TEXAS EQUIPMENT CHX2000 Chain Saw User Manual

TEXAS EQUIPMENT CHX2000 Chain Saw

NOTE!
BATTERY AND CHARGER ARE NOT INCLUDED FOR SOLO MACHINES

Warning symbols

| Warning:
Safety information about hazards that can result in personal injury
---|---

| Please read the user manual carefully before operating the machine.

| Use ear protection, helmet and eye protection

| Always wear protective clothing intended for chainsaw use.

| Use work gloves.

| Do not expose the equipment to rain/water and store it indoor.

| Danger!
Beware of kickback!

| Wear safety shoes/boots and safety trousers with leg protection.

| Do not expose the equipment to extreme heat or fire

| Do not expose the equipment to rain/water and store it indoor

| Do not expose to temperatures above 45 degrees C.

| Must be recycled

| Waste electrical products must not be disposed of with the household waste. This tool should be taken to your local recycling center for safe treatment.

Safety

How to read the manual
Please read this instruction manual carefully, especially the safety warnings marked with the symbol:

When using the product, the safety instructions must be closely followed. Read this manual carefully before starting the machine. Make sure that you know how to stop and switch off the engine in case of accident. All instructions regarding safety and maintenance of the machine are for your own safety.
The warnings, precautions and instructions given in this manual, cannot cover all situations that the product can be placed in. The user must therefore present common sense and caution when using the product.

Safety in the work area

• Only use the product in clean and well lit areas
• Do not use the product in areas with explosive danger or where there is flammable fluids, gas or dust present.
• The person that uses the machine is responsible to other persons in the work area. Never use the machine when others, especially children or animals are near.
• This chainsaw is an electric product. It is therefore important, that it never comes in contact with water or is used in wet surroundings.

Use and maintenance of the product

• A chainsaw must not be used for other work than as described in this manual.

• Only use original spare parts. Mounting of nonapproved parts may lead to increased risk and are therefore not legal. Any liability is renounced for accidents or other damage that has happened due to the use of unauthorised parts. Before using the machine, the dealer or other qualified person should instruct you in the use of the machine.

• Minors may not work the machine.

• The machine may only be lent to people who know how to work the machine. This manual should follow the machine under all circumstances.

• The chainsaw may only be used by persons who are rested, well and fit. If the work is tiring, frequent brakes should be made. Do not use the machine under influence of alcohol.

• Always check before start, that all bolts and nuts are tigthened.

• Always wear eye protection when using the machine.

• Keep children and other persons at a distance of at least 5 metres from the work area.

• The battery should always be removed when:
  1. maintenance is made.
  2. the machine is left unattended

• Due to vibrations, long-term use can lead to white fingers. If your arms, hands or fingers grow tired – or if there are visible signs of white fingers, stop the machine immediately and take a long break so that you become fully rested. To avoid white fingers, do not operate the machine for more than 1.5 hours a day.

• During transport, the main switch must be switched off.

Identification of the machine and components

See Fig. 1

1. Saw chain
2. Bar
3. Knob
4. Sprocket cover
5. On/off switch
6. Fenders
7. Oil tank cap
8. Oil bottle
9. Battery pack bracket
10. Battery pack*
11. Lock-off button and speed regulating switch
12. Sprocket
13. Guide bolt
14. Tensioning pin
15. Indicator light

***** Battery/charger are not included for solo machines.

Unpacking and assembly

Always wear gloves, when working with the chain.

