HALO HS-1001-XNA Prime550 Outdoor Pellet Grill

Product Information: HALO Prime550 Pellet Grill

The HALO Prime550 Pellet Grill is a pellet-burning appliance designed for outdoor cooking. It comes with a set of legs that need to be assembled before use. The manufacturer has made every effort to eliminate any sharp edges, but all components should be handled with care to avoid accidental injury. Before assembly, make sure all parts are present. If any part is missing or damaged, do not attempt to assemble the appliance and contact Consumer Service for replacement parts at 1-833-572-1688.

Product Usage Instructions

Before proceeding with the assembly, please read all instructions thoroughly. Find a large, clean area in which to assemble your HALO Prime550 Pellet Grill. Please refer to the assembly diagram, as necessary.

Assembly Instructions

1. Install the Left-Inner Leg using (3) M6 x 14mm Screws and install the leg cap. Use a #2 Phillips Screwdriver as a tool for assembly.
2. Install the Left-Outer Leg using (3) M6 x 14mm Screws and install the leg cap.
3. Install the Left Outer Leg Assembly and Left Inner Leg assembly using pivot bracket 68 & 69A, (2) M6 x 2.5H x 9.5D shoulder screw, (1) M6 x 63mm Knob with Threaded Shaft and Nylon-Spacer. Tighten screws firmly. Set the assembly aside.
4. Install the Right-Inner Leg using (3) M6 x 14 Screws and install the leg cap.
5. Install the Right-Outer Leg using (3) M6 x 14 Screws and install the leg cap.
6. Install the Right Outer Leg Assembly and Right Inner Leg assembly using pivot bracket 69 & 69A, (2) M6 x 2.5H x 9.5D shoulder screw, (1) M6 x 63mm Knob with Threaded Shaft and Nylon-Spacer. Tighten screws firmly. Set the assembly aside.

After the assembly is complete, follow the care and use instructions provided in the manual for safe and effective use of the HALO Prime550 Pellet Grill.

WARNING

• “Please read this entire manual before installation and use of this pellet-burning appliance. Failure to follow these instructions could result in property damage, bodily injury, or even death
• The manufacturer has made every effort to eliminate any sharp edges. However, you should handle all components with care to avoid accidental injury.
• “READ ALL INSTRUCTIONS BEFORE INSTALLING AND USING THE APPLIANCE.”
• “SAVE THESE INSTRUCTIONS.”

CAUTION

• Appliance intended for outdoor use only.
• Unattended cooking leads to cooking fires.
• Improper use can cause uncontrolled fire. To reduce fire risk: use only food-grade 100% natural hardwood pellets.
• This appliance is intended to burn food-grade pellet fuel only.
• Operate only per manufacturer’s instructions.
• Never use gasoline or lighter fluid.
• Always store wood pellets away from heat-producing appliances and other fuel containers.
• Keep the appliance clean – see instruction manual for cleaning and proper operation.
• If fire occurs: call fire department. DO NOT try to move appliance, try to smother fire, or put water on fire.

NOTICE: Before assembly, make sure all parts are present. If any part is missing or damaged, do not attempt to assemble the appliance. Contact Consumer Service for replacement parts at 1-833-572-1688.

NEED MORE INSTRUCTIONS?
Scan for registration, assembly videos, care + use, warranty, recipes, + more.

BATTERY NOT INCLUDED. Requires (1) 12-volt 5Ah Rechargeable Lithium-ion Battery Pack for auger and igniter.
IMPORTANT: Please read all instructions thoroughly before proceeding. Find a large, clean area in which to assemble your HALO Prime550 Pellet Grill. Please refer to the assembly diagram, as necessary

Install Left-Inner Leg using (3)-M6 x 14mm Screws and install leg cap.
NOTICE: Make sure all the plastic protection is removed before assembling.

Tool required for assembly

• 2 Phillips Screwdrive

Assembly Instructions

Install Left-Outer Leg using (3)-M6 x 14mm Screws and install leg cap. ****

Install Left Outer Leg Assembly, Left Inner Leg assembly using pivot bracket 68 & 69A, (2)-M6 x 2.5H x 9.5D shoulder screw, (1)-M6 x 63mm Knob w/ Threaded Shaft and Nylon-Spacer. Tighten screws firmly. Set assembly aside

Install Right-Inner Leg using (3)-M6 x 14 Screws and install leg cap.

Install Right-Outer Leg using (3)-M6 x 14 Screws and install leg cap.

Install Right Outer Leg Assembly, Right Inner Leg assembly using pivot bracket 69 & 69A, (2)-M6 x 2.5H x 9.5D shoulder screw, (1) x 63mm -Knob w/ Threaded Shaft and Nylon- Spacer. Tighten screws firmly. Set assembly aside.

Install Front Panel and Rear Brace assembly using (8)-M6 x 14mm screws.
IMPORTANT: Do not tighten screws completely until all screws for this step have been installed

Attach the Casters using M12 caster wrench.
Mount Casters with Lock to front legs and Mount Swivel casters to rear legs.
NOTE: You can lock the casters that have locks, allowing you to assemble the caster without using a caster wrench

Attach Brackets-Leg Support-Left and right using 6-M6 x 12 Truss head screws

Turn the cart right up with front casters still in locked position. Attach fire chamber assembly to the “X“ frame using (4) ¼”-20-Knob with Threaded Shaft to secure the cooking chamber in place.
NOTE: We recommend the help of a friend to attach the fire chamber assembly onto the “X” cart frame due to the size and weight.

Install cooking grid and warming rack.

Warming rack continued.

Install side table brackets left and right using (12)-M6 x 14mm screws. Install side table left and right using (4)-M6 x 2.5H x 9.5D-Shoulder Screw .

1. Install ash tray by pulling the release spring pin, then insert the tray into the tray tracks and slide the tray all the way back. Release the spring pin to lock in place.
2. Insert the leveler into the housing

Install grease cup with cover.

ASSEMBLED DIMENSIONS

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>