Shenzhen Galime Electronics Technology 40C46B Smart Motor Curtain Kit Instruction Manual

Shenzhen Galime Electronics Technology 40C46B Smart Motor Curtain Kit

Motor wiring instructions

Five-core wire connection: t can realize strong current control, regardless of whether the strong current control line has electricity or not, it can realize remote control dry contact control, and pull start functions
Note: The voltage of the strong current control line is AC90-240V 50/60HZ When the red wire is connected and the black wire is disconnected. the motor rotates farward; when the black wire is connected and the red wire is disconnected, the motor reverses when both the black and red wires are disconnected, the motor stops

Motor button description

Weak current control wiring

Enter setting state

Learn code

Restore factory settings (clear code)

Reverse Settings

FCC Warning

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions

1. this device may not cause harmful interference.
2. this device must accept any interference received, including interference that may cause undesired operation.

This device has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This device generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this device does cause harmful interference to radio or television reception, which can be determined by turning the device off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the device and receiver.
• Connect the device into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help

Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment

DIV Curtain Track Assembly

Curtain model

1. Finish lenght= wall to wall-(1 to 4)CM
2. Wall mounting finish lenght= window size + 20CM

• Step 1 The belt passes through the main gearbox and the track completely. Please note that the track cannot be inserted into the main gearbox.
• Step 2 Both of the end belt divide to show 7 teeth of the track. Then cut it Please note that the track can not be inserted into the main gearbox
• Step 3: Press on the gearbox, take out the belt, line up the end, make the mark,
• 
• Step 4 At the end of belt, install the belt clamp. ock the belt
• Step 5 After installing the belt clamp, install the first carrier assembly Please note that the carrier assembly direction
• Step 6: After the assembly of the carrier, slide it into the track.
• Step 7: Pull out the belt about 10-15cm from the main gearbox side, make the second mark with 10 tooth space from the first mark
• Step 8: Install the belt clamp and carrier assembly Please note that the carrier assembly direction
• Step 9 Assemble the corresponding accessories: runners, buffers, and track locker. The standard quantity of runners: 8 pcs/1meter, and so on.
• • Step 10: After the accessories are put in, tighten the screws of the track locker The part of the main gearbox is assembled
• Step 11 Pass the belt through vice gearbox then install the clamp and second carrier assembly. Please note that the direction of the first carrier must be consistent.
• • Step 12: After installing the second carrier, please be sure to insert the pin to fix.
• Step 13: Install the carrier arm and other components, then tighten the carrier screw Put it into track locker and, tighten the screw The part of vice gearbox is assembled.
• Step 14: Install top mount bracket, Standard quantity of top mount bracket: 2pcs/1meter, and so on.

SERVICE

• During the free warranty period, if the product breaks down during normal use,we will offer free maintenance for the product.
• Natural disasters/man-made equipment failures, disassembly and repair without the permission of our company, no warranty card, products beyond the free warranty period, etc., are not within the Scope of free warranty.
• Any commitment (oral or written) made by the third party (including the dealer/ service provider) to the user beyond the warranty scope shall be executed by the third party
• Please keep this warranty card to ensure your rights
• Our company may update or change the products without notice. Please refer to the official website for the updates.

RECYCLING INFORMATION

All products marked with the symbol for separate collection of waste electrical and electronic equipment (WEEE Directive 2012/19/EU) must be disposed of separately from unsorted municipal waste.To protect your health and the environment, this equipment must be disposed of at designated collection points for electrical electronic equipment designated by the government or local authorities. Correct disposal and recycling will help prevent potential negative consequences for the environment and human health. To find out where these collection points are and how they work, contact the installer or your local authority.

WARRANTY CARD

• Product information
• Product Name
• Product Type
• Purchase Date
• Warranty Period
• Dealer Information
• Customer’s Name
• Customer Phone
• Customer Address

Maintenance Records

Subscribe here

Please read the instruction manual carefully before using the product

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>