VECLESUS VMST 7 Inch 1080P HD Trailer Wired Backup Camera System User Manual

VECLESUS VMST 7 Inch 1080P HD Trailer Wired Backup Camera System

Components

Safety Information

Usage

• This system is designed to help the driver safely detect people and/or objects to avoid damage or injury. However, you must use it properly. Use of this system is not a substitute for safe, proper or legal driving.
• Never back up/driving while looking at the monitor alone. You should always check behind and around the vehicle when backing up/driving, in the same way as you would if the vehicle did not have the rearview camera system.
• Please, always remember, the area displayed by the rear view camera system is limited. It does not display the entire panorama that is behind you.
• The monitor is not designed to be waterproof. Exposure to water, such as rain, may damage it.

Installation

• Electric shock or product malfunction may occur if this product is installed incorrectly.
• Please use this product within the voltage range(9-36V) specified. Failure to do so can cause electronic shock or product malfunction.
• Take special care when cleaning the monitor.
• Make sure to firmly affix the product before use.
• If smoke or a burning smell is detected, disconnect the system immediately.
• Where the power cable may touch a metal case, cover the cable with a friction tape. A short circuit or disconnected wire may cause a fire.
• While installing the Rear View System be careful with the wire positioning in order to avoid wire damage.
• Do not install the monitor where it may obstruct drivers view or obstruct an air bag device.

Getting Started

Test the system
To ensure the system works properly after installation, all components should be tested and checked before installation.

1. Refer to the component page to check whether the component is missing. We do not rule out that some components may be damaged in the case of violent loading and unloading during transportation. If so, please contact us in time.
2. Connect the power cable(13 pin connector) to the monitor, the positive and negative terminals to 9-36v voltage, then the power button will turn red, press the power button, all the buttons into blue backlight, indicating the successful test of the display, can work normally.
3. Connect 4-pin connector(the other end of the power cable)to the backup camera, restart the power supply of the monitor, and the corresponding channel image will appear (Note: The monitor can only display the image of the camera of the corresponding channel, if your camera is connected to the CH1 channel, please switch the monitor to CHl), If it displays normally, so the backup camera is working properly. If not, please refer to the Troubleshooting.

Before Beginning lnstalltion

• As the camera need to be fixed on the vehicle, it may need to drill a hole on your vehicle, before drilling please measure the size of boreholes and check that no cable or wiring is on the other side of the wall.
• Please clamp all wires securely to reduce the possibility of them being damaged while vehicle is in use.
• Keep all cables away from hot or moving parts and electrical noisy components.

ATTENTION

• Attach camera to bracket using provided screws and adjust the angle.
• Be sure to position the cable properly. The camera cable uses waterproof connectors which means the camera cable can be exposed to all weather elements.
• Do not run the cable over sharp edges, do not kink the cable and keep away from HOT and rotating parts.
• Feed as much cable as possible into vehicle & clamp securely. This reduces the possibility of cable being hooked or snagged.
• Attach monitor to mount, and adjust mounting angle to allow optimum driver viewing comfort.
• The camera system can be wired to be powered “ON” the entire time when the vehicle is on. This is typical in RV and some com- mercial applications.

Installation Guide

System Connection Diagram

Recommended Installation Location

Cable Connections

• RED wire to ignition hot (+) 9-36 volts

• BLACK wire to ground(-) or nagative pole (please use a chassis ground post)

• (Connection Method II) CAM 2

• Green trigger wire is for camera 2(CH2).
  Connects this wire to reverse light hot(+) wire or L========l:11:(]l]I i:t:m:=== backup beeper wire in the fuse box. This connection is needed to activate the CH2 when putting the vehicle into reverse .

• According to your usage, there are different ways to connect the reverse (Green Wire) and video wires(CH1/CH2):

  1. Only one camera and for reversing use: Please connect the camera to CH2, and the green trigger wire to reverse light, at this time, only reversing can activate the monitor.
  2. Only one camera and for monitoring traffic conditions. Please ignore the green trigger wire and connect the camera to any channels, switch to the camera channel through the monitor button to keep the monitor on.
  3. Two cameras (you can buy another camera from us), because CH2 channel can be triggered by the green trigger wire, you can use CH2 as reversing channel, CHl can be used as driving traffic observation channel, you can install the CHl camera on the front door, side door or RV trailer’s rear.

Power Supply

Powered by vehicle fuse box

1.  Find the fuse box under your car cab
2. According to the labels (or car manual) on the fuse hardwire kit to find the power fuse and connect the corresponding trigger wire (voltage must between 9-36V)

Powered by car charger

1. Connect the DCS.5 mm power cord to the car charger, and connect the red and black terminals on the other end to the red and black harness of the power cable respectively.
2. Use electrical tape to seal the exposed copper wire to prevent leakage and short circuit.

