Fellowes 120C-2 Powershred Confetti Cut Shredder User Manual
- June 17, 2024
- Fellowes
Table of Contents
**Fellowes 120C-2 Powershred Confetti Cut Shredder User Manual
**
Product Profile
This product is built to shred paper, staples, small paper clips and credit cards. It is not built to shred adhesive labels, transparencies, newspaper, cardboard, large paper clips, or plastic (other than credit cards). Attempting to shred items not intended for this shredder may cause damage.
| Strip-Cut| Strip-cut| Confetti-cut
---|---|---|---
(120 – 2)| (120 – 2)| (120C- 2)
Sheet capacity*| 18-20 sheets| 16-18 sheets| 12-14 sheets
Paper shred size| 5,8 mm| 3,9 mm| 3,9 x 25 mm
Maximum paper width| 241 mm| 241 mm| 241 mm
Recommended daily capacity| 4,000 sheets| 4,000 sheets| 2,000 sheets
Based on A4 (70 g/m2) paper with shredder operating at rated voltage; heavier paper, high humidity, or other than rate voltage may reduce sheet capacity.
IMPORTANT SAFETY INSTRUCTIONS READ ALL INSTRUCTIONS BEFORE USING
While setting up shredder
-
Check shredder for damage or defects; some paper particles in the basket are normal due to product testing and does not indicate a defect.
-
Avoid touching exposed blades on underside of confetti-cut shredder head.
-
Plug power cord in an outlet that can easily be reached. The plug is the primary electrical disconnect.
-
Make sure the electrical rating listed on the serial label (located inside, just below top of
shredder) matches the available electric power. -
Do not place shredder near or over a heat or water source
While operating shredder
- Keep hands and hanging objects (jewelry, ties, loose clothing, long hair, etc.) away from paper entry.
- Keep children and pets away from the shredder
When not in use
- Always turn off and unplug shredder.
- Unplug before emptying basket.
- Do not open shredder head: Danger of electric shock. Opening shredder head will void the warranty.
NOTE : Do not use flammable synthetic oil, petroleum-based products or aerosols of any kind on or near product at any time
Set-Up
-
Turn retractable feet (D) to outward position. This will improve stability. The feet should be turned outward if shredder will not be placed between furniture.
-
Pull waste basket drawer (A) completely out of cabinet.
-
Put waste bag in basket (sample bags provided). Allow edges to overhang. Contact Fellowes to order more bags. (Part #36054).
-
Slide waste basket drawer (A) into cabinet. The shredder will not operate if drawer is not
pushed all the way into cabinet. -
Plug power cord into a convenient outlet.
Operation
Control Switches
Control Switch (E)
AUTOMATIC
Turns on the automatic-start sensor and the green Ready light.
O OFF
Turns off the automatic-start sensor and the green Ready light
R REVERSE
Runs shredder in reverse mode. Press and hold to activate.
Manual Forward Button (G)
Runs shredder when button is held down.
Troubleshooting Lights
Ready Light (F) (Green)
Shredder is in automatic start mode.
Basket Ajar (H)
Waste basket drawer is open.
Basket Full (I)
Waste basket is full or paper has collected under cutting cylinders.
Paper Jam (J)
Shredder is jammed (e.g., too much paper fed at one time).
For convenience and energy savings, your shredder is equipped with an automaticstart sensor (K). This means that when the control switch (E) is in the automatic [I] position, the shredder will start running when you put paper into it and stop a few seconds after the paper has passed through.
CAUTION : The automatic-start sensor cannot tell the difference between paper and other objects. This feature can also be a hazard. Always turn off the shredder when it is not in use. Unplug the shredder if it will not be used for an extended period
To shred
- Press control switch (E) to automatic [I] position. Green ready light (F) should turn on.
- Feed paper straight into entry (C), releasing when shredder begins shredding; see Product Profile for limits on paper width, shred able items, sheet capacity, etc.
To empty waste basket
If basket full light (I) is on, follow these steps until light turns of
-
Press manual forward button (G) to finish shredding any paper in paper entry.
