VECLESUS WM1 1080P HD Wireless Backup Camera System User Manual

June 16, 2024
VECLESUS

VECLESUS WM1 1080P HD Wireless Backup Camera System

Welcome

  • Thank you for your purchase!
  • Please read this manual carefully before installation and use.
  • If you encounter any problems
  • Please contact customer support: service@veclesusclub.com.
  • We reserve the right to modify printing errors or update specifications without notice. Hope you can understand.

WHAT’S IN THE CARTON

Contents
Confirm that the following parts are included

VECLESUS-WM1-1080P-HD-Wireless-Backup-Camera-System-
FIG-1

Note: If any part of your product is damaged, do not use it.
Contact your authorized VECLESUS customer service.

IMPORTANT SAFETY INSTRUCTIONS

Please read and keep all safety and use instructions.

Usage

  • This system is designed to help the driver safely detect people and/or objects helping to avoid damage or injury. However, you must use it properly. Use of this system is not a substitute for safe, proper or legal driving.
  • Never back up/drive while looking at the monitor alone. You should always check behind and around the vehicle when backing up/driving, in the same way as you would if the vehicle did not have the rearview camera system.
  • Please, always remember, the area displayed by the rear view camera system is limited. It does not display the entire panorama that is behind you.
  • The monitor is not designed to be waterproof. Exposure to water, such as rain, may damage the unit.

Installation

  • Please install this product within the voltage range (9-36V) specified. Failure to do so can cause electronic shock or product malfunction.
  • An electric shock or product malfunction may occur if this product is installed incorrectly.
  • If smoke or a burning smell is detected, disconnect the system immediately.
  • Make sure to firmly affix the product before use.
  • Take special care when cleaning the monitor.
  • Where the power cable may touch a metal case, cover the cable with friction tape. A short circuit or disconnected wire may cause a fire.
  • While installing the rear view system should be careful with the wire positioning to avoid wire damage.
  • Do not install the monitor where it may obstruct the driver’s view or obstruct an airbag device.
  • Feed as much cable as possible into the vehicle & clamp securely. This reduces the possibility of the cable being hooked or snagged.
  • Keep all cables away from hot or moving parts and electrical noisy components.

IMPORTANT SAFETY INSTRUCTIONS

  • Where the power cable may touch a metal case, cover the cable with friction tape. A short circuit or disconnected wire may cause a fire.
  • While installing the rear view system should be careful with the wire positioning to avoid wire damage.
  • Do not install the monitor where it may obstruct the driver’s view or obstruct an airbag device.
  • Feed as much cable as possible into the vehicle & clamp securely. This reduces the possibility of the cable being hooked or snagged.
  • Keep all cables away from hot or moving parts and electrical noisy components.

INSTALLATION GUIDE

Connection Diagram

VECLESUS-WM1-1080P-HD-Wireless-Backup-Camera-System-
FIG-2

  1. Monitor
  2. Camera
  3. Camera power cable
  4. USB power cable for monitor
  5. Cigarette lighter charger

Functions

  1. “+” key: press to increase value of Brightness, Contrast, Color, Hue.
  2. MENU: open menu or exit menu.
  3. “-” key: press to reduce the value of Brightness, Contrast, Color, and Hue.
  4. Power interface: DC 5V input.

VECLESUS-WM1-1080P-HD-Wireless-Backup-Camera-System-
FIG-4

NOTES:
There are two methods to connect this backup camera power cable:

  1. To show video continuously while driving: you can connect it to the license plate lamps, and then turn on the lamps so you can always get the video while driving.
  2. To show the video as a reversing system only, connect it to your reversing lights.

Monitor Connections

Monitor:

  1. Plug the small end of the USB cable into the micro-USB connector on the back of the monitor.
  2. Plug the other end into the car charger(provided).
  3. Plug the car charger into the car cigarette lighter hole.

Camera Connections

Camera:

  1. Use the mini 4-pin connector of the camera power cable to connect the tail wire on the backup camera.
  2. Connect the other end of the camera power cable (black and red wires) to the reversing light(reversing only) or license plate lamp(continuous running) power cable to connect the tail wire on the backup camera.VECLESUS-WM1-1080P-HD-Wireless-Backup-Camera-System-FIG-9

Install Monitor

  1. Connect the monitor wire through the wiring diagram.
  2. Select the best location to install the monitor attach it to the mount, and adjust the mounting angle to allow optimum driver viewing comfort. The package provides a dual-purpose adhesive bracket that can be mounted on the windshield or on the dashboard

Install Camera

  1. Connect the camera wire and reference the wiring diagram.

  2. Find the position of the car’s reversing light, then remove the interior baffle near the rear of the trunk and find the line position of the reversing light (Please use the electroscope to detect the positive and negative poles of the reversing line).

