TEXAS 90053034 Dumb Cart Wheelbarrow for Tractor User Manual

June 1, 2024
TEXAS

User manual
Vogn med tip

Dumb cartTEXAS 90053034 Dumb Cart Wheelbarrow for
Tractor Version 24.1

Warning symbols

| This is the safety alert symbol. It is used to alert you to potential personal injury hazards. Obey all safety messages that follow this symbol to avoid possible injury or death.
---|---
| Do not drive with the cart on slopes.
| Do not transport humans and animals in the cart.
| Do not use the tilt function if anybody is located behind the cart.
| The cart must not be towed behind a car.
| Maximum recommened load is 150 kg.

Illustrations

TEXAS 90053034 Dumb Cart Wheelbarrow for Tractor -
Illustrations

REF# Description Qty
1 Bottom Panel 2
2 Front Cross Brace 1
3 Tongue Support 1
4 Wheel Axle Support 2
5 Axle 1
6 Wheel / Tire 2
7 Latch Spring 1
8 Latch Spacer 2
9 Tongue Latch 1
10 Hitch Tongue 1
11 Hitch Pin Bracket 1
12 Rear Cross Brace 1
13 Rear Corner Bracket 2
14 Side Panel 2
15 Rear Corner Brace 2
16 Front Panel 1
17 Front Corner Brace 2
18 Tailgate Latch 2
19 Tailgate Pin 2
20 Tailgate 1
21 Flat Head Bolt M8x16 60
22 Flat Head Bolt M8x20 2
23 Ø8 Lock Washer 72
24 M8 Nut 72
25 M8x20 Hex Head Bolt 10
26 Ø16 Flat Washer 4
27 R- Pin 3
28 Hitch Pin 1
29 M6x90 Hex Head Bolt 1
30 M6 Nylon Lock Nut 1
31 M6 Nut 2
32 Ø6 Flat Washer 2
33 Large Ø6 Flat Washer 1

TEXAS 90053034 Dumb Cart Wheelbarrow for Tractor - Illustrations
2TEXAS 90053034 Dumb Cart
Wheelbarrow for Tractor - Illustrations 3TEXAS 90053034 Dumb Cart Wheelbarrow for Tractor -
Illustrations 4TEXAS 90053034 Dumb Cart Wheelbarrow for Tractor -
Illustrations 5TEXAS 90053034 Dumb Cart Wheelbarrow for Tractor -
Illustrations 6TEXAS 90053034 Dumb Cart Wheelbarrow for Tractor -
Illustrations 7

Safety precautions

How to read the manual
Please read this instruction manual carefully, especially the safety warnings marked with the symbol:
The warnings, cautions, and instructions outlined in this instruction manual cannot cover all possible conditions or situations that may occur. It must be understood by the operator that common sense and caution are factors which cannot be built into this  product and must be supplied by the operator.
General safety precautions
Do not at any time carry passengers sit or stand on the cart.
Do not allow children to play on, stand upon or climb in the cart.
Always inspect the cart before using to assure it is in good working condition.
Replace or repair damaged or worn parts immediately.
Always check and tighten hardware and assembled parts before operation.
Do not exceed equipment maximum load capacity of 150 kg.
Avoid large holes and ditches when transporting loads.
Be careful when operating on steep grades (hill) the cart may tip over.
ALWAYS operate at reduce speed in rough terrain, along creeks, ditches and on hillsides.
Do not operate close to creeks, ditches and public highways.
To avoid personal injury and/or equipment damage DO NOT EXCEED 8 KM/H.
Always use caution when loading and uploading the cart.
Only tow with recommended vehicles (Lawn/Garden Tractors and ATVs).
Always keep hands and feet clear from moving parts while operating the equipment.
Always clear and keep work area clean when operating.
Always wear safety gear, eye protection, gloves and work boots when operating the dump cart.

Identification of parts

See Fig. 1 + 2

1. Bottom panel (x2)
2. Front cross brace (x1)
3. Tongue support (x1)
4. Wheel axle support (x2)
5. Axle (x1)
6. Wheel / Tire (x2)
7. Latch spring (x1)
8. Latch spacer (x2)
9. Tongue latch (x1)
10. Hitch tongue (x1)
11. Hitch pin bracket (x1)
12. Rear cross brace (x1)
13. Rear corner bracket x2)
14. Side panel (x2)
15. Rear corner brace (x2)
16. Front panel (x1)
17. Front corner brace (x2)| 18. Tailgate latch (x2)
19. Tailgate pin (x2)
20. Tailgate (x1)
21. Flat head bolt M8x16 (x60)
22. Flat head bolt M8x20 (x2)
23. Ø8 lock washer (x72)
24. M8 nut (x72)
25. M8x20 hex bolt (x10)
26. Ø16 flat washer (x4)
27. R-pin (x3)
28. Hitch pin (x1)
29. M6x90 hex bolt (x1)
30. M6 nylon lock nut (x1)
31. M6 nut (x2)
32. Ø6 flat washer (x2)
33. Large Ø6 flat washer (x1)
---|---

Note: You may have extra nuts & bolts when finished.

Unpacking and assembly

Figur 1+2
Unpack the product and place all parts on a flat stable surface. Remove all packing material.

  • Check that all parts are intact and ok. Should some parts be missing or be damaged, then immediately contact the seller/dealer.
  • Make sure all accessory parts amd tools needed for assembly are prepared.

Figur 3
Attach the two bottom panels together and then attach the front cross brace using the M8x16 Flat Head Bolts, Ø8 Lock Washer and M8 Nut, and tighten.
Figur 4
Attach the tongue support to the bottom panels using using M8x20 Flat head Bolts, Ø8 Lock Washer and M8 Nut. Loosely tighten bolts.
Figur 5
Attach the bottom of the wheel supports to the main body using using M8x16 Flat Head Bolts, Ø8 Lock Washer and M8 Nut. Loosely tighten bolts. Do not install the top bolts of the wheel support assembly until the next step when installing the axle.
Figur 6
Loosely install the top bolts, lock washer and hex nut.
Attach tongue by sliding the axle through the wheel support until it reaches the center opening.
Align the holes in the tongue with the end of the axle and push the axle through the wheel support.
Center the axle and tighten the assembly completely using M8x20 Hex Bolts, Ø8 Lock Washers and M8 Nuts.
Figur 7
Slide a Ø16 flat washer onto axle and glide the wheel onto the axle.
Slip another Ø16 flat washer and secure with R-Pin.
Repeat steps for the other wheel.
Insert the tongue latch through the opening in the hitch tongue.
Place one latch spacer on each side of the tongue latch.
Insert M6*90 Hex Bolt through Ø6 Large Flat Washer and M6 Nylon Nut to connect hitch tongue and latch spacers. Only Loosely Tighten.
Attach spring, one end of spring to hitch tongue and one end of latch spring to the top hole in the tongue latch.
Figur 8
Attach hitch pin bracket to tongue using M8x20 Hex Bolt, Ø8 Lock Washer and M8 Nut. Fully tighten bolts.
Insert the Hitch Pin through Hitch Bracket and Tongue; use the R-Pin to hold in place.
Figur 9
Turn the dumb cart onto its wheels.
Attach the two rear corner bracket and the rear cross brace to the back of the of the bottom panels using M8x16 Flat Head Bolts, Ø8 Lock Washer and M8 Nut.
Figur 10
Line up the two center holes on the left and right side panels, attach to the main body using M8x16 Flat Head Bolt, Ø8 Lock Washer and M8 Nut.
Figur 11
Secure the side panels by bolting the rear corner brace to the outside of each of the side panels using M8x16 Flat Head Bolt, Ø8 Lock Washer and M8 Nut.
Figur 12
Attach the front panel to the front cross brace and side panels using M8x16 Flat Head Bolt, Ø8 Lock Washer and M8 Nut.
Figur 13
Install both front corner braces to the front of the panel using M8x16 Flat Head Bolt, Ø8 Lock Washer and M8 Nut.
Figur 14
Install the two tailgate latches on the inside of the tailgate using M8x16 Flat Head Bolt, Ø8 Lock Washer and M8 Nut on each side of the tailgate.
Insert the rear trailer pins at the bottom of the tailgate using Tailgate Pin, Ø6 Flat Washer and M6 Nut.
Line up the tailgate and push downward to lock in place.
Do not use the dumb cart before tightening all hardware.

