Namron

4 kanaler bryter

SKU: 4 kanaler bryter

Quickstart

This is a
secure
Wall Controller
for
CEPT (Europe).

Please make sure the internal battery is fully charged.

Important safety information

Please read this manual carefully. Failure to follow the recommendations in this manual may be dangerous or may violate the law.
The manufacturer, importer, distributor and seller shall not be liable for any loss or damage resulting from failure to comply with the instructions in this manual or any other material.
Use this equipment only for its intended purpose. Follow the disposal instructions.

Do not dispose of electronic equipment or batteries in a fire or near open heat sources.

What is Z-Wave?

Z-Wave is the international wireless protocol for communication in the Smart Home. This
device is suited for use in the region mentioned in the Quickstart section.

Z-Wave ensures a reliable communication by reconfirming every message ( two- way
communication) and every mains powered node can act as a repeater for other nodes
( meshed network ) in case the receiver is not in direct wireless range of the
transmitter.

This device and every other certified Z-Wave device can be used together with any other
certified Z-Wave device regardless of brand and origin as long as both are suited for the
same frequency range.

If a device supports secure communication it will communicate with other devices
secure as long as this device provides the same or a higher level of security.
Otherwise it will automatically turn into a lower level of security to maintain
backward compatibility.

For more information about Z-Wave technology, devices, white papers etc. please refer
to www.z-wave.info.

Product Description

The remote control is a Z-Wave device that can both control other Z-Wave devices and activate scenes inGateways. Although it is controlling other devices, the device cannot act as Z-Wave network controller (primaryor secondary) and will always need a Z-Wave network controller to be included into a Z-Wave network. It alsosupports the Over The Air (OTA) feature for the products firmware upgrade.The remote control has following functions:1. Control of groups of other Z-Wave devices using ‘ON’, ‘OFF’ and Dim commands.2. Activation of scenes in Gateway mode.The encryption modes that the remote control supports are S0, S2 Authenticated, S2 Unauthenticated. Whenthe remote control is being included into a Z-Wave network, you can use your primary controller/gateway toenable one encryption mode or disable encryption. (The primary controller/gateway shall support encryptionmode configuration).

Prepare for Installation / Reset

Please read the user manual before installing the product.

In order to include (add) a Z-Wave device to a network it must be in factory default
state. Please make sure to reset the device into factory default. You can do this by
performing an Exclusion operation as described below in the manual. Every Z-Wave
controller is able to perform this operation however it is recommended to use the primary
controller of the previous network to make sure the very device is excluded properly
from this network.

Inclusion/Exclusion

On factory default the device does not belong to any Z-Wave network. The device needs
to be added to an existing wireless network to communicate with the devices of this network.
This process is called Inclusion.

Devices can also be removed from a network. This process is called Exclusion.
Both processes are initiated by the primary controller of the Z-Wave network. This
controller is turned into exclusion respective inclusion mode. Inclusion and Exclusion is
then performed doing a special manual action right on the device.

Quick trouble shooting

Here are a few hints for network installation if things dont work as expected.

1. Make sure a device is in factory reset state before including. In doubt exclude before include.
2. If inclusion still fails, check if both devices use the same frequency.
3. Remove all dead devices from associations. Otherwise you will see severe delays.
4. Never use sleeping battery devices without a central controller.
5. Dont poll FLIRS devices.
6. Make sure to have enough mains powered device to benefit from the meshing

Association – one device controls an other device

Z-Wave devices control other Z-Wave devices. The relationship between one device
controlling another device is called association. In order to control a different
device, the controlling device needs to maintain a list of devices that will receive
controlling commands. These lists are called association groups and they are always
related to certain events (e.g. button pressed, sensor triggers, …). In case
the event happens all devices stored in the respective association group will
receive the same wireless command wireless command, typically a ‘Basic Set’ Command.

Association Groups:

Group NumberMaximum NodesDescription

1| 5| 1. Send Command Class u0022Device Reset Locally Notification V1u0022 toassociated devices of this group to report factory reset informationwhen factory reset the remote control.2. When remote control battery power value changes, sendCommand Class u0022Battery Report V1u0022 to associated devices of thisgroup to report power value information.3. Short press or press and hold down any button to send sceneactivation command to the associated devices of this group usingCommand Class Central Scene Notification V3
---|---|---
2| 5| Short press / button of Group 2 to send ON/OFF command toassociated devices of this group using Command Class u0022Basic SetV2u0022.Press and hold down / button of Group 2 to send light intensityincrease/decrease command to associated devices of this groupusing Command Class u0022Multilevel V4u0022.
3| 5| Short press / button of Group 3 to send ON/OFFcommand to associated devices of this group usingCommand Class u0022Basic Set V2u0022.Press and hold down / button of Group 3 to sendlight intensity increase/decrease command toassociated devices of this group using Command Classu0022Multilevel V4u0022.
4| 5| Short press / button of Group 4 to send ON/OFFcommand to associated devices of this group usingCommand Class u0022Basic Set V2u0022.Press and hold down / button of Group 4 to sendlight intensity increase/decrease command toassociated devices of this group using Command Classu0022Multilevel V4u0022.
5| 5| Short press / button of Group 5 to send ON/OFFcommand to associated devices of this group usingCommand Class u0022Basic Set V2u0022.Press and hold down / button of Group 5 to sendlight intensity increase/decrease command toassociated devices of this group using Command Classu0022Multilevel V4u0022.

Configuration Parameters

Z-Wave products are supposed to work out of the box after inclusion, however
certain configuration can adapt the function better to user needs or unlock further
enhanced features.

IMPORTANT: Controllers may only allow configuring
signed values. In order to set values in the range 128 … 255 the value sent in
the application shall be the desired value minus 256. For example: To set a
parameter to 200 it may be needed to set a value of 200 minus 256 = minus 56.
In case of a two byte value the same logic applies: Values greater than 32768 may
needed to be given as negative values too.

Parameter 1: factory reset

Value=0x55AA, other values are invalid,factory reset the Remote Control
Size: 2 Byte, Default Value: 0

SettingDescription

Technical Data

Supported Command Classes

• Association Grp Info
• Association V2
• Battery
• Central Scene V3
• Configuration
• Device Reset Locally
• Firmware Update Md V4
• Manufacturer Specific V2
• Multi Channel Association V3
• Powerlevel
• Security
• Security 2
• Supervision
• Transport Service V2
• Version V2
• Wake Up V2
• Zwaveplus Info V2

Controlled Command Classes

• Basic
• Switch Multilevel V4

Explanation of Z-Wave specific terms

• Controller — is a Z-Wave device with capabilities to manage the network.
  Controllers are typically Gateways,Remote Controls or battery operated wall controllers.

• Slave — is a Z-Wave device without capabilities to manage the network.
  Slaves can be sensors, actuators and even remote controls.

• Primary Controller — is the central organizer of the network. It must be
  a controller. There can be only one primary controller in a Z-Wave network.

• Inclusion — is the process of adding new Z-Wave devices into a network.

• Exclusion — is the process of removing Z-Wave devices from the network.

• Association — is a control relationship between a controlling device and
  a controlled device.

• Wakeup Notification — is a special wireless message issued by a Z-Wave
  device to announces that is able to communicate.

• Node Information Frame — is a special wireless message issued by a
  Z-Wave device to announce its capabilities and functions.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>