LISEN YY230908 Car Magnetic Wireless Charging Stand User Manual
- June 1, 2024
- Lisen
Table of Contents
Car Magnetic Wireless
Charging Stand
>
2E799
Thanks for choosing Lisen! To bring you a fantastic experience, please read the manual before using.
ACCESSORY LIST
Wireless charger body X 1 Positioning cards X 1
Magnetic lead sheets X1 Protective film X1
Hurricane outlet chuck X 1 A to c cable 1m X 1
Cleaning kit X 1
PRODUCT PARAMETER
NAME
LISEN CAR MAGNETIC WIRELESS CHARGING STAND
MODEL
2E799
MATERIAL
ABS/SILICA GEL
INPUT
5V/2A 9V/2A
OUTPUT
5W/7.5W/10W/15W
SIZE
68.411538MM
WEIGHT
82G
APPLICABLE POSITION
AIR OUTLET
SUPPORT BAR ADJUSTMENT STROKE
10MM
HOOK TELESCOPIC STROKE
30MM
OUTLET BLADE WIDTH
11-28MM
THICKNESS OF AIR OUTLET BLADE
<4.5MM
PRODUCT DESCRIPTION
- LED Light Display: When the power is on, the logo remains in a light blue constant glow. When wirelessly charging, the brightness decreases by 50%.
- When triggering FOD (Foreign Object Detection) metal detection, the lights will flicker.
COMPATIBLE DEVICES
- Headphones: Airpods pro (with magsafe battery compartment) / Airpods pro 2nd generation
- iphone 12/13/14/15 series bare phone/ phone case with magsafe function/ third party case without magsafe need to increase the magnetizer (refer to the following tutorial)
- With wireless charging does not support magsafe mobile phones, need to use the magnetizer (refer to the following tutorial)
- Without wireless charging mobile phone, need to use the magnetizer (only the car mount function, no wireless charging function)
INSTALLATION STEPS FOR THE USE OF AIR OUTLET HOOK CLIPS.
1.Loosen the fixing nut in a counter-clockwise direction.
2.Insert the swivel ball into the bolt.
3.Tighten the fixing nut.
Turn the hook clip adjustment knob counter-clockwise to adjust the hook length
to the maximum.
(1) If the support ring is obstructed, you can rotate the support ring to fit your air outlet.
(2) If your air vent is small in size and it is inconvenient to install the support ring, you do not need to use the support ring.
Snap the hook clip into the air outlet of the car and turn the hook clip adjustment knob to lock the blade.
To remove, loosen the hook and clip adjustment knob and detach the holder from the blade. (The blades should be kept horizontal so that they are perpendicular to each other and to the surface of the air outlet)
When adjusting the angle of use, slightly loosen the nut and adjust it to a comfortable angle before tightening the nut.
Hint: The uneven surface of mobile phone cases, liquid silicone cases, oil- painted cases and fabric leather cases are not suitable for this magnetizer.
If your case does not have the magsafe function, please follow the steps below to attract the magnetic sheet to achieve the magnetic suction function first.
Place the magnetic plate locator on the back of the phone/case, aligning the edges of the phone to ensure the top and bottom scale/left and right scales are the same; remove the protective film from the magnetic plate and stick it to the centre of the magnetic plate locator.
TUTORIAL ON THE USE OF THE LEAD MAG-NET:
1.Open the tissue pack and wipe the back of the phone/case with a damp tissue first, then dry it with a dry tissue.
2.If the mobile phone (case) is made of glass or if you do not want to stick the magnet attractor directly to the mobile phone (case), you can use the PE film first, peel off the PE film and stick it on the back of the mobile phone/case in the centre.
3.Place the film on the back of the phone. Observe that the positioning film has the same symmetrical edge to ensure that the ring is positioned in the middle of the phone.
4.Remove the protective film from the back of the ring. Place the film in the middle of the case and press gently with your hand. Make sure t- hat the ring is positioned in the middle of the film. Remove the positioning film; press it for about 5 seconds and leave it for 6 hours.
NOTE
1.About using non-standard car charger: please use QC3.0 or PD18W or above.
2.3.Metal accessories (iron pieces, finger clasps) or credit cards can interfere with charging. Cases containing metal, such as Pitaka, Evutec and Spigen QNMP, will trigger foreign object detection and interrupt charging.
3.5.Using the phone for GPS navigation or listening to music while charging can significantly affect the charging speed. When using GPS applications, the power consumption may be higher than the charging speed.
4. It is normal to have slight heating during the use of the wireless charger, if you encounter serious heating, please suspend the use and contact our after-sales mailbox.
PRODUCT WARNINGS
ISED CANADA STATEMENT:
This device contains licence-exempt tasmittre(s)/receiver(s)/ that comply with
Innovation Science and Economic Development Canada ‘s licence-exempt RSS(s).
Operation is subject to the following two conditions:
1)this device may not cause interference and
2)this device must accept any interference, including interference that may
cause undesired operation of the device.
Radiation Exposure: This equipment complies with Canada radiation exposure
limits set forth for an uncontrolled environment
RF Exposure Statement
To maintain compliance with IC’s RF Exposure guidelines, This equipment should
be. installed and operated with minimum distance of 10mm the radiator your
body. This device and its antenna(s) must not be co-located or operation in
conjunction with any other antenna or transmitter.
FCC WARNING:
This equipment generates uses and can radiate radio frequency energy and, if
not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment
does cause harmful interference to radio or television reception which can be
determined by turning the equipment off and on, the user is encouraged to try
to correct the interference by one or more of the following measures:
–Reorient or relocate the receiving antenna.
–Increase the separation between the equipment and receiver
–Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
–Consult the dealer or an experienced radio/TV technician for help
This equipment must be installed and operated with a minimum distance of 15 cm
between the radiator and user body.
AFTER SALE SERVICE
Lisen always dedicates to bring great shopping experience for each customer. Please feel free to contact us if you have any questions.
@LISEN Tech @LISEN
Tech
support@LISEN.com @LISEN
Tech
Shenzhen Xiangdangwen Technology Co., Ltd.
ADDRESS: 106, 1/F, No.313-4 Building Huachang Road,Langkou Community Dalang Street Longhua District, Shen-zhen, China.
MANUFACTURE: Huizhou Yimai Electronics Technology Co.Ltd.
ADDRESS: 3rd Floor, Building B, Hua-kai High-tech Industrial Park, Electro-nic City Road, Longxi Street,Boluo County.
Designed by LISEN
Made in China
AMZLAB GmbH Laubenhof 23, 45326 Essen
UKCA SERVICE LTD 21 Ellesmere Avenue,Worsley,Manchester,UK,M28 OAL
PHONE ACCESSORIES
Documents / Resources
|
LISEN YY230908 Car Magnetic Wireless Charging
Stand
[pdf] User Manual
YY230908 Car Magnetic Wireless Charging Stand, YY230908, Car Magnetic Wireless
Charging Stand, Magnetic Wireless Charging Stand, Wireless Charging Stand,
Charging Stand, Stand
---|---
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>