Operation instructions

  1. DO NOT exceed rated capacity of 150 kg
  2. NEVER tow the dump cart with box raised.
  3. DO NOT over fill the utility dump cart. Overflow loads can cause the cart and towing vehicle to lose traction and skid out of control.
  4. ONLY fill the dump cart to a comfortable dumping load. Extremely heavy loads will be difficult to operate and dump.
  5. ALWAYS use the dump cart for its intended purpose.
  6. ONLY use approved vehicles when towing the dump cart (Lawn/Garden Tractors and ATVs)
  7. ALWAYS make sure that the tow vehicle and the combined weight of the operator MUST BE greater than the load of the cart weight for proper control.
  8. DO NOT use cart on public highways or roads.
  9. NEVER exceed 8 km/h when towing the dump cart.
  10. DO NOT make sharp turns that may cause the Lawn/Garden Tractor or ATV tires to rub against the utility dump cart.
  11. ALWAYS slow down before turning.
  12. ALWAYS use caution when backing the utility cart.
    To avoid the cart from “jack-knifing” always back up in a straight line.

Maintenance and storage

  • After each use clean material out of the cart box.
    Never allow material to remain in the utility dump cart for extended periods of time.

  • Rinse/dry inside and outside of the dump cart after each use. Before storing make sure the cart is clean and dry for years of trouble-free service

  • Store indoors or protected area during severe weather and winter months

  • Before operating make sure the tires have the RECOMMENDED TIRE PRESSURE 25-30 PSI.

  • Regularly grease axle and wheel bearing area or when needed.

  • Periodically check all fasteners for tightness.

  • Annually clean and lightly lubricate parts.

  • Use a glossy enamel spray paint to touch up scratched or worn painted metal surfaces.

  • When storing outside always keep the tongue lower to the ground so the cart is not level to allow moister to easily run off and not stand.

  • Never exceed load capacity rating of 150 kgs it will damage the utility dump cart.

Specifications

Art. no. 90053034
Load capacity Max 150 kg
Box and frame Steel
Inner dimensions 97x76x30 cm
Outer dimensions 147,5×82,5×75 cm
Wheel size 16” x 3,5”
Hitch type Pin style
Wheel pressure 25-30 PSI
Net weight 35 kg

Explosive view of parts

TEXAS 90053034 Dumb Cart Wheelbarrow for Tractor - Explosive view of
parts

REF# Description Qty
1 Bottom Panel 2
2 Front Cross Brace 1
3 Tongue Support 1
4 Wheel Axle Support 2
5 Axle 1
6 Wheel / Tire 2
7 Latch Spring 1
8 Latch Spacer 2
9 Tongue Latch 1
10 Hitch Tongue 1
11 Hitch Pin Bracket 1
12 Rear Cross Brace 1
13 Rear Corner Bracket 2
14 Side Panel 2
15 Rear Corner Brace 2
16 Front Panel 1
17 Front Corner Brace 2
18 Tailgate Latch 2
19 Tailgate Pin 2
20 Tailgate 1
21 Flat Head Bolt M8x16 60
22 Flat Head Bolt M8x20 2
23 Ø8 Lock Washer 72
24 M8 Nut 72
25 M8x20 Hex Head Bolt 10
26 Ø16 Flat Washer 4
27 R- Pin 3
28 Hitch Pin 1
29 M6x90 Hex Head Bolt 1
30 M6 Nylon Lock Nut 1
31 M6 Nut 2
32 Ø6 Flat Washer 2
33 Large Ø6 Flat Washer 1

Note: you may have extra nuts & bolts when finished.

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals