LINDY LH500XW Premium Headphones with Wireless Noise Cancelling User Manual
- June 5, 2024
- LINDY
Table of Contents
LINDY LH500XW Premium Headphones with Wireless Noise Cancelling User Manual
Introduction
Thank you for purchasing the LH500XW by Lindy. These wireless noise cancelling headphones have been developed to deliver superb quality Hi-Fi sound using advanced aptX® technology without the distraction of annoying background noise.
Product Contents
- LH500XW Headphones
- 3.5mm audio cable 1.5m
- 1/4’’ stereo-plug adapter
- Dual-plug flight adapter
- Micro USB charging cable 80cm
- Hard carry EVA case with mesh pouch
- User manual
Features and Benefits
Requires Voice Dialling support on mobile phone
Overview
Left
-
USB Socket (for charging)
-
Volume Down / Previous Song (Wireless only)
-
Multi-Function Button: On/Off, Pairing, Make/Answer/ End/Reject Call (Wireless only)
-
Volume Up / Next Song (Wireless only)
-
Microphone
-
3.5mm Audio Jack
-
Battery Indicator
Right
-
Volume Control Dial (Wireless, Noise Cancelling or Wired)
-
Noise Cancelling On/Off Switch
-
Noise Cancelling Indicator
Safety
- Check the volume level before placing the headphones over your ears
- Do not listen to the headphones at high volume for excessive periods as this may damage your hearing
- Discontinue use if you experience any discomfort or irritation from using the headphones
- These headphones must not be worn whilst driving a motor vehicle
Charging the Battery
- When the battery is low the LED (7) will flash red and an audio prompt (five beeps) will be heard through the headphones. If you’re using a compatible iOS device you can also see the status of the headphones battery on your device.
- Plug the supplied USB charging cable in to the charging port on the headphones (1).
- Plug the other end of the USB charging cable into the corresponding port on either a USB mains power supply or a PC.
- The LED indicator will light up red.
- Charging from empty will take approximately 3 hours.
- When the battery is fully charged, the LED indicator will switch from red to off.
Important! Make sure that the LH500XW are fully charged for at least 4 hours prior to initial use.
Operation
The LH500XW can be used in a number of different configurations to suit your needs; Wired, Wireless, Noise Cancelling and Passive. For optimum audio performance we recommend using the headphones with Noise Cancelling activated.
Noise Cancelling
- Adjust the volume of the LH500XW using the Volume Control Dial (8) to ensure the volume is not too high.
- Switch on the Noise Cancelling feature by sliding the On/Off Switch (9) to On, the Noise Cancelling Indicator (10) will illuminate Blue
- fter you turn the Noise Cancelling feature on you may hear a slight hissing noise, this is normal and will cease after a few seconds.
When using the Noise Cancelling feature, if the battery level becomes low the Noise Cancelling Indicator will become dim. If you continue to use the Noise Cancelling feature the battery will eventually drain, if you are using a wired connection you may still continue to use the headphones.
Pairing
- Switch on the Wireless function by pressing and holding the Multi Function Button (3). If no previously paired device is found within range, the LH500XW will automatically go into pairing mode and the LED Indicator will alternately flash Green and Red.
- Enable the Bluetooth function on your mobile phone or tablet.
- Navigate to the Bluetooth menu of your device and scan/search for new devices.
- When LH500XW is found select it and follow the on screen prompts. If you are prompted for a passkey or pin-code, please use 0000.
- You will see a notification on your portable device confirming that pairing and connection is complete.
Music Playback
Play/Pause Music| Press down the Multi-Function Button ( ) once to start
playing music and press it again to pause your music.
---|---
Play/Pause Music| Press the Music/Volume Forward ( ) Control button to play
the next song. To play the previous song, Press the Music/Volume Backward ( )
Control button.
Adjust Volume| Press and hold the Music/Volume Forward ( ) Control button to
increase the volume. To reduce the volume, Press and hold the Music/Volume
Backward ( ) Control button.
In addition the volume can be adjusted using the Volume Control Dial (8).
Call Related Functions
| Answer a call | Press the Multi-Function Button once to answer |
|---|---|
| End a call | Press the Multi-Function Button again to end |
| Ignore a call | Hold the Multi-Function Button for 3 seconds |
| Last number redial | Press the Multi-Function Button twice in standby status |
| Swap calls | Press the Multi-Function Button for 3 seconds |
Voice Dialling
The LH500XW can be used for voice dialling if this feature is supported on your mobile phone. Please refer to your mobile phone’s manual for more information. To use the voice dialling feature, press and hold the multifunction button and wait for the voice prompt before saying the name of the contact you want to call.