- Press control switch (E) to the off [O] position.
- Open the waste basket drawer (A) and remove full bag.
- Place new bag in basket, then slide drawer into cabinet.
-
Press and hold control switch (E) in the reverse [R] position for a few seconds to clear paper shreds that have collected under cutting cylinders.
- Alternate between manual forward (G) and reverse [R] for a few seconds in each
position.
CAUTION : The shredder may be damaged if you alternate too rapidly between forward and reverse
- Alternate between manual forward (G) and reverse [R] for a few seconds in each
-
Unplug shredder and remove wastebasket drawer (A).
- Carefully clear any paper shreds that have collected on under side of paper entry (C).
CAUTION : Model 120C-2 (confetti cut model) has exposed blades. Use care when
removing paper shreds on underside of paper entry
- Carefully clear any paper shreds that have collected on under side of paper entry (C).
To clear a paper jam
If paper jam light (J) is on, follow these steps until light turns off.
-
Check the waste basket and empty if full.
-
Press and hold control switch (E) in the reverse [R] position to back paper out of paper
entry (C). Try pulling gently on paper to remove it from shredder. -
Alternate between forward and reverse, if needed:
- Press and hold manual forward button (G) for a few seconds.
- Press and hold control switch (E) in the reverse [R] position for a few seconds.
- Continue alternating between forward and reverse until the jam clears.
CAUTION : The shredder may be damaged if you alternate too rapidly between forward and reverse
Maintenance
Empty waste basket regularly to ensure the smooth functioning of the cutting
cylinders. The shredder will not operate when the basket is full.
Oil confetti-cut model (120C-2) regularly to ensure proper operation.
If used at or near daily capacity, apply oil every time you empty the basket.
Use Fellowes Powershred Lubricant #35250 or other non-aerosol vegetablebased
oil in a long-nozzle container (sample oil provided).
CAUTION: Do not use flammable synthetic oil, petroleum-based products, or
aerosol
lubricants of any kind
To oil the cutting cylinders
- Apply oil over full width of cutting cylinders through the paper entry (C).
- Press and hold the manual forward button (G) for at least 3 seconds.
- Press and hold the control switch (E) in reverse [R] for at least 3 seconds.
- Repeat the forward/reverse sequence 3 or more times.
Troubleshooting
If there is a problem with your shredder, check these symptoms and remedies.
If you cannot solve the problem, call your local dealer or contact Fellowes
directly. Do not open shredder head to attempt repair. You could be exposed to
serious electric shock and will void the warranty.
Symptom | Remedy |
---|---|
Ready Light (F) will not light | Make sure shredder is plugged in and the |
control switch (E) is in the automatic [I] position
Shredder does not start or stops while shredding|
- Make sure shredder is plugged in and control switch (E) is in the automatic [I] position.
- Shredder is jammed. Follow the instructions under Operation
Basket ajar light (H) is on | Make sure the waste basket drawer (A) is all the
way into the cabinet.
Basket full light (I) is on | Empty the waste basket. Follow the instructions
under Operation
Paper jam light (J) is on | Clear the paper jam. Follow the instructions under
Operation.
Confetti-cut shredder (120C-2): Shredder sheet capacity decreases, noise level
increases, or cutting cylinders stop with a squeak or rubbing sound| Oil the
cutting cylinders. Follow the instructions under Maintenance.
Shredder runs for a few seconds after the paper has cleared the cutters| No
action required. This is a self-cleaning function.