Chain and guide bar assembly

See Fig. 2-5

1. Loose nut on sprocket cover, and remove sprocket cover (Fig.2)
   

2. Place the chain (1) in the grove of the bar (2), pay attention to the correct running direction, as shown by the running direction symbol (Fig.3)
   

3. Place the chain links around the sprocket (12) and put the bar on such that the one locating pegs fit into the slotted hole of the bar. (Fig.4)
   

4. Fitting the cover (4) and tighten knob (3) on sprocket cover. (Fig.5)
   

Setting the chain saw tension

Before adjusting chain, make sure guide bar nuts are only finger tight. Also make sure adjusting block is in oval adjusting hole on guide bar. turn adjusting screw (Fig. 6) clockwise until all slack is out of chain. Note: there should be no gap between side likes of chain ad bottom of guide bar. wearing protective gloves, move chain around guide bar, chain should move freely. If chain does no move freely. Loosen chain by turning adjusting screw counterclockwise. After chain tension is correct , tighten guide bar nuts firmly. If not, guide bar will move and loosen chain tension. This will increase the risk of kickback, this can also damage saw, Note: a new chain will stretch, check new chain after first few minutes of operation. Allow chain to cool down.
Readjust chain tension. WARNING! Do not over tension the chain as this will lead to excessive wear and will reduce the life of bar and chain. Over tensioning also reduce the amount of cuts you should get.

Oil filling

Note: the chain saw is shipped without oil in it, the chain saw must never be used without oil or with an oil level that is below the indicator. Warning , always ensure that the chainsaw is switched off and the plug is removed from the power point before making any adjustments.

1. Remove oil cap. (Fig. 7)
   

2. Fill oil tank with chain Lubricating oil.

3. check the oil level periodically, through the oil level indicator(fig.8)
   

4. wipe off excess oil.

Note: it is normal for oil to seep when saw is not in use. Empty oil tank after each use to prevent seepage.

Battery

Not included for solo machines *****

To get the best performance of the chainsaw, it is recommended to use the 4.0 Ah battery.

Warning: Do not try to disassemble, short circuit or put it to extreme heat or fire, as it can cause serious inquiry and permanent damage to the battery!

Battery pack is not fully charged when delivered.

Charging

• Only use the original charger with art. no. 90063242 or 90063241.
• Before the battery is being used the first time, it is recommended to fully charge it first.

LED lights

|

Battery Pack

---|---
All LEDs are lit| Fully charged (75-100%).
LED 1, LED 2, LED 3 are lit.| The battery pack is 50%-75% charged
LED 1, LED 2 are lit.| The battery pack is 25%-50% charged.
LED 1 are lit| The battery pack is 0%-25% charged
LED 1 flashes| The battery pack is empty. Charge the battery.

Note: The indicator lights is only indicative indications, and is not accurate power indications.

Important: To protect the battery from total discharge, the machine will stop, when the battery is nearly empty.
The machine must not be started up again after automatic shutdown, as it can damage the battery.
The battery must be recharges before the work can continue.

Charger

A full charge takes around 60 min for 2.0 Ah batteries

and 120 min for 4.0 Ah battery.

• Only use the original charger*
• Do not try to charge other type of batteries in the charger, other than the original batteries with art. no. 90063245 (2.0 Ah) or 90063246 (4.0 Ah).
• Keep the charger in a dry and warm environment (10-25 degrees C) and only use it indoor. It should be connected to a normal 230V AC socket.
• Before the battery is being used the first time, it is recommended to charge it fully.
• The surface of the battery can become warm during charging. This is normal.
• Do not cover battery or charger during charging. Allow free ventilation of air.

Insert the battery into the slots of the charger and slide it into place until it locks.

There are 4 lights on the charger indicating the status and state of charge of the battery.

Status

| Charging
| Fully charged
| Evaluate
| Defective

Important: The charger will stop, when the battery is full. However, it is not recommended to leave the battery in charger for more than 24 hours.
It is recommended to drain the battery completely and fully charge it whenever possible, as it can increase the health of the battery. But partial charge will not damage the battery.

To remove the battery from the charger, hold the button down and pull the battery out.

Before winter storage, the battery should be fully charged and kept warm at 10-20 degrees C. Charge it every 3 months. Make sure to keep ventilation holes clean and free from dirt.
Store the charger indoor between 5-25 degrees C.

Chain lubrication

The chainsaw is equipped with an automatic lubrication system, which ensures the chain is always lubricated optimally. However, the system depends on chain oil in oil tank and regular cleaning.

The chainsaw is not supplied filled with oil. It is essential to fill with oil before use. Never operate the chainsaw without chain oil or at an empty oil tank level, as this will result in extensive damage to the product.

Chain life and cutting capacity depend on optimum lubrication. Therefore, the chain is automatically oiled during operation via oil outlet.

Check the automatic operation of the chain lubrication by pointing the tip of the switched –on saw towards a piece of paper laying on the ground, if a patch of oil appears and becomes larger, then the automatic oil function is working. If there are no traces of oil even though the oil tank is full. Then the automatic oil function is not working. If the automatic oil function is not working. Remove the chain bar and clean out the oil ways of the chainsaw and chain bar, on reassemble if the chainsaw is still not working take it to a autorised if the chainsaw is still not working take it to an autorised service centre

Use correct chain oil to avoid damage to the chainsaw.
Never use recycled/old oil.
Use of non-approved oil will invalidate the warranty.

Check oil level prior to starting and regularly during operation Fig. 8. Refill oil when oil level is low.

Use

Before use, make sure that the battery is fitted properly  with the battery lock in place. (9+10).
Remove the bar cover and hold the electric saw by its grip with hands. To start the chainsaw, press the lock off button (11) on the trigger switch. To stop the chain saw release the trigger switch. Warning: hold the electric chain saw with hands until the chain is completely still.

Adjust speed.

When the chain saw is normally started, the indicator light (15) is green, and the chain saw is running at low speed. Press the speed control button (11) again, the indicator light turns red, and the chain saw is running at high speed. Remarks: The working state of the chainsaw can be switched freely by pressing the speed control button. The indicator light shows green for low speed, and the indicator light shows red for high speed .

Kickback safety devices

This saw has a low-kickback chain and reduced kickback guide bar.
Both items reduce the chance of kickback. Kickback can still occur with this saw.

The following steps will reduce the risk of kickback.

• Keep solid footing and balance at all times.
• Do not let guide bar nose touch anything when chain is moving.
• Never try cutting through two logs at same time. Only cut one log at a time.
• Do not bury guide bar nose or try plunge cut (boring into wood using guide bar nose).
• Watch for shifting of wood or other forces that may pinch chain.
• Use extreme caution when re-entering a previous cut.
• Use low-kickback chain and guide bar supplied with this chainsaw.
• Never use dull or loose chain. Keep chain sharp with proper tension.

Clothing

When using the machine, wear tight-fitting work clothes, strong working gloves, hearing protectors, eye protection, safety boots with non-skid soles and protective trousers.

Tips and advices

Use the chainsaw only with secure footing.
The chain must be running at full speed before it makes contact with the wood.
Do not attempt to saw areas which are difficult to reach, or on a ladder.

Maintenance

Before any service and maintenance is done, the power must be disconnected, it means the battery removed from the tool.

• Remove the battery before you clean and store the machine.
• For obtaining the best cutting results the chain and guide bar must be cleaned and oiled regularly. Remove dirt with a brush and oil lightly.
• Use biodegradable oil.
• Clean the housing and other parts with a mild cleanser and a moist cloth. Never use aggressive cleansers or solvents.
• Prevent water from getting into the machine.
• Use the guide bar cover when the machine is stored.

Lubrication hole. Remove the guide bar and check that the lubrication hole is not blocked with sawdust or dirt. Lubricate with oil/grease.’

Guide Bar. Clean the nose wheel and chain groove of any dirt. If required, turn the guide bar over to evenly share wear. A worn guide bar can be hazardous to use and should therefore be replaced.

Chain. The chain should be filed regularly to ensure the best result.

1. Ensure that the guide bar is securely attached.
2. Use a round file (not supplied).
3. File all of the teeth with 3-4 strokes, so that they are uniform, as shown in the illustration.
4. The height of the teeth must be checked regularly, and if they are too high, they must be filed down using a flat file (not supplied).

