TEXAS El-Tex 750 Tiller Cultivator User Manual

TEXAS El-Tex 750 Tiller Cultivator

Specifications

• Model: El-Tex 750
• Manufacturer: Texas A/S
• Voltage: 230 Volt
• Frequency: 50 Hz
• Power: 750 Watt
• Cutting Width: 280 mm
• Cutting Depth: 220 mm
• Noise Level: 93 dB(A)
• Art. no.: EP-0 90406565

Spare parts

• Part list and drawings for the specific product can be found on our website www.texas.dk
• If you help find part numbers yourself, it will ease the service.
• For purchase of spare parts, please contact your dealer.

Safety instructions

• Read this manual carefully before using the machine so that you understand and can fully comply with all safety instructions and ways of operation.
• Children may not use the machine.
• If you feel sick, tired, or have been drinking alcohol or taking medicine you may not use the machine.
• Always use eye- and ear protection and solid footwear when using the machine. Avoid loose-fitting clothes.
• Make sure to good foothold and have good control of the machine when using it.
• Make sure that spectators are at least 10 m from where you start or use the machine.
• Do not use the machine near explosive fluids, gasses, or dust. The machine may make sparks that can ignite dust etc.
• Never start using the machine until the work area has been cleared. Make sure to have enough light.
• Any repairs except those that are described in this manual must be carried out by an authorized dealer. The machine must be turned off when repairs are carried out.
• Only use original spare parts for repairs.
• The machine must only be lent to persons who are familiar with the use.
• This manual should always follow the machine.
• The warnings, precautions, and instructions that are described in this user manual do not cover every condition situation, or eventuality that may arise. This means that the user must use common sense and exercise caution when using this product.

Waste electrical products must not be disposed of with household waste. This tool should be taken to your local recycling center for safe treatment.

Identification

Assembly

• Assemble the frame with the screws supplied.
• Fit the cable holders. (fig. 2)

Starting the engine

Connect the power and make sure that the cord is fitted correctly in the cable holder. (fig. 3)

• Start the machine by pressing the safety button A and then pull the handle B towards the frame. When the machine has started, release A.
• Stop the machine by releasing handle B (fig. 4)

Tips

• Do not start the machine until you are in the work area.
• Always have both hands on the machine.
• The blades will make the machine move forward. Let the blades sink slowly into the ground.
• When you want the machine to work in deep soil, the most effective way is to let the machine move forward one arm’s length. Then pull the machine back towards you. Then move forward again.
• The blades must always run at the highest speed. Make sure they are not overloaded.

Important:

• Do not use the cultivