VECLESUS VMQD 7 Inch 1080P HD DVR Wired Backup Camera System User Manual

VECLESUS VMQD 7 Inch 1080P HD DVR Wired Backup Camera System

Components

VECLESUS VMQD 7 Inch 1080P HD DVR Wired Backup Camera System fig 1

Safety Information

Usage

• This system is designed to help the driver safely detect people and/or objects to avoid damage or injury. However, you must use it properly. Use of this system is not a substitute for safe, proper or legal driving.
• Never back up/driving while looking at the monitor alone. You should always check behind and around the vehicle when backing up/driving, in the same way as you would if the vehicle did not have the rearview camera system.
• Please, always remember, the area displayed by the rear view camera system is limited. It does not display the entire panorama that is behind you.
• The monitor is not designed to be waterproof. Exposure to water, such as rain, may damage it.

Installation

• Electric shock or product malfunction may occur if this product is installed incorrectly.
• Please use this product within the voltage range(9-36V) specified. Failure to do so can cause electronic shock or product malfunction.
• Take special care when cleaning the monitor.
• Make sure to firmly affix the product before use.
• If smoke or a burning smell is detected, disconnect the system immediately.
• Where the power cable may touch a metal case, cover the cable with a friction tape. A short circuit or disconnected wire may cause a fire.
• While installing the Rear View System should be careful with the wire positioning in order to avoid wire damage.
• Do not install the monitor where it may obstruct drivers view or obstruct an air bag device.

Getting Started

Test the system
To ensure the system works properly after installation, all components should be tested and checked before installation.

1. Refer to the component page to check whether the component is missing. We do not rule out that some components may be damaged in the case of violent loading and unloading during transportation. If so, please contact us in time.
2. Connect the power cable to the monitor, the positive and negative terminals to 9-36v voltage, then the power button will turn red, press the power button, all the buttons into blue backlight, indicating the successful test of the display, can work normally.
3. Connect 4-pin connector(the other end of the power cable)to the backup camera, restart the power supply of the monitor, and the corresponding channel image will appear (Note: The monitor can only display the image of the camera of the corresponding channel, if your camera is connected to the CH1 channel, please switch the monitor to CH1), If it displays normally, so the backup camera is working properly. If not, please refer to the Troubleshooting.

Before Beginning installation

• As the camera need to be fixed on the vehicle, it may need to drill a hole on your vehicle, before drilling please measure the size of boreholes and check that no cable or wiring is on the other side of the wall.
• Please clamp all wires securely to reduce the possibility of them being damaged while vehicle is in use.
• Keep all cables away from hot or moving parts and electrical noisy components.

ATTENTION

• Attach camera to bracket using provided screws and adjust the angle.
• Be sure to position the cable properly. The camera cable uses waterproof connectors which means the camera cable can be exposed to all weather conditions.
• Do not run the cable over sharp edges, do not kink the cable and keep away from HOT and rotating parts.
• Feed as much cable as possible into vehicle & clamp securely. This reduces the possibility of cable being hooked or snagged.
• Attach monitor to mount, and adjust mounting angle to allow optimum driver viewing comfort.
• The camera system can be wired to be powered “ON” the entire time when the vehicle is on. This is typical in RV and some com- mercial applications.

Installation Guide

System Connection Diagram

Recommended Installation Location

Cable Connections

1. CH1\CH2\CH3\CH4 4PIN connector: 4CH video input inputs interface.
2. BAT yellow line: 12V-36V power supply(Connect to the positive pole).
3. ACC red wire: 12V-36V power supply{Connect to the key ignition circuit).
4. GND black wire: negative pole( connect to the negative pole).
5. Forward wire(CHl) brown wire: trigger CH 1 single image to full screen.
6. Reversing wire(CH2) green wire: trigger CH2 single image to full screen.
7. Turning lamp wire {CH3) blue wire: trigger CH3 single image to full screen.
8. Turning lamp wire(CH4) gray wire: trigger CH4 single image to full screen.