Replacing saw chain / guide bar
Replace chain when cutters are too worn to sharpen or when chain breaks. Only use replacement chain type29 links, 0.3 pitch (Art. no. 450779).
Inspect guide bar before sharpening or replacing chain.
A worn or damaged guide bar is unsafe and should be replaced. A worn or damaged guide bar will damage the chain. It will also make cutting harder.

Specifications

Warranty terms and conditions

The warranty period is 2 years for private end users in EU countries. Products sold for commercial use, only have a warranty period of 1 year.
The warranty covers material and/or fabrication faults.

Restrictions and requirements

Normal wear and replacement of wearing parts are
NOT covered by the warranty.

Wearing parts, which are NOT covered for more than 12 months:

• Guide bar
• Chain
• Battery: If the battery is not stored correct (frostfree and recharged every 3 months), the durability
  is only guaranteed for 6 months.

If you start the chainsaw without adding chain oil, the guide bar and chain will be damaged and cannot be repaired and therefore not covered by the warranty.

The warranty does NOT cover damages/faults caused by:

• Lack of service and maintenance
• Structural changes
• Exposure to unusual external conditions
• If the machine has been improperly used or overloaded
• Wrong use of oil, gasoline or other liquid types, which are not recommended in this user manual
• Use of unoriginal spare parts.
• Other conditions where Texas cannot be held responsible.

Whether a case is a warranty claim or not is determined in each case by an authorized service center. Your receipt is your warranty note, why it should always be kept safe.

REMEMBER: The purchase of spare parts as well as any request for warranty repair, art. number (e.g. 90063XXX), year and serial number should always be informed.

***** We reserve the right to change the conditions and accept no liability for any misprints.

Troubleshooting

Chainsaw operates
intermittently| Battery not fitted correctly
Loose connection
Internal wiring defective
On/Off switch defective| Refit battery so it locks
Contact service agent
Contact service agent
Contact service agent
No chain lubrication| No oil in reservoir
Vent in oil filler cap clogged
Oil passage clogged| Refill oil
Clean cap
Clean oil passage outlet on machine (behind
guide bar) and clean the guide bar groove
Chain/guide bar overheats| No oil in reservoir
Vent in oil filler cap clogged
Oil passage clogged
Chain is over tensioned
Dull chain| Refill oil
Clean cap
Clean oil passage outlet
Adjust chain tension screw
Sharpen chain or replace
Chainsaw rips, vibrates,
does not saw properly| Chain tension too loose
Dull chain
Chain worn out
Chain teeth are facing in the wrong direction| Adjust chain tension screw
Sharpen chain or replace Replace chain
Reassemble with chain in correct direction

  EC Declaration of conformity

Manufacturer

Texas Andreas Petersen A/S

• Hereby certifies that the following
• Chainsaw battery

CHX2000

• Is in compliance with the specifications of the machine directive and subsequent modifications.

2014/30/EU

• Conforms with the following standards

EN 62841-1:2015+A11:2022, IEC 62841-1:2014, EN ISO 12100:2010 EN IEC 55014-1:2021, EN IEC 55014-2:2021

LwA:  1 00 dB(A) LpA: 89 dB(A)
Vibrations Ah: 2.89 m/s2 (K=1.5 m/s2)
Serial numbers: 2301901001 – 2512909999

Texas Andreas Petersen A/S
Knullen 22 • DK-5260 Odense S
30.11.2022

Responsible for documentation
Johnny Lolk

Johnny Lolk
Managing Director

Customer Service

Spare parts
Spare part drawings for the specific product can be found on our website www.texas.dk If you find the part numbers yourself, this will facilitate more rapid service.
For purchase of spare parts, please contact your dealer.

Texas A/S – Knullen 22 – DK-5260 Odense S – Denmark
Tel. +456395   5555 – www.texas.dk – post@texas.dk

References

• Salg af havemaskiner - Texas A/S

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>