  3. Remove the license plate and put the extension cable of the camera through the hole (You may need to drill a hole if necessary) on the back of the license plate on the trunk, and connect the camera power cable to the camera extension cable, tape the connector together.
    Note: If connecting the power cord to the battery directly, the camera is always ON and may cause the battery to drain, Therefore we recommended to connect the power cord to the ignition switch. The parking guide line can be turned on/off by manually in Monti

  4. Connect the red wire of the power cable to the positive pole of the reverse lamp. the black wire is connected to the negative pole of the reverse lamp or the chassis ground on your trunk.

  5. Then mount the camera bracket behind the license plate, Increase the fastness with 3M tapes on the camera, and then reinstall the plate, If you worry that the camera is not secure enough, you can use the self-tapping screws provided to fix the camera on the car. Now, a camera installed successfully.

  6. Feed as much cable as possible into the vehicle & clamp securely. For any installation problems, please contact service@veclesusclub.com

Camera
If there is no wiring hole reserved above the car license plate, it may be necessary to drill a 7mm hole for through the wire. Before drilling, please make sure there are no other wires on the back of the car trunk to avoid short circuit.

If you worry about the camera is not secure enough, you can use the self- tapping screws (provided) to fix the camera on the car.

Cable
Be sure to position the cable properly. The camera cable uses aircraft-grade connectors which means the camera cable can be exposed to all weather elements. Do not run the cable over sharp edges, do not kink the cable and keep away from HOT and rotating parts.
Fasten all cables and secure all excess cables.

Monitor

  • Attach the monitor to the dashboard or windshield.
  • Attach the monitor to the mount, and adjust the mounting angle to allow optimum driver viewing comfort

Monitor Dimensions

VECLESUS-WM1-1080P-HD-Wireless-Backup-Camera-System-
FIG-18

Monitor Specifications

Display 4.3″ LCD digital panel
Screen ratio 16:9
Resolution 800*480
Contrast 800: 1
Viewing angle Hor. L(70) R(70) Ver. Up(S0) Down(70)
Primary Language English, Espanol, Simplified Chinese
Shockproof level 4G
Transmission distance About 100M(328ft) in open area
Power supply DC12-24V
Power consumption < 3W
Working temperature -4’F to 158’F
Size 4.6•3.l•0.75in
Weight 0.54KGS(l.2Lb)
AV input 1 channel input

Other features

| Startup automatically once powered on, with parking guide line, Mirror and non-mirror switchable

SPECIFICATIONS

Camera Dimensions

VECLESUS-WM1-1080P-HD-Wireless-Backup-Camera-System-
FIG-19

Camera Specifications

Pixel 1920*1080
Viewing angle Diagonal Angle 149°
Waterproof level IP68
Transmission distance 100M(328ft) in open area
Power supply DC12-24V
Working temperature -4°F to 158°F
Size 3.5 1.5 1.8in
Weight 0.35KGS

Function Operation Introduction

Menu setting
Press the “MENU” button on the panel to set the brightness, contrast, and saturation. Press the “+” or “-” panel to increase or decrease the specific value. After the setting is completed, wait for 5 seconds to automatically save and exit the menu. As shown in the picture below:

VECLESUS-WM1-1080P-HD-Wireless-Backup-Camera-System-
FIG-20

Mirror and non-mirror setting
Press “+” or ” on the panel to adjust the mirror and non-mirror switchable.

Parking guide line

Press the “M” key to enter the H1 option, and press the “+” or ” “button to add the scale left and right:

SYSTEM CONTROLS

Press the “M” key to enter the H2 option, press the “+” or ” ” button to adjust the scale enlargement/reduction;
Press the “M” key to enter the V option, and press the “+” or “” button to adjust the scale up and down.

Camera pairing

Long press the “M” button on the panel for 2 seconds, enter the pairing state (which lasts for 105), and display the pairing state (as shown in the figure below). in the pairing state, disconnect the power supply of the camera and re-power, then appears image screen, the pairing is successful, otherwise, it will display “Pair fail” which means pairing failure, you need to re-pair.

Trouble Shooting

Monitor no image

  1. Check the car charger connection, the blue indicated light is on or not.
  2. Check the USB cable connection, and try it again with another USB cable.
  3. Check whether there are any other things in the monitor interface, and clear the interface.

If there are no problems with the above points, maybe the monitor is damaged, please contact customer support
Email: service@veclesusclub.com.

Pairing failure

  • Check whether the camera power cable is connected correctly or not and whether the interface connection is OK.
  • If there is no problem with the power cable connection, then maybe the camera is damaged, please return it to the factory for repair. You can also get the pairing video by searching text “f6Clu22_J7w” on YouTube.com.

Bad signal/halted

  1. This product is suitable for cars or trucks within 10M(32.8ft).
  2. Please do not put the camera’s antenna box close to the iron part, which will affect the signal frequency.
  3. Under different environments, sometimes there will be a delay but not halted, which is no signal.

Installation support via: service@veclesusclub.com or scan the QR code below:

CONTACT

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals