TEXAS GTX 4000 Trimmer and Brushcutter User Manual

TEXAS GTX 4000 Trimmer and Brushcutter

Specifications

• Product: GTX 4000
• Manufacturer: Texas A/S
• Address: Knullen 22, DK-5260 Odense S, Denmark
• Contact: Tel. +45 6395 5555, Email: post@texas.dk
• Website:www.texas.dk
• Version: 24.1

Product Usage Instructions

Safety Instructions

• Before operating the machine, carefully read the user manual to ensure safe usage.
• Always pay attention to safety symbols and warnings provided in the manual.
• Wear eye protection and shoes with non-skid soles.
• Avoid exposing the equipment to rain/water and store it indoors.
• Keep a safe distance from people and animals when using the equipment.
• Avoid exposing the equipment to extreme heat or fire.

Identification of Parts

• The GTX 4000 trimmer consists of various components including the battery, main switch, safety switch, handle, trimmer head, and more. Refer to the user manual for detailed part identification.

Assembly

• Follow the assembly instructions provided in the manual to correctly set up the trimmer for operation. Ensure all parts are securely attached before use.

Battery

• The GTX 4000 comes with a battery and battery charger. Follow the instructions for proper handling and charging of the battery.

Charging

• A full battery charge takes approximately 75 minutes (based on a 2.5Ah battery). Ensure proper charging to maximize the trimmer’s performance.

Operation

• Operate the trimmer according to the guidelines provided in the manual. Pay attention to safety precautions and adjust settings as needed for efficient use.

Adjustment

• Use the adjustment features of the trimmer to customize the cutting angles and heights based on your trimming needs.

Edging

• Utilize the edging function of the trimmer by following the instructions to achieve clean and precise edging results.

Storage

• After use, store the trimmer in a safe and dry place to prevent damage and ensure longevity. Follow the storage recommendations provided in the manual.

Frequently Asked Questions (FAQ)

Q: Where can I find spare parts for the GTX 4000 trimmer?

• A: Part list and drawings for specific products can be found on the Texas A/S website at www.texas.dk. For purchasing spare parts, please contact your dealer for assistance.

Q: How long does it take to fully charge the GTX 4000 battery?

• A: A full battery charge typically takes around 75 minutes for a 2.5Ah battery. Ensure proper charging to optimize trimmer performance.

Warning symbols

• We congratulate you on your new TEXAS trimmer. We are convinced this machine will meet your expectations.
• To have the best result from your machine, you should read this manual carefully.
• This will spare you from any inconvenience.
• You must pay attention to the safety instructions, which are marked with this symbol:

General safety instructions

• Follow the safety instructions for your trimmer. Read the manual before you start your machine.
• Always be sure you can stop and turn off the engine in case of an accident.
• Instructions regarding safety and maintenance are for your safety.
• Only use your trimmer for the type of work, which is described in this manual.
• Only use original spare parts and accessories. In case of an accident caused by the mounting of non-original spare parts, Texas cannot be held responsible.
• The person, who is working with the machine, is responsible for keeping other persons away from the working area. Never use the machine, when children or animals are nearby.
• Minors may not use the trimmer.
• The machine may only be lent out to persons, who are confident with the use of the trimmer. The manual shall always be enclosed.
• The trimmer must only be used by people, who are fit and in good shape. If the work is exhausting, take a break. Do not use the trimmer, if you are under the influence of alcohol or illegal substances.
• Before start, always check that all bolts are safely tightened.
• This trimmer is an electric product, and therefore it may never be in contact with water. It must not be used in a moist environment.
• Always wear proper protection wear, gloves, goggles, trousers, and boots.
• Watch out for rotating nylon lines Using the machine on steep slopes is dangerous!
• Only use the machine in places where it can be operated safely!

Disposal

• Waste electrical products must not be disposed of with household waste. This tool should be taken to your local recycling center for safe treatment.

Identification of parts

1. Battery
2. Lock for battery
3. Main switch
4. Safety switch
5. Trigger switch
6. Handle
7. Handle lock
8. Button to turn to edge function
9. Lock for telescopic shaft
10. Button for adjusting the angle
11. Guard
12. Knife
13. Plant protector
14. Trimmer head

Assembly

1. Unpack all parts and lay them on a flat, stable surface.
2. Remove all packing materials and shipping devices, if applicable.
3. Make sure the delivery contents are complete and free of any damage. If you find that parts are missing or show damage do not use the product but contact your dealer. Using an incomplete or damaged product represents a hazard to people and property.
4. Ensure that you have all the accessories and tools needed for assembly and operation. This also includes suitable personal protective equipment.
5. Plug in the battery, by pushing it down until you hear a click
6. Remove the battery by pushing down the battery lock button and pulling up

• NOTE: Always remove the battery before assembly and maintenance.

Mounting the guard

• Place the guard on the motor house and fix it with the 2 included screws.
• The knife on the side will shorten the nylon line if it becomes too long.
• The plant protector is mounted as shown in the 2 holes on the side of the motor housing.

Mounting the front handle

• To change the position of the handle, release the lock on the backside.
• The handle can be adjusted up and down.
• Choose a suitable position and lock it again.

