levenhuk WA50 Weather Station User Manual

: June 5, 2024
: levenhuk

Table of Contents

Base station
Getting started
Time setting
Time zone setting
Alarm setting
Temperature units setting
Specifications
Care and maintenance
Battery safety instructions
Levenhuk Warranty
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

Discovery Report WA50
Weather Station
User Manual

levenhuk WA50 Weather Station

Base station

|
---|---
levenhuk WA50 Weather Station - Fig 1 |
---|---
1. Time display
2. Alarm
3. Indoor temperature
4. Indoor humidity
5. Calendar and weekday
6. Low battery indicator
7. Outdoor temperature
8. Outdoor humidity
9. Snooze| 10. SET button
11 ALARM button
12. ▲/ZONE button
13. ▼ button
14. CHANNEL button
15. Wall mount holes
16. Table stand (fold-out)
17. Battery compartment
18. RESET button

Sensor

LED indicator
Channel switch (1—3)
Wall mount hole
Battery compartment

The kit includes a base station, sensor, user manual, and warranty.
Also required (not included): 2 AAA batteries for the sensor; 4 AA batteries for the base station.

Getting started

Base station

Open the battery compartment cover (17) and insert 4 batteries according to Place the base station and the remote sensor within the effective transmission range.
If the reception is successful, the display will show the temperature and humidity of the outdoor sensor. If the values are not received from a channel, check the batteries and try when changing batteries, to replace the batteries first in the base unit, and then in the sensor, to re-establish the connection. If you change the batteries only in one of the devices (for example, in the sensor), the signal may not be received correctly.
The default channel is channel 1.To change it, press and hold the CHANNEL button on the base station, and then press the button again to choose between channels 1, 2, and 3.
The effective range may differ depending on the unit’s position. Due to interference (various remote control devices, etc.), the maximum distance between the base unit and the sensor may be significantly reduced. In such cases, we suggest moving the base unit and sensor a little. Sometimes it is enough to move one of these units a few inches!

Sensor

Open the battery compartment cover (4). Insert 2 batteries according to the correct polarity. Close the cover.

Sensor connection

Place the base station and the remote sensor within the effective transmission range.
If the reception is successful, the display will show the temperature and humidity of the outdoor sensor. If the values are not received from a channel, check the batteries and try them again. Check if there is any source of interference.
When changing batteries, replace the batteries first in the base unit, and then in the sensor, to re-establish the connection. If you change the batteries only in one of the devices (for example, in the sensor), the signal may not be received correctly.
The default channel is channel 1. To change it, press and hold the CHANNEL button on the base station, and then press the button again to choose between channels 1, 2, and 3.
The effective range may differ depending on the unit’s position. Due to interference (various remote control devices, etc.), the maximum distance between the base unit and the sensor may be significantly reduced. In such cases, we suggest moving the base unit and sensor a little. Sometimes it is enough to move one of these units a few inches!

NOTE! Although the sensor is weather-resistant, never place it in direct sunlight or in the rain or snow.

Time setting

Press the SET button and hold it for 3 seconds. The digits that are to be set are flashing. Press ▲/ZONE or ▼ to change the value, and then press SET to continue. The setting order: 12/24hr > Hour > Minute > Year > Month >
Date > DST ON/OFF. Finally, press the SET button to save the settings and exit.

Time zone setting

Press ▲/ZONE to change the time zone. The digits that are to be set are flashing. Press ▲/ZONE or ▼ change the value. Display order: MST > PST > AKT > HST > EST.

Alarm setting

Press the ALARM button. To turn the alarm on or off, press ▲/ZONE.
To set the alarm, hold the ALARM button. The digits that are to be set are flashing. Press ▲/ZONE or ▼ change the value. The setting order: Hour > Minute. Finally, press the ALARM button to save the settings and exit.
When the alarm sounds, press SET to activate the snooze function. The alarm will sound again in 5 minutes.
Press any key to exit.

Temperature units setting

Press the ▼ button to switch between °C and °F.

Specifications

Base station

Air humidity, units of measurement| % (RH)
Operating humidity range| 25… 99%
Temperature, units of measurement| °F, °C
Operating temperature range (indoors)| –0… +50°C (+32… +122°F)
Screen| monochrome
Power supply| 4 АА batteries (not included)
Dimensions| 362x236x28.5mm (14×9.2×1.1in.)
Sensor

The manufacturer reserves the right to make changes to the product range and specifications without prior notice.

Care and maintenance

Take the necessary precautions when using the device with children or others who have not read or who do not fully understand these instructions.
Do not try to disassemble the device on your own for any reason. For repairs and cleaning of any kind, please contact your local specialized service center.
Protect the device from sudden impact and excessive mechanical force.
Store the device in a dry, cool place away from hazardous acids and other chemicals, away from heaters, open fires, and other sources of high temperatures.
Operate the device only in a completely dry environment and do not touch the device with wet or damp body parts.
Only use accessories and spare parts for this device that comply with the technical specifications.
Check this device and its cables and connections for any possible damage before use.
Never attempt to operate a damaged device or a device with damaged electrical parts! Damaged parts must be replaced immediately by an authorized service agent.
If a part of the device or battery is swallowed, seek medical attention immediately.
Children should use the device under adult supervision only.

Battery safety instructions

Always purchase the correct size and grade of battery most suitable for the intended use. Always replace the whole set of batteries at one time; take care not to mix old and new ones or batteries of different types. Clean the battery contacts and also those of the device prior to battery installation. Make sure the batteries are installed correctly with regard to polarity (+ and –). Remove batteries from equipment that is not to be used for an extended period of time. Remove used batteries promptly. Never short-circuit batteries as this may lead to high temperatures, leakage, or explosion. Never heat batteries in order to revive them. Do not disassemble batteries. Remember to switch off devices after use. Keep batteries out of the reach of children, to avoid the risk of ingestion, suffocation, or poisoning. Utilize used batteries as prescribed by your country’s laws.

Levenhuk Warranty

Levenhuk products, except for their accessories, carry a 2-year warranty against defects in materials and workmanship. All Levenhuk accessories are warranted to be free of defects in materials and workmanship for six months from the purchase date. The warranty entitles you to the free repair or replacement of the Levenhuk product in any country where a Levenhuk office is located if all the warranty conditions are met.
For further details, please visit: www.levenhuk.com/warranty
If warranty problems arise or if you need assistance in using your product, please contact the local Levenhuk branch.

Levenhuk Inc. (USA): 928 E 124th Ave. Ste D, Tampa, FL 33612, USA,+1-813-468-3001, [email protected].
Levenhuk Optics s.r.o. (Europe): V Chotejně 700/7, 102 00 Prague 102, Czech Republic, +420 737-004-919, [email protected].
Levenhuk® is a registered trademark of Levenhuk, Inc. © 2006—2022 Levenhuk, Inc. All rights reserved. www.levenhuk.com