Camera Installation

1. Find the best installation position to install backup camera on your vehicle.
2. Remove the camera U-shaped bracket, mark the hole position with a marker pen, then drilling, after the hole is finished, route the terminal wire of the camera through it and install the screw of the backup camera.
3. Be sure to use the vibration gasket when installing the camera.

Mount the Monitor

1. Find the best installation position to install monitor in your vehicle.
   Remove the screw around then take out the monitor,Put U type bracket to the right place and adjust angle, prepare 3 screws.(see below pictures)

2. Locking the bracket by screws.Put the monitor into the bracket, adjust angle and lock it.(see below pictures)

3. Finish installation. The adjustable angel is forward 30 and backward 30°. User can adjust a suitable angle by themself.(see below pictures)

Installation Optional

Monitor lnstallatton(Fan-shaped Mount)

1. 1. Secondly put the metal buckle piece on the top of the fan-shaped bracket into the notch at the back of the monitor.(see below pictures)

2. Move the bracket to the proper location.(see below pictures)
3. To fix the big screw of the bracket until to keep the monitor tight.(see below pictures)
4. If users want to change the direction or angle of the monitor, firstly to loosen the screws on the bottom of the bracket. Then move the monitor to the desired location then fix the screws on the bottom of the bracket again.(see below pictures)
   Monitor lnstallatton(Suction Cup Mount)

The suction cup mount is similar to the fan shaped mount, you can use it to mount the monitor on the windshield, it is not included in the package, if you need it, please contact us.

Operation

Operate the Monitor

1. Down select
2. Menu
3. Up select
4. Power
5. CHl and “·”
6. CH2 and “+”
7. MODE
8. Bracket knobs

activate the camera:
The backup camera takes power from the power cable of the monitor, just connect the 4-pin connector on the camera to the extension cable that connects to the monitor power cable, can activate the backup camera

Menu Oprate

MENU button operates the menu.

The following are examples of how the menus work:

1. Menu Press 1 time
   Image BRIGHTNESS CONTRAST SATURATION and RESET.

2. Menu Press 2 times
   Channel Setting: Parking guideling ON/OFF and delay setting.

3. Menu Press 3 times
   System Setting: Language setting, automatic brightness adjustment, channel up, down, left, right flips setting

4. Menu Press 4 times
   The volume setting

The down and up arrow buttons controsl up and down selection. The power ON/Off button control the screen to turn ON/OFF.
Select the channel that can be displayed on the monitor, or adjust the decrease or increase in the MENU state.
Select mode.

Specifications

Camera

System| NTSC
Operational Current (when transmitting)| <lSSmA
Pixels| 1920*1080P
Viewing Angle| Horizontal angle 100 degrees

Diagonal angle 120 degrees

Image Sensor| CMOS C2398 1/3
Minimal Illumination| 0.llux
Connector| 4 Pin Connector
Water-proof Standard| IP69K
Night Vision| Infrared Night Vision
Operation Temperature| -4° to 158°F(-20° to 70 “C)
Storage Temperature| -22· to 176°F(-30° to 80 ·c)

Care and Maintenance

Please do not use solvents or chemicals to clean or wipe the camera. If necessary, use a soft cloth dipped in neutral detergent to clean the dirt or stains.
Disposal
The system is designed to provide years of service and should be recycled or safety disposed of at a local recycling center.

Troubleshooting

Warranty

COMPONENT SOLUTION SERVICES (CSS) LIMITED ONE (1) YEAR WARRANTY

1. Veclesus® products’ warranties are not transferable. The warranties apply to the retail consumer for one (1) year and covers against defects in material and quality. Cables are not warrantied.

2. All warranty claimants must have consulted our technical support department for troubleshooting. Contact can be made via email at service@veclesusclub.com.

3. When the warranty claim is made, the consumer must establish the warranty start dates by presenting documentation regarding the date of retail purchase (e.g., bill of sale, order number).

4. Service performed by non-authorized service personnel may void ail warranty claims.The limited warranty does not cover damage resulting fom misuse, accident, modification, or alteration to hardware or software, tampering, unsuitable physical or operating environment beyond product specifications, improper maintenance, or failure caused by a product for which Veclesus is not
   responsible. There is no warranty for any product with removed or altered identification labels.

5. This warranty gives you specific legal rights, and you may also have other rights that vary from state to state.

6. veclesus does not provide any other warranties of any kind, including, but not limited to. the implied warranties or conditions of merchantability and fitness for a particular purpose. some jurisdictions do not allow the limitation of implied warranties. so this limitation may not apply to you.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>