VECLESUS EV-5588MS V5M Rear View Camera System User Manual

: June 15, 2024
: VECLESUS

Table of Contents

Components
Safety Informations
Getting Started
Installation Guide
Operation
Specifications
Care and Maintenance
Troubleshooting
Warranty
Read User Manual Online (PDF format)
Download This Manual (PDF format)

USER MANUAL
5” Car Wired
Backup Camera System

Welcome
Thanks for your purchase! This 5” one-to-one wired backup camera system is major designed to make you vehicle to get in and out of the parking space easily and safely.
In addition, this system is equipped with three trigger lines, you also can use aS a driver assistance system with two or three cameras, wires and only need to purchase additional extension cables and cameras.
Please read this manual carefully before installing and using.
If you encounter any problems please contact customer service: service@veclesusclub.com.
We reserve the rights to modify printing errors or update specifications without a prior notice.
We hope to have your understanding.

Components

Safety Informations

Usage

This wired backup camera system is designed to help the driver safely detect people and/or objects, help to avoid damage or injury. However, you the driver, must use it properly. Use of this system is not a substitute for safe, proper or legal driving.
Never back up/driving while looking at the monitor alone. You should always check behind and around the vehicle when backing up/driving, in the same way as you would if the vehicle dose not have the rearview camera system.
Please, always remember, the area displayed by the rear view camera system is limited. It does not display the entire panorama that is behind you.
The monitor is not designed to be waterproof. Exposure to water, such as rain, may damage the unit.

Installation

Electric shock or product malfunction may occur if this product is installed incorrectly.
Please use this product within the voltage range(9-36V) specified. Failure to do so can cause electronic shock or product malfunction.
Take special care when cleaning the monitor.
Make sure to firmly affix the product before use.
If smoke or a burning smell is detected, disconnect the system immediately.
Where the power cable may touch a metal case, cover the cable with a friction tape. A short circuit or disconnected wire may cause a fire.
While installing the Rear View System be careful with the wire positioning in order to avoid wire damage.
Do not install the monitor where it may obstruct drivers view or obstruct an air bag device.

Getting Started

3.1 Test the system
To ensure that the system works properly after installation, all components should be tested and checked before installation.

Refer to the component page to check whether the component is missing. We do not rule out that some components may be damaged in the case of violent loading and unloading during transportation.
If so, please contact us intime.
Connect the power cable(13 pin connector) to the monitor, the positive and negative terminals to 9-36v voltage, then the power button willturn red, press the power button, all the buttons into blue backlight, indicating the successful test of the display, can work normally.
Connect 4-pin connector(the other end of the power cable)to the backup camera, restart the power supply of the monitor, and the corresponding channel image will appear ( Note: The monitor can only display the image of the camera of the corresponding channel, if your camera is connected to the CH1 channel, please switch the monitor to CH1), If display normally, so the backup camera is working properly. If not, please refer to the Troubleshooting.

3.2 Before Beginning Installation

As the camera need to be fixed on the vehicle, it may need to drill a hole on your car, before drilling please measure the size of boreholes and check that no cable or wiring is on the other side of the wall.
Please clamp all wires securely to reduce the possibility of them being damaged while vehicle is in use.
Keep all cables away from hot or moving parts and electrical noisy components.

ATTENTION

Attach camera to bracket using screws provided and adjust the angle.
Be sure to position the cable properly. The camera cable uses waterproof connectors which means the camera cable can be exposed to all weather conditions.
Donotrun the cable over sharp edges, do not kink the cable and keep away from HOT and rotating parts.
Feed as much cable as possible into vehicle & clamp securely. This reduces the possibility of cable being hooked or snagged.
Attach monitor to mount, and adjust mounting angle to allow optimum driver viewing comfort.
The camera system can be wired to be powered “ON” the entire time the vehicle is on. This is typical in RV andsome commercial applications.

Installation Guide

4.1 System Connection Diagram

4.2 Recommended Installation Location

4.3 Cable Connections

RED wire to ignition hot (+) 9-36 volts.
BLACK wire to ground (-)
(please use a chassis ground post).
BROWN trigger wire is for camera 1.
Connects brown trigger wire to backup light wire or backup beeper wire. This connection need to activate the monitor when putting the vehicle into reverse.
BLUE (CAM 2) trigger wire for accessory cameras (side cameras etc.) DO NOT power this wire unless you intend to trigger a second camera. It will be connected to your trigger power source, suchas a turn signal light wire.
GRAY (CAM3) trigger wire for accessory cameras (side cameras etc.) DO NOT power this wire unless you intend to trigger a third camera.

4.4 Powered By Fuse Box

Normally, we connect the RED Wire(ACC+) to the fuse switch.
Find the car circuit fuse box under your car cab.
Then according to the labels on the fuse hardwire kit to find the corresponding power fuse and connect the corresponding trigger line (voltage must between 9-36V).

4.5 Camera Installation

Find the best installation position to install backup camera on your vehicle.
Remove the camera U-shaped bracket, mark the hole position with a marker pen, then drilling, after the hole is finished, route the terminal wire of the camera through it and install the screw of the backup camera.
Be sure to use the vibration gasket when installing the camera. It is package with the camera hex wrench.