Technical Specification
- Bluetooth 4.1
- Supports A2DP/HFP/HSP/AVRCP profiles
- aptX® Bluetooth HD audio technology – CSR 8645 Chipset
- Battery Life:
- Up to 15 Hours Wireless Only
- Up to 30 Hours Noise Cancelling Only
- Up to 12 Hours Wireless & Noise Cancelling
- Charging Time Up to 3 Hours
- Noise Cancellation Rate: 85%
- Built in microphone for hands free calling
- Answer, Reject, End, Volume +/-, Track +/- & Play/Pause Control
- Dynamic Driver Diameter: 40mm Neodymium
- Range: up to 15m (open space)
- Frequency Response: 20Hz-20kHz
- Impedance: 32±15% Ohm
- Sensitivity (S.P.L.): 85db±3db SPL/1kHz (0dB SPL=20μPa)
- Nominal THD: >0.2%
Declaration of Conformity
We, LINDY Electronics LTD, hereby declare that the product(s)
LINDY LH500XW Wireless ANC Headphones
No. 73201
conforms to with the requirements of the following UK Legislation and EU Directives:
EU Directive 2014/53/EU (RE – Radio Equipment)
EU Directive 2014/35/EU (LVD)
The Restriction of the Use of Certain Hazardous Substances in Electrical and
Electronic Equipment Regulations 2012 / EU Directives 2011/65/EU, 2015/863/EU
amendment Annex II, Article 13 (RoHS II)
The following standards were used to evaluate the product:
ETSI EN 300 328 V2.2.2 (2019-07)
ETSI EN 301 489-1V2.2.3 (2019-11)
ETSI EN 301 489-17 V.3.2.3 (2020-07)
EN 62368-1: 2014/A11:2017
EN 50332-2:2013
EN 62479:2010
EN 50663:2017
BS EN IEC 63000:2018
Date: 28 January 2021
Signature:
Name: Darren N. Casey
Position: Managing Director, LINDY Electronics LTD
Lindy Supplier Office Reference: 19.01.21
LINDY Electronics Limited
Sadler Forster Way | Teesside Industrial Estate | Thornaby, Stockton-on-Tees |
TS17 9JY, England
General T +qq 16142 7514000 I F +LILI 16L12 7514031 I
sales@lindy.co.uk
Accounts T +LILI 16142 7514035 | F +LILI 16412 75L1031 |
accounts@lindy.co.uk
Co. Reg No. 02132710 (Registered office as above) | Vat Reg No. GB LI72 0100
00
CE Declaration of Conformity
LINDY-Elektronik GmbH hereby declares that the product(s)
LINDY Bluetooth Headphones / Bluetooth Kopfhorer LHSO0XW (EU) No.: 73201
is in conformity with the requirements of the following EU Directives:
EU Directive 2014/53/EU (RE — Radio Equipment)
EU Directive 2014/35/EU (Niederspannungsrichtlinie I LVD )
EU Directives 2011/65/EU, 2015/863/EU Amendment Annex II, Article 13 (RoHS II)
The following Standards were used to evaluate the product(s):
ETSI EN 300 328 V2.2.2 (2019-07)
ETSI EN 301 489-1 V2.2.3 (2019-11)
ETSI EN 301 489-17 V.3.2.3 (2020-07)
EN 62368-1:2014/A11:2017
EN 50332-2:2013
EN 62479:2010
EN 50663:2017
EN IEC 63000:2018
Dr. Rainer Bachmann
Head of Global Product Compliance
Mannheim, 28.01.2021
Ref. LINDY S-Office: 720600 19012021
Manufacturer (EU):
Lindy-Elektronik GmbH
Markircher Str. 20
68229 Mannheim
Germany
T +49 621 470050
info@Lindy.de
Manufacturer (UK):
Lindy Electronics Ltd.
Sadler Forster Way
Stockton-on-Tees
TS17 9JY, England
T +44 1642 754000
sales@Lindy.co.uk
FCC Certification
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation.
You are cautioned that changes or modification not expressly approved by the
party responsible for compliance could void your authority to operate the
equipment. This device complies with part 15 of the FCC Rules. Operation is
subject to the following two conditions:
- This device may not cause harmful interference, and
- This device must accept any interference received, including interference that may cause undesired operation.
Recycling Information
WEEE (Waste of Electrical and Electronic Equipment), Recycling of
Electronic Products
Europe, United Kingdom
In 2006 the European Union introduced regulations (WEEE) for the collection
and recycling of all waste electrical and electronic equipment. It is no
longer allowable to simply throw away electrical and electronic equipment.
Instead, these products must enter the recycling process. Each individual EU
member state has implemented the WEEE regulations into national law in
slightly different ways. Please follow your national law when you want to
dispose of any electrical or electronic products. More details can be obtained
from your national WEEE recycling agency.
For Home and Office use Tested to Comply with FCC Standard
Lindy No 73201
1st Edition, January 2021
Lindy.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>