HICFM FAN-R24T 24 Roll About Tilt Stand Fan Owner’s Manual

: June 15, 2024
: HICFM

Table of Contents

SAFETY INFORMATION
ASSEMBLY INSTRUCTION
OPERATION INSTRUCTION
CARE AND MAINTENANCE
1-YEAR LIMITED WARRANTY
REPLACEMENT PARTS LIST
Read User Manual Online (PDF format)
Download This Manual (PDF format)

24″ ROLL-ABOUT TILT STAND FAN
OWNER’S MANUAL

120V / 60Hz, 2.7A
ITEM NO.: FAN-R24T
READ & SAVE THESE INSTRUCTIONS
Questions, problems, missing parts? Before returning the product,
please e-mail our customer service by
hicfm@outlook.com

SAFETY INFORMATION

WARNING

Read and save these instructions. Do not operate fan unless you have read these instructions.
Unplug the fan before moving it or performing maintenance. Do not touch the fan when your hands are wet.
Those who are not qualified electricians should not disassemble, repair or rebuild the fan.
Unplug the fan when it is not in use.
DO NOT unplug the fan by pulling the cable cord. Unplug by holding the plug and pulling.
DO NOT use the fan when there is damage to the cable cord or plug. If the supply cord is damaged, it has to be replaced by the manufacturer, its service agent or similarly qualified persons.
To Reduce The Risk Of Fire, Electric Shock Or Injury To Persons, Do Not Use Replacement Parts That Have Not Been Recommended By The Manufacturer (e.g. Parts Made At Home Using A 3D Printer).
DO NOT use the fan close to fires.
DO NOT insert your hand or other objects into the grille or the movable parts.
To reduce the risk of fire or electric shock, do not use this fan with any solid-state speed control device.
DO NOT use this fan outdoors, this fan is designed for indoor use only.
To Reduce The Risk Of Fire Or Electric Shock Do Not Use With An Extension Cord.

CAUTION

Unplug the fan from the socket and clean it with a soft cloth.
DO NOT immerse the fan.
Fit the guard onto fan before starting up the fan.
This fan is not intended for use by people (including children) with reduced physical, sensory or mental capabilities or lack of experience and knowledge unless they have been given supervision or instruction concerning use of the fan by a person responsible for their safety. Supervise children to ensure they do not play with the fan.

ASSEMBLY INSTRUCTION

Remove the parts from the box.
Place the fan head (motor and guard assembly) on a flat level surface with motor on the top side.
Assemble two angled legs to one upright handle with bolt, flat washer, spring washer and nut through lower hole as shown in Figure 1. Make sure the handle and the leg with a hole through the side are facing the same direction. This will ensure that the wheels and handle will be to the rear of the assembly. Repeat these steps for the other leg assembly
Secure assemblies together with one cross-member as shown in Figure 2. Place cross-member on front side of assemblies and secure each with a bolt, flat washer, spring washer and nut through the top hole in the assemblies. Make certain that both handles are facing away from the cross-member.
As shown in Figure 3, align a cross-pole at the base of one leg angle. Align a cross- member to the front leg assembly with a bolt and through the cross-member, the leg assembly, and the cross-pole. Secure with flat washer, spring washer and nut. Repeat at rear and on both sides of the opposite leg.
Place rubber flanges between fan head and mounting frame. Secure fan head to assemble with tilting knobs. (See figure 4)
Attach wheels to frame with bolts, shaft, flat washer and nut. Then tighten them, and complete the fan assembly. (See figure 5)

OPERATION INSTRUCTION

Place the fan on a safe,,flat surface where it can not fall or be pulled by the cord.
Plug unit into electrical outlet.
Adjust the desired speed by rotating the switch knob at the back of fan.
Always turn off and unplug fan after using.
To adjust the angle of the airflow, loosen two fan head knobs, tilt the fan head to your desired angle, and re-tighten the fan head knobs.

CARE AND MAINTENANCE

Unplug the appliance before cleaning.Don’t use any water for cleaning metal surfaces,Slightly moisten a cloth and then wipe off the surfaces of the fan.In order to remove the dust from the grill, use a vacuum cleaner or remove the front grill by removing the securing screws on the edge of the grill. After cleaning, remount the grill. After doing this, fasten the screws on the edge of the grill.

1-YEAR LIMITED WARRANTY

The manufacturer warrants this product to be free from manufacturing defects in the material and workmanship under normal use for a period of one year after the date of purchase by the original purchaser.
This warranty does not cover transit damages. This warranty does not apply to damages from accident, misuse, alteration of any kind to the fan or where the connected voltage is more than above the nameplate voltage. This warranty does not apply to the finish on any portion of the product. Servicing performed by unauthorized persons shall render the warranty invalid. The warranty is not responsible for damages of any kind, including accident and consequential damages. Some states do not allow the exclusion or limitation of the incidental or consequential damages, so the above exclusion or limitation may not apply to you. This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.