Chargers HSP-C1 Automotive Wireless Charger User Manual
- June 5, 2024
- Chargers
Table of Contents
Chargers HSP-C1 Automotive Wireless Charger
SPECIFICATION AND PACKING LIST
Specification
- Product Name Magnetic wireless car charger
- Charging power 15W10W7.5W 5W
- Effective transmission distance 18 mm
- Product size USB interface: Type C
Packing list
- Wireless car charger x 1
- 1m fast charging cable x 1
- Base clipx1
- User manual x 1
- User card x 1
PRODUCT FUNCTIONS
PARAMETERS
- Model HsP-C1
- Weight: 110g
- Material ABS+ aluminum alloy
- Input Voltage/Current: 9v/2A
- Output Power:15W/10WI7.5W/5W automatic recognition
- Charging power:110.3K-205KHz
- Charging distance:0-8mm
- Compliant standard: Ql Wireless Charging Standard
Supported cell phones
- iPhone12 Mini, iPhone12,
- IPhone12 PRO, IPhone12 PRO Max,
- IPhone13 Mini, iPhone13,
- iPhone13 PRO, IPhone13 PRO Max,
Clip-held width
OPERATING PROCEDURE
- Assemble the base clip into the back of the wireless car charger and fix it to the vehicle air conditioning outlet or other fixed position.
- Insert the USB cable connector into the power input port of the wireless car charger
- Connect the USB charging cable to the vehicle’s USB output port (Qc3.0/PD2.0 protocol support is recommended).
- After the car is started, the LED is lighted in red at first and then flickers in red and blue alternately when in a self-checking state. After self-checking is complete the light tums into red, and the clip keeps open.
- Place the cll phone onto the magnetic surface of the charger, and the clip automatically clamps the phone.
- The cell phone is now being charged, the LED light turns into blue and keeps in breathing light status.
- When need to take the cell phone off just finger-touch the designed position of the charger, the clip will automatically release the phone.
ATTENTION
- This product only works with iPhone 12/13 series cell phones, does not support other cell phone models.
- The Maximum supported charging power is 7.5W, need to use ac3.0 or PD compliant cigarette lighter charging head to achieve this maximum power. The maximum charging power may be 5W after HW upgrade in some conditions.
- To achieve best magnetic force, recommend not to use with phone protective case, or select a protective case thinner than 1.2mm. Another option is to use a magnetic protective case
- You may feel the cell phone is a litte bit hot, iť’s normal and the temperature should be stll under 40’C, the product has an over-heat protection mechanism designed in and will stop charging if temperature reaches 60’C.
- Input power voltage must be lower than 12V.
- Do not squeeze and impact the wireless charger dramaticaly.
- Do not use in super high temperature / high humidity or erosive environment which may damage the cicuit of the wireless charger.
FCC Statement
This device complies with part 15 FCC Rules. Operation is Subject To the following two conditions:(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not explicitly approved by the party responsible for compliance could void the user’s authority to operate thls equipment.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential Installation. This equipment generates, uses and canradate radio frequency energy and, f not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver Is connected.
- Consult the dealer or an experienced radio/TV technician for help.
FCC radiation exposure
The equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. During the operation of the device, a distance of 15 cm surrounding the device and 20 cm above the top surface of the device must be respected.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>