4.6 Mount the Monitor

Find the best installation position to install monitor in your vehicle.
Remove the screw around then take out the monitor. Put U type bracket to the right place and adjust angle, prepare 3 screws. (see below pictures)
Locking the bracket by screws. Put the monitor into bracket, adjust angle and locking it. (see below pictures)
Finish installation. The adjustable angel is forward 30° and backward 30°. User can adjust a suitable angle by themself. (see below pictures)

4.7 Installation Optional

Firstly please fix the screws and let fan shaped bracket tight.(see below pictures)
Secondly put the metal buckle piece on the top of the fan-shaped bracket into the notch at the back of the monitor.(see below pictures)
Move the bracket to the proper location. (see below pictures)
To fix the big screws of the bracket until to keep the monitor tight. (see below pictures)
If users want to change the direction or angle of the monitor, firstly loosen the screws on the bottom of the bracket. Secondly move the monitor to the desired location Lastly fix the screws on the bottom of the bracket again.(see below pictures)

Operation

5.1 Remote Control

1. Power
2. CH1/CH2/CH3 change
3. Positive increase| 4. Menu
5. Negative decrease
6. Mode selection
---|---

5.2 Menu Operate

Buttons from Left to Right

The menu button operates the menu:

The following are examples of how the mens work. The down and up arrow buttons control decreases and increases. Menu Press 1 time
PICTURE: Brightness, displays on the screen.
BRIGHTNESS
llllllllllllllllllll………………….. 20

Menu Press 2 times
CONTRAST: Contrast, displays on the screen.
CONTRAST
llllllllllllllllllll………………….. 20

Menu Press 4 times
VOLUME: displays on the screen.
VOLUME
llllllllllllllllllll………………….. 20

Menu Press 5 times
ZOOM Toggles between 16:9 and 4:3 image ratio
Menu Press 6 times
“ICON” Image Orientation:
This selection flips each camera image individually both horizontally and vertically. This allows fora correct image of interior/forward-facing cameras.

Menu Press 7 times
ACC time monitor stays on after the trigger wire is deactivated. It can be set to0O, 2,5, and 10-second delays.
SIDE CAMERA HOOK UP – when adding a side camera, set that camera delay to 2 seconds.

Menu Press 8 times
LANG(LANGUAGE): “Show English as primary language”, displays on the screen.
LANG ENGLISH
Menu Press 9 times
RESET: Resets the monitor to factory setting.

5.3 Parking Guide Line/Mirror Image
Control the parking guide line:
Open or close the parking guide line by retaining or picking off the short circuit cap on the green wire, which near the 4-Pin connector on the camera cable tail, default setting is with parking guide line, pick off the cap on green wire, parking guide line is cancelled.

Mirror lmage:
Default setting is mirror image, pick off the short circuit cap on the white wire, shows pre-image.

Specifications

Camera

Monitor

Care and Maintenance

Please do not use solvents or chemicals to clean or wipe the camera. If necessary, use a soft cloth dipped in neutral detergent to clean the dirt or stains.
Disposal
The system is designed to provide years of service and should be recycled or safety disposed of at a local recycling center.

Troubleshooting

Error/malfunction	Possible Causes	Solutions/repair
The monitor does not display images	The monitor is not in standby status

Please make sure that the monitor is powered, and the power button on the monitor is turn on
The camera was not connected successfully| Check if the camera is with correct connection
Bad contact with power cable| Make sure that the red wire or black wire on the power cable is connected correctly
The channel of the camera does not match the channel display on the monitor| Adjust the display channel of the monitor to correspond to the camera. If the camera is connected to CH1 wire, please adjust the monitor display to CH1
The voltage is not in the normal operating range| To enable the system to run normally, connect the system to a voltage range from DC 9 to 36V
The trigger line of the corresponding channel is not connected| Each video input channel has its trigger line. Please check and make sure if the trigger line is properly connected
The monitor dose not display images| The black wire(GND) is not connected properly| Please check and make sure if the GND wire (black wire) is properly connected, please use a chassis ground post.
---|---|---
The red power wire is not connected properly| Please check and make sure if the hot wire (red power wire) is properly connected
The image shakes when the vehicle
is moving| The screws that fixed the camera angle are loose| Check the screws which fix the camera angle, tighten these screws if necessary
The screws connecting the camera and the vehicle are loose| Check the screws that attach the camera to vehicle, tighten these screws if necessary
Other troubles| Please contact support team via: service@veclesusclub.com
Installation videos|
After-sale group|

Warranty

COMPONENT SOLUTION SERVICES (CSS)
LIMITED ONE (1) YEAR WARRANTY

Veclesus® products’ warranties are not transferable. The warranties apply to the retail consumer for one (1) year and covers against defects in material and quality. Cables are not warrantied.
All warranty claimants must have consulted our technical support department for Troubleshooting.
Please contact support via email service@veclesusclub.com.
When the warranty claim is made, the consumer must establish the warranty start dates by presenting documentation regarding the date of retail purchase (e.g., bill of sale, order number).
Service performed by non-authorized service personnel which may void ail warranty claims. The limited warranty does not cover damage resulting fom misuse, accident, modification, or alterat ion to hardware or software, tampering, unsuitable physical or operating environment beyond product specifications, improper maintenance, or failure caused by a product for which Veclesus is not responsible. There is no warranty for any product with removed or altered identification labels.
This warranty gives you specific legal rights, and you may also have other rights that vary from state to state.
Veclesus DOES NOT PROVIDE ANY OTHER WARRANTIES OF ANY KIND, INCLUDING, BUT NOT LIMITED TO. THE IMPLIED WARRANTIES OR CONDITIONS OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. SOME JURISDICTIONS DO NOT ALLOW THE LIMITATION OF IMPLIED WARRANTIES. SO THIS LIMITATION MAY NOT APPLY TO YOU.