Supplies
The following items for the 120-2 and 120C-2 shredders are available from
Fellowes:
Item | Quantity | Part Number |
---|---|---|
Waste bags (in dispenser) | 50/roll | 36054 |
Waste basket (box) | 1 box | 400008 |
Powershred Lubricant (120C-2 only) | 12 oz. bottle | 35250 |
To purchase supplies, contact Fellowes at the appropriate location listed on
the back
page of this instruction manual, or visit us at
www.fellowes.com
Fellowes conducts extensive testing to ensure that these shredders are capable of meeting all of the specifications listed in the Product Profile (see page 3). However, the actual sheet capacity is dependent on a number of factors including the type and weight of paper, the humidity, the voltage level of the power source, the temperature of the motor, and the care with which the operator feeds the paper. Safety agency testing is conducted to ensure that the shredder will operate to specifications even if the available voltage is 10% below or 6% above the rated voltage. During this testing 2.5 minutes was taken to empty the basket each time it filled and the following capacities were used for temperature rise testing:
Voltage| Hertz| Cut Size & Type| Number of Sheets|
Paper Size & Weight
---|---|---|---|---
220-240 VAC| 50 Hz| 3,9 mm Strip Cut| 17| A4 70 g
220-240 VAC| 50 Hz| 5,8 mm Strip Cut| 19| A4 70 g
220-240 VAC| 50 Hz| 3,9 mm Confetti Cut| 13| A4 70 g
120 V| 60 Hz| 5,8 mm Strip Cut| 19| 8.5×11 20 lb
120 V| 60 Hz| 3,9 mm Confetti Cut| 13| 8.5×11 20 lb
100 V| 50/60 Hz| 3,9 mm Strip Cut| 17| A4 70 g
100 V| 50/60 Hz| 3,9 mm Confetti Cut| 13| A4 70 g
Limited Warranty
Fellowes, Inc. (“Fellowes”) warrants the cutting blades of the machine to be
free from defects in material and workmanship for 20 years from the date of
purchase by the original consumer. Fellowes warrants all other parts of the
machine to be free of defects immaterial anorkmanship for 2 years from the
date of purchase by the original consumer. If any part is found to be
defective during the warrant period, your sole unexclusive remedy will be
repair or replacement, at Fellowes’ option and expense, of the defective part
This warranty does not apply in cases of abuse, mishandling or unauthorised
repair.
ANY IMPLIED WARRANTY, INCLUDING THAT OF MERCHANTABILITY OR FITNESS FOR
A PARTICULAR PURPOSE, IS HEREBY LIMITED IN DURATION TO THE APPROPRIATE
WARRANTY PERIOD SET FORTH ABOVE. In no event shall Fellowes be liable for any
consequential or incidental damages attributable to this product. This
warranty gives you specific legal rights. You may have other legal rights that
vary. The duration, terms and conditions of this warranty are valid worldwide,
except where different limitations, restrictions or conditions may be required
by local law
For more details or to obtain service under this warranty, please contact:
EUROPEAN CONSUMER HELPLINE
00 800 1810 1810
(Accessible via most major telephone networks)
OR the nearest Fellowes location listed on the back page of this user manual. Warrantor: Fellowes, Inc.
Declaration of Conformity
Fellowes
Yorkshire Way, West Moor Park,
Don caster, South Yorkshire, DN3 3FB England
declares that the product
Models 120-2 and 120C-2
conform with the requirements of the Low Voltage Directive (73/23 EEC) and the
Electromagnetic Compatibility Directive (89/336 EEC) and the following
harmonized
European Norms (EN Standards) and IEC Standards.
Safety | EN60950 ‘Information Technology Equipment |
---|---|
EMC | Standard |
EN 61000-4-2: 1995 | 3AD, 2CD |
EN 61000-4-4: 1995 | v |
EN 61000-4-5: 1995 | 2DM, 3CM |
EN 61000-4-6: 1996 | 2 |
EN 61000-4-11: 1994 | per table 13 |
EN55014-1:2000 | |
EN 61000-3-2;1995 | Class A |
+A1: 1998, +A2: 1998, +A14:2000 | |
EN 61000-3-3:1995 | |
+A1:2001 |
Itasca, Illinois, USA 2 September 2002
Anthony Stories
All European Countries
European Consumer Helpline
00 800 1810 1810
(Accessible via most major telephone networks)
France + 33 (0) 2-99-22-71-22
Germany + 49 (0) 5131-4977-0
Italy + 39 (0) 071-730041
Poland + 48-22-837-7356
The Netherlands + 31 (0) 347-377988
United Kingdom + 44 (0) 1302-836836
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>