Texas HTX 4000 hedge trimmer User Manual

EQUIPMENT
User manual
HTX 4000 

Texas A/S – Knullen 22 – DK-5260 Odense S – Denmark
Tel. +45 6395 5555
www.texas.dk – post@texas.dk
Version 22.1

Warning symbols

| Warning:
Safety information about hazards that can result in personal injury
---|---
| Please read the user manual carefully before operating the machine.
| Use ear protection and eye protection
| Use shoes with non-skid soles
| Use work gloves
| Do not expose the equipment to rain/water and store it indoor.
| Do not expose to temperatures above 45  degrees C.
****| Must be recycled
| Do not expose the equipment to extreme heat or fire
| Do not expose the equipment to rain/water and store it indoor
| Please read the user manual carefully before operating the machine
| Must only to be used indoor
| Waste lithium batteries must not be disposed of with household waste. Batteries should be taken to your local recycling center for safe treatment.

We congratulate you with your new TEXAS hedge trimmer. We are convinced this machine will meet your expectations. To have the best result from your machine, you should read this manual carefully. This will spare you from any inconvenience. You must pay attention to the safety instructions, which are marked with this symbol:

Spare parts
Part list and drawings for the specific product can be found on our website www.texas.dk
If you help find part numbers yourself, it will ease the service.
For the purchase of spare parts, please contact your dealer.

General safety instructions

When using the hedge trimmer, the safety instructions must be closely followed. Read this manual carefully before starting the machine. Make sure that you know how to stop nd switch off the engine in case of accident. All instructions regarding safety and maintenance of the machine are for your own safety.
The warnings, precautions and instructions given in this manual, cannot cover all situations that the product can be placed in. The user must therefore present common sense and caution when using the product.

Safety in the work area

• Only use the product in clean and well lit areas
• Do not use the product in areas with explosive danger or where there is flammable fluids, gas or dust present.
• The person that uses the machine is responsible to other persons in the work area. Never use the machine when others, especially children or animals are near.
• This hedge trimmer is an electric product. It is therefore important, that it is never in contact with water or is used in wet surroundings.

Use and maintenance of the product

• A hedge trimmer must not be used for other work than as described in this manual.
• Only use original spare parts. Mounting of non-approved parts may lead to increased risk and are therefore not legal. Any liability is renounced for accidents or other damage that has happened due to the use of unauthorized parts.
• Before using the machine the dealer or other qualified person should instruct you in the use of the machine.
• Minors may not work the machine.
• The machine may only be lent to people who know how to work the machine. This manual should follow the machine under all circumstances.
• The hedge trimmer may only be used by persons who are rested, well and fit. If the work is tiring, frequent brakes should be made. Do not use the machine under influence of alcohol.
• Always check before start, that all bolts and nuts are tightened.
• Always wear eye protection when using the machine.
• Keep children and other persons at a distance of at least 5 meters from the work area.
• The battery should always be removed when:
  1. maintenance is made.
  2. the machine is left unattended.

Disposal
Waste electrical products must not be disposed of with household waste. This tool should be taken to your local recycling center for safe treatment.

Identification of parts

1. Battery
2. Lock for battery
3. Main switch
4. Safety switch
5. Trigger switch| 6. Rotatable handle lock7. Rear handle
8. Front handle
9. Front handle switch
10. Protective guard
11. Cutting blade
---|---

Assembly

1. Unpack all parts and lay them on a flat, stable surface.
2. Remove all packing materials and shipping devices, if applicable.
3. Make sure the delivery contents are complete and free of any damage. If you find that parts are missing or show damage do not use the product but contact your dealer. Using an incomplete or damaged product represents a hazard to people and property.
4. Ensure that you have all the accessories and tools needed for assembly and operation. This also includes suitable personal protective equipment.
5. Plug in the battery, by pushing it down until you hear a click
6. Remove the battery by push down the battery lock button and pull up
   NOTE: Always remove the battery before assembly and maintenance.

Battery

HTX4000 is delivered with both battery and charger.
Warning: Do not try to disassemble, short circuit or put it to extreme heat or fire, as it can
cause serious inquiry and permanent damage to the battery!

Charging

• Only use the original charger with art. no. 90066658 (standard charger) or 90066657 (quick charger).
• Before the battery is being used the first time, it is recommended to full charge it first.

The battery has an energy indicator. Press the button and a number of LED lighs will flash (Illustration 7):

• 4 lights: 100% battery power
• 3 lights: 75% battery power
• 2 lights: 50% battery power
• 1 light: Less than 25% battery power

Note: The indicator lights is only indicative indications, and is not accurate power indications.
Important: To protect the battery from total discharge, the machine will stop, when the battery is nearly empty.
The machine must not be started up again after the automatic shutdown, as it can damage the battery. The battery must be recharged before the work can continue.

Charging

A full charge takes around 75 min (2.5Ah battery).
An extra quick charger (30 min) is sold separately at your local dealer or at www.texas.dk
Art. no. 90066657.