Tips: BAT yellow wire and ACC red wire cannot be screwed together to con nect to the ACC line to take power. After power off and power on again, the recording time will not be saved. Other functions are normal. Please take power according to the usage requirements

Button Reference(Monitor)

1. MENU: on split interface, press shortly to turn on/off OSD menu (same as “OK” key on the remote controller), press and hold for Ss to lock the key on the front panel, press and hold for Ss again to recover the function.
2. CHl: enter into CHl or move to the left side (same as left arrow on the remote controller).
3. CH2: enter into CH2 or move to the right side (same as right arrow on the remote controller).
4. Power: press and hold to power on and power off the monitor, and press shortly to open and close the display screen (same as POWER key on the remote controller).
5. CH3: enter into CH3 or mover down or -1 when setup the parameter (same as down arrow on the remote controller).
6. CH4: enter into CH4 or move up or +l when setup the parameter (same as up arrow on the remote controller).
7. MODE: on split interface, press shortly to change to different multiple images display circularly (same as MODE key on the remote controller), on menu interface, press shortly to confirm (same as OK key on the remote controller).

The power cord is recommended to be connected directly to the positive and negative terminals of the vehicle battery, or after the battery is connected to the fuse box, connect the positive and negative poles of the power supply. It is forbidden to connect to the metal conductor in the car as the ground wire, otherwise, a negative pulse will be generated to interfere with the normal operation of the monitor.

4PIN connector definition (Support 1CH audio input, optional function)

Button Reference(Remote)

1. Startup/shut off monitor
2. Return to the default screen/to the previous step 3
3. Switch multi-screen display mode circularly 1
4. CHl single image full screen display
5. CH2 single image full screen display
6. CH3 single image full screen display
7. CH4 single image full screen display
8. Up
9. Down
10. Left
11. Right
12. Menu + confirmation

Mount the Monitor

1. Find the best installation position to install monitor in your vehicle. ****
   Remove the screw around then take out the monitor,Put U type bracket to the right place and adjust angle, prepare 3 screws.(see below pictures)

2. 3. Locking the bracket by screws.Put the monitor into the bracket, adjust angle and lock it.(see below pictures)
3. 5. 3. Finish installation. The adjustable angel is forward 30 and backward 30°. User can adjust a suitable angle by themself.(see below pictures)

Installation Optional
Monitor installation(Fan-shaped Mount)

1. Secondly put the metal buckle piece on the top of the fan-shaped bracket into the notch at the back of the monitor.(see below pictures)
2. Move the bracket to the proper location.(see below pictures)
3. To fix the big screw of the bracket until to keep the monitor tight.(see below pictures)
4. If users want to change the direction or angle of the monitor, firstly to loosen the screws on the bottom of the bracket. Then move the monitor to the desired location then fix the screws on the bottom of the bracket again.(see below pictures)
   Monitor lnstallatton(Suction Cup Mount)
   The suction cup mount is similar to the fan shaped mount, you can use it to mount the monitor on the windshield, it is not included in the package, if you need it, please contact us.

 Operation

Operate the Menu
Press “OK” key on the remote controller or press the “MENU” button on the screen to enter into the menu interface; use the arrow keys on the remote controller or the “Left” and “Right” buttons on the panel to move the check box, then press the “MENU” key on the remote controller or short press the “MENU” button to confirm the selection and enter into the next sub-menu.
Playback

Press the remote controller arrow key or panel key to move the selection box, then press the remote controller “OK” key or press the “MENU” key shortly to confirm.

1. Search according date: display the stored video files:
   CD last three days aJ last week ® last two weeks @ last month ® all

2. Playback: display the recording files on the monitor(support fast forward, fast reverse, pause, etc).

3. Prev: switch to display the previous page of video files.

4. Next page: switch to display the next page of video files.

5. Lock: lock the selected video file and protect it from being automatically deleted and overwritten by the equipment.

6. Unlock: unlock the locked video files.

7. Backup: copy and store the selected video files to an external U disk, which can be plugged into a computer to play directly.

