFORE  INSTALLING AND USING THE APPLIANCE.
• ” “SAVE THESE INSTRUCTIONS.”

CAUTION

• Appliance intended for outdoor use only.
• Unattended cooking leads to cooking fires.
• Improper use can cause uncontrolled fire. To reduce fire risk: use only food-grade 100% natural hardwood pellets.
• This appliance is intended to burn food-grade pellet fuel only.
• Operate only per manufacturer’s instructions.
• Never use gasoline or lighter fluid.
• Always store wood pellets away from heat-producing appliances and other fuel containers.
• Keep the appliance clean – see instruction manual for cleaning and proper operation.
• If fire occurs: call fire department. DO NOT try to move appliance, try to smother fire, or put water on fire.

NOTICE: Before assembly, make sure all parts are present. If any part is missing or damaged, do not attempt to assemble the appliance. Contact Consumer Service for replacement parts at 1-833-572-1688.

NEED MORE INSTRUCTIONS?
Scan for registration, assembly videos, care + use, warranty, recipes, + more.

BATTERY NOT INCLUDED. Requires (1) 12-volt 5Ah Rechargeable Lithium-ion Battery Pack for auger and igniter.

IMPORTANT: Please read all instructions thoroughly before proceeding. Find a large, clean area in which to assemble your HALO Prime1500 Pellet Grill. Please refer to the assembly diagram, as necessary

**Install Left-Inner Leg using (3)-M6 x 14mm Screws and install leg

cap.**

• NOTICE: Make sure all the plastic protection is removed before assembling.

Tool required for assembly: #2 Phillips Screwdriver

ITEM PART DESCRIPTION QTY.

• 63 Leg Cap 1
• 64 Left-Inner Leg-Long 1
• 64A Left-Inner Leg-Short 1
• 82 M6 x 14mm Screw 1

Install Left-Outer Leg using (3)-M6 x 14mm Screws and install leg cap.

ITEM PART DESCRIPTION QTY.

• 63.Leg Cap 1
• 65. Left-Outer Leg-Long 1
• 65 A. Left-Outer Leg-Short 1
• 82. M6 x 14mm Screw 3

Install Left Outer Leg Assembly, Left Inner Leg assembly using pivot bracket 68 & 69A, (2)-M6 x 2.5H x 9.5D shoulder screw, (1)-M6 x 63mm Knob w/ Threaded Shaft and Nylon-Spacer. Tighten screws firmly. Set assembly aside.

ITEM PART DESCRIPTION QTY.

• 68. Pivot Bracket-A 1
• 69 A. Pivot Bracket-C 1
• 78. M6 x 63mm-Knob w/ Threaded Shaft 1
• 79. Nylon Spacer 1
• 80. M6 x 2.5H x 9.5D-Shoulder Screw 2

Install Right-Inner Leg using (3)-M6 x 14 Screws and install leg cap

ITEM PART DESCRIPTION QTY.

• 63. Leg Cap 1
• 66. Right-Inner Leg-Long 1
• 66 A. Right-Inner Leg-Short 1
• 82. M6 x 14mm Screw 3

Install Right-Outer Leg using (3)-M6 x 14 Screws and install leg cap.

ITEM PART DESCRIPTION QTY.

• 63. Leg Cap 1
• 67. Right-Outer Leg-Long 1
• 67 A. Right-Outer Leg-Short 1
• 82. M6 x 14mm Screw 3

Install Right Outer Leg Assembly, Right Inner Leg assembly using pivot bracket 69 & 69A, (2)-M6 x 2.5H x 9.5D shoulder screw, (1) x 63mm -Knob w/ Threaded
Shaft and Nylon- Spacer. Tighten screws firmly. Set assembly aside.

ITEM PART DESCRIPTION QTY.

• 69. Pivot Bracket-B 1
• 69 A. Pivot Bracket-C 1
• 78. M6 x 63 mm Knob w/ Threaded Shaft 1
• 79. Nylon Spacer 1
• 81. M6 x 2.5H x 9.5D-Shoulder Screw 2

Install Front Panel and Rear Brace assembly using (8)-M6 x 14mm screws.

IMPORTANT: Do not tighten screws completely until all screws for this step have been installed.

ITEM PART DESCRIPTION QTY.

• 70. Rear Bracket 1
• 71. Front Panel 1
• 72. RISE ABOVE Logo Plate 1
• 82. M6 x 14mm Screw 8

Attach the Casters using M12 caster wrench.
Mount Casters with Lock to front legs and Mount Swivel casters to rear legs.

NOTE: You can lock the casters that have locks, allowing you to assemble the caster without using a caster wrench.

ITEM PART DESCRIPTION QTY.

• 74. Caster with Lock 2
• 73. Caster-Swivel 2

Attach Brackets-Leg Support-Left and right using 6-M6 x 12 Truss head screws.

ITEM PART DESCRIPTION QTY.

• 61. Bracket-Leg Support-Left 1
• 62. Bracket-Leg Support-Right 1
• 80. M6 x 12 mm Screw6

Turn the cart right up with front casters still in locked position. Attach fire chamber assembly to the “X“ frame using (4) ¼”-20-Knob with Threaded Shaft to secure the cooking chamber in place.

NOTE: We recommend the help of a friend to attach the fire chamber assembly onto the “X” cart frame due to the size and weight.

ITEM PART DESCRIPTION QTY.

• 77. 1/4″-20 x 15mm Knob w/ Threaded Shaft 4

Install cooking grid and warming racks.

ITEM PART DESCRIPTION QTY.

• 5. Warming Rack-Large 1
• 8. Warming Rack-Small 1
• 8. Cooking Grid 1

Step 1. Slide warming rack forward until center support wire is pushed against front section of the bracket.

Step2. Lift up both warming racks then hook the top rack on to the “J” brackets.

Install side table brackets left and right using (12)-M6 x 14mm screws. Install side table left and right using (4)-M6 x 2.5H x 9.5D-Shoulder Screw.

ITEM PART DESCRIPTION QTY.

• Bracket-Side Table-A 2
• Bracket-Side Table-B 2
• Release Spring Pin-Side Table/Cleanout Tray 2
• Side Table-Right 1
• Side Table-Left 1
• “JJ” Tool Hook 2
• M6 x 2.5H x 9.5D-Shoulder Screw 4
• M6 x 14mm Screw 12

1. Install ash tray by pulling the release spring pin, then insert the tray into the tray tracks and slide the tray all the way back. Release the spring pin to lock in place.
2. Insert the leveler into the housing.

Install grease cup with cover.

ITEM PART DESCRIPTION QTY.

• 27. Grease Bucket w/ Cover 1

ASSEMBLED DIMENSIONS

Quick link
” REGISTER YOUR PRIME1500 PRODUCT ASSEMBLY VIDEOS RECIPES + more

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>