• Only use the original charger, which is included with the product and do not try to charge another type of battery in the charger, other than the original battery with art. no. 90066660 (2.5Ah) or 90066659 (4.0Ah).
• Keep the charger in a dry and warm environment (10-25 degrees C) and only use it indoors. It should be connected to a normal 230V AC socket.
• Before the battery is being used the first time, it is recommended to charge it fully.
• The surface of the battery can become warm during charging. This is normal.
• Do not cover battery or charger during charging. Allow free ventilation of air.

Insert the battery into the slots of the charger and slide it into place until it locks.
There are 4 lights on the charger indicating the status and state of charge of the battery

• Constant red light: The charger is ready to charge, but no battery is connected
• Flashing red light: Battery fault or overheat (always let a warm battery cool off before charging it)
• Flashing green light: Battery is charging
• Constant green light: Batteri er fuldt oplades og skal fjernes fra opladeren.

Important: The charger will stop, when the battery is full. However, it is not recommended to leave the battery in the charger for more than 24 hours.
It is recommended to drain the battery completely and fully charge it whenever possible, as it can increase the health of the battery. But partial charge will not damage the battery.
To remove the battery from the charger, hold the button down and pull the battery out.
During winter storage, the battery should be partly charged and kept warm at 10-20degrees C. Make sure to keep ventilation holes clean and free from dirt.

Use

Before use, make sure that the battery (1) is fitted properly with the battery lock (2) in place.
To start the hedge trimmer, first press the main switch (3), so it lights green. Then hold the safety switch (4) and activate both the trigger switch (5) and the front handle switch (8).
For safety reasons, the hedge trimmer only works when both switches are activated (5+8)
Stop the hedge trimmer by releasing the trigger switch (5) or the front handle switch (8).
The free gab between the blade teeth is 23 mm, but to ensure enough power to cut each branch nicely and avoid the blade getting blocked, it is recommended to avoid branches
larger than 15 mm depending on the hedge type. Use a handsaw or pruning cutter to trim the larger branches

Rotatable rear handle

The rotatable handle has 3 positions. Spend some time finding the position that is right for you. The rotatable handle makes the work more ergonomically correct.
To change position pull the lock (1) and turn the handle (2). The trigger switch must not be activated when turning the handle, as it will prevent it to turn.

Tips and advice

Apart from hedges, the hedge trimmer may also be used for cutting bushes.
The best cutting effect is achieved when holding the blade at an angle to the hedge of approx. 15°.
The opposite rotating knives cut on both sides, and it is, therefore, possible to trim the hedge in both directions.
The sides of the hedge are trimmed using curve-shaped movements from the bottom and upwards.

Clothing

When using the machine, wear tight-fitting work clothes, strong working gloves, hearing protectors, eye protection and boots with non-skid soles.

Maintenance

Before any service and maintenance is done, the power must be disconnected, it means the battery is removed from the tool.

• Remove the battery before you clean and store the machine.

• For obtaining the best cutting results the knives must be cleaned and oiled regularly.
  Remove dirt with a brush and oil lightly.

• Use biodegradable oil.

• Clean the housing and other parts with a mild cleanser and a moist cloth. Never use aggressive cleansers or solvents.

• Prevent water from getting into the machine.

• Use the blade protection when the machine is stored.

Standard warranty terms and conditions

The warranty period is 2 years for private end users in EU countries. Products sold for commercial use, only have a warranty period of 1 year. The warranty covers the material and/or fabrication faults.
Normal wear and replacement of wearing parts (e.g. blade-knives/bar) are not covered by the warranty.
If the battery is not stored correct (frost-free and recharged before storage and after storage), the durability is only guaranteed for 6 months

Specifications

Declaration of conformity

Manufacturer
Texas Andreas Petersen A/S
Hereby certifies that the following 
HTX 4000
Is in compliance with the specifications of the following directives
Machinery directive: 2006/42/EC
EMC directive: 2014/30/EU
Noise directive: 2000/14/EC amended by 2005/88/EC
conforms with the following standards
EN 60745-1: 2009+A11: 2010, EN 60745-2-15: 2009+A1: 2010
EN 55014-1:2006+A1+A2, EN 55014-2: 2015
LwA: 94 dB(A) LpA: 81.3 dB(A) Ah: 2.1 m/s 2
Serial numbers: 2201620001 – 2412629999
Texas Andreas Petersen A/S Knullen 22 • DK-5260 Odense S
Responsible for documentationJohnny Lolk

Johnny Look
Managing Director

EQUIPMENT

Documents / Resources

| Texas HTX 4000 hedge trimmer [pdf] User Manual
HTX 4000 hedge trimmer, hedge trimmer
---|---
| TEXAS HTX 4000 Hedge Trimmer [pdf] User Manual
HTX 4000 Hedge Trimmer, HTX 4000, Hedge Trimmer, Trimmer

References

• Salg af havemaskiner - Texas A/S

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>