Press arrow keys of the remote controller or the panel keys to move the selection box, then press “OK” key of the remote controller or press “MENU” key shortly to confirm the option and enter the current setting. After completing the setting, press the “OK” key or the “MENU” key to exit the setting state, and select “OK” to save and exit.

1. System time: modify the system time and date.
2. Date format: change the display format of year, month and day.
3. Output format: PAL system or NTSC system.
4. Language: Chinese and English menus(support customized other languages).
5. Time show: turn on and off the time display.
6. VGA resolution-output resolution adjustment(800600/1024768/ 1280720/19201080).
7. Video quality: normal/standard/high definition/ultra high definition.
   Plate number: add license plate number or driver’s name on the recording video.

Video resolution| l0Mins Storage| SG| 32G| 64G| 128G| 256G
---|---|---|---|---|---|---
Normal| 110M| 12 hours| 48 hours| 96 hours| 192 hours| 384 hours
Standard| 220M| 6 hours| 24 hours| 48 hours| 96 hours| 192 hours
HD| 330M| 4 hours| 16 hours| 32 hours| 64 hours| 128 hours
Super HD| 440M| 3 hours| 12 hours| 24 hours| 48 hours| 96 hours

Control Setting Video output:

1. always output: the display screen always outputs the display picture after starting up.
2. Trigger output: the display screen does not display pictures all the time after starting up, and display images after turning or triggered.
3. intelligent output: the display screen displays the picture after startup, and automatically closes the picture after 15 seconds if no operation.
4. Video exit -how long the camera screen displays after exiting trigger (on the screen closed status).
5. Turn light-turn on or off the displayed image after turning(on the screen closed state).
6. Emergency light -turn on or off the displayed image after emergency light on(double click the emergency light to turn on).
7. Turn light display-select the display mode triggered by turn light (left and right two images or full screen single image).
8. Frame color-color selection of border of Split Line between images, none-close border.
9. Record for park-24-hour delay recording function(please do not turn on all the time to avoid battery loss).
10. Channel title: turns on and off the channel characters displayed on the screen.

Video

1. Assist line(the current setting will be automatically saved after pressing return key to exit).
   Adjust the position and length of assist line for each channel independently. Color: None(i.e. close assist line); Select “Move A-a”, press the panel key or the arrow on the remote controller to move and adjust the distance and position of assist line(same for “Move B-b”, “Move C-cH and “Move D-d”).

2. Screen margin(the current setting will be automatically saved after pressing return key to exit).
   Press the panel key or remote control arrow to adjust the margins around the output video are compressed inwards, which is suitable for full screen display on various display screens.

3. Color(the current setting will be automatically saved after pressing return key to exit.
   Press the panel key or remote controller arrow to adjust the chroma, brightness, sharpness, contrast and saturation of each channel independently.

4. Mirror(the current setting will be automatically saved after pressing Press the panel key or remote controller arrow to adjust the image of each channel. Mirror, Flip, 90 degree rotation, 270 degree rotation optional.

5. Image adjust(the current setting will be automatically saved after pressing return key to exit). Cut each channel picture independently and adjust the display range of each channel image.

System maintenance

1. Format(the memory card has to be format at first use).
2. Upgrade-upgrade the product.
3. Confirm-restore the product to the factory default settings.
4. Param configuration.
   Export: export the current setting parameter configuration to the monitor operating memory or memory card to store.
   Import: import the setting parameter configuration stored in the monitor operating memory or the memory card(import the parameter configuration of the memory card preferentially).