Battery

• GTX4000 is delivered with both battery and charger.
• Warning: Do not try to disassemble, short circuit, or put it to extreme heat or fire, as it can cause serious inquiry and permanent damage to the battery!

Charging

• Only use the original charger with art. no. 90066658 (standard charger) or 90066657 (quick charger).
• Before the battery is used the first time, it is recommended to fully charge it first.
• The battery has an energy indicator.

Press the button and some LED lights will flash (Illustration 7):

• 4 lights: 100% battery power
• 3 lights: 75% battery power
• 2 lights: 50% battery power
• 1 lights: Less than 25% battery power
• Note: The indicator lights are only indicative indications, and are not accurate power indications.
• Important: To protect the battery from total discharge, the machine will stop, when the battery is nearly empty.
• The machine must not be started up again after automatic shutdown, as it can damage the battery.
• The battery must be recharged before the work can continue.

Charging

• A full charge takes around 75 min (2.5Ah battery).
• An extra quick charger (30 min) is sold separately at your local dealer or www.texas.dk Art. no. 90066657
• Only use the original charger, which is included with the product, and do not try to charge another type of battery in the charger, other than the original battery with art. no. 90066660 (2.5Ah) or 90066659 (4.0Ah).
• Keep the charger in a dry and warm environment (10-25 degrees C) and only use it indoors. It should be connected to a normal 230V AC socket.
• Before the battery is being used the first time, it is recommended to charge it fully.
• The surface of the battery can become warm during charging. This is normal.
• Do not cover the battery or charger during charging. Allow free ventilation of air.
• Insert the battery into the slots of the charger and slide it into place until it locks.
• There are 4 lights on the charger indicating the status and state of charge of the battery
• Constant red light: The charger is ready to charge, but no battery is connected
• Flashing red light: Battery fault or overheat (always let a warm battery cool off before charging it)
• Flashing green light: Battery is charging
• Constant green light: Batteri er fuldt oplades og skal fjernes fra opladeren.
• Important: The charger will stop when the battery is full. However, it is not recommended to leave the battery in the charger for more than 24 hours.
• It is recommended to drain the battery completely and fully charge it whenever possible, as it can increase the health of the battery. But a partial charge will not damage the battery.
• To remove the battery from the charger, hold the button down and pull the battery out.
• During winter storage, the battery should be partly charged and kept warm at 10-20 degrees C. Make sure to keep ventilation holes clean and free from dirt.

Use

• Before use, make sure that the battery (1) is fitted properly with the battery lock (2) in place.
• To start the grass trimmer, first press the main switch (3), so it lights green.
• Then hold the safety switch (4) and activate the trigger switch (5)
• Always hold both handles, when using the trimmer.
• Stop the trimmer by releasing the trigger switch (5).
• Allow at least 5 seconds for the spool to stop rotating.

Adjustment

• The length of the shaft can be adjusted. Turn the lock on the shaft to loosen it. Adjust the telescopic shafts so they fit and tighten the lock again.
• The angle of the trimmer head can be adjusted by pressing the yellow button (A).
• The optimal work position will often be a combination of setting the length and angle correctly. So, try different adjustments.

Edging function

The grass trimmer can be changed into an edge cutter in the following way:

1. Set the angle of the trimmer head (press the yellow button A) to the lowest position.
2. Press the yellow button (B) on the shaft and turn it 90 degrees.
3. The nylon line will now cut vertically toward the ground

Clothing

When using the machine, wear tight-fitting work clothes, strong working gloves, hearing protectors, and boots with non-skid soles.

Storage

• Store the trimmer dry and unavailable for children.
• It is recommended not to let it rest on the trimmer head.
• Hang it on a wall in the handle.

Cleaning

• When cleaning the trimmer, the battery must be removed, for safety reasons.
• Remove dirt and grass from the guard.
• Cleaning with water shall be done with a soft brush.
• Water must be kept away from electric parts.

Rewinding the spool

• Before any service and maintenance is done, the power must be disconnected, which means the battery is removed from the tool.
• The spool is supplied with a nylon line on it.

When need to rewind the spool with a new nylon line, follow these steps:

1. Press the two plastic parts to remove the bottom cover.
2. Cut a piece of nylon line (1.6 mm) of a maximum of 12 meters. (you may find it easier to practice with a shorter line length first)
3. Find the center of the line and loop it onto the notch on the spool (Fig. 1)
4. Wind the line around the spool in the direction indicated by the arrows. Keep each end of the line in its channel (no crossing).
   • Keep the line tight as you wind, so that the line is fitted nicely without crossing (Fig. 2).
   • Wrong winding can result in the trimmer head not working properly.
5. Wind the line until about 20 cm left in both sides.
6. Keep the line tight and fix both ends to the notches in the spool (Fig. 3).
7. Put the spool back in place and put the line ends through the holes on each side.
   • Pull both line ends when the spool is in place (Fig. 4).
8. Remount the bottom cover.

Spare parts

• Part list and drawings for the specific product can be found on our website www.texas.dk
• If you help find part numbers yourself, it will ease the service.
• For purchase of spare parts, please contact your dealer.

Specifications

EC Declaration of Conformity

• Tel. +45 6395 5555 –www.texas.dk – post@texas.dk

References

• Salg af havemaskiner - Texas A/S

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>