Product Specification

1. lnput signals: CVBS/960H/AHD720P/AHD1080P
2. Output system: PAL/NTSC optional
3. Storage: maximum support 256GB SD card
4. Resolution: 1920*1080
5. Working voltage: 12V -36V(minimum input 13V for camera)
6. Operating current: 12V/450mA(excluding display screen and camera)
7. Output signals: 40pin-LVDS or pin-TTL
8. Bootup time: 11 seconds
9. Recording format: H.264
10. Software update: by memory card
11. Trigger voltage: 12V-24V
12. Operating temperature: -2o·c~+ 70°C

Specifications

Camera

System| NTSC
Operational Current (when transmitting)| <155mA
Pixels| 1920*1080P
Viewing Angle| Horizontal angle 100 degrees Diagonal angle 120 degrees
Image Sensor| CMOS C2398 1/3
Minimal Illumination| 0.llux
Connector| 4 Pin Connector
Water-proof Standard| IP69K
Night Vision| Infrared Night Vision
Operation Temperature| -4° to 158°F( -20° to 70 °C )
Storage Temperature| -22° to 176°F( -30° to 80°C)

Monitor

LCD Diplay Screen Size| 7 Inch
System| PAL&NTSC automatically
Effective Pixels| 1024RGB600 BOE
Operating Voltage| DC 9-36V
Video Input s| 4
Trigger s| 4
Aspect ratio| 16:9
Standby Current| 80mA
Operational Current| <300mA
Operation Temperature| -4° to 158°F (-20° to 7o· c )
Storage Temperature| -22° to 176°F (-30 ° to so· c )

Care and Maintenance

Please do not use solvents or chemicals to clean or wipe the camera. If necessary, use a soft cloth dipped in neutral detergent to clean the dirt or stains.
Disposal
The system is designed to provide years of service and should be recycled or safety disposed of at a local recycling center.

Troubleshooting

The monitor dose not display images

| ****

The monitor is not in standby status

| Please make sure that the monitor is powered.and the power button on the monitor is turn on
The camera was not connected successfully| Check if the camera is on correct connection
Bad contact with power cable| Make sure that the red wire or black wire on the power cable is connected correctly.

The channel of the camera does not match the channel display on the monitor

| ****

Adjust the display channel of the monitor to correspond to the camera. If the camera is connected to CHl wire, please adjust the monitor display to CHl

The voltage is not in the normal operating range| To enable the system to run normally, connect the system to a voltage range of DC 9 to 36V
The trigger line of the corresponding channel is not connected| Each video input channel has its trigger wire. Please check and make sure if the trigger wire is properly connected.

The monitor dose not display images

|

The black wire(GND) is not connected properly

| Please check and make sure if the GND wire (black wire) is properly connected, please use a chassis ground post or nagative pole.
The red power wire is not connected properly| Please check and make sure if the hot(+) wire (red power wire) is properly connected.

The Image shakes when the vehicle is moving

| The screws that fixed the camera angle are loose| Check the screws which fix the camera angle, tighten these screws if necessary.
The screws connecting the camera and the vehicle are loose|

Check the screws that attach the camera to vehicle, tighten these screws if necessary

Other trouble| Please connect support team via: service@veclesusclub.com
Installation Videos|

After -sal e Group

|

Veclesus rear view safety club

Warranty

COMPONENT SOLUTION SERVICES (CSS) LIMITED ONE (1) YEAR WARRANTY

1. Veclesus® products’ warranties are not transferable. The warranties apply to the retail consumer for one (1) year and covers against defects in material and quality. Cables are not warrantied.
2. All warranty claimants must have consulted our technical support department for troubleshooting. Contact can be made via email at service@veclesusclub.com.
3. When the warranty claim is made, the consumer must establish the warranty start dates by presenting documentation regarding the date of retail purchase (e.g., bill of sale, order number).
4. Service performed by non-authorized service personnel may void ail warranty claims.The limited warranty does not cover damage resulting fom misuse, accident, modification, or alteration to hardware or software, tampering, unsuitable physical or operating environment beyond product specifications, improper maintenance, or failure caused by a product for which Veclesus is not responsible. There is no warranty for any product with removed or altered identification labels.
5. This warranty gives you specific legal rights, and you may also have other rights that vary from state to state.
6. Veclesus does not provide any other warranties of any kind, including, but not limited to. the implied warranties or conditions of merchantability and fitness for a particular purpose. some jurisdictions do not allow the limitation of implied warranties. so this limitation may not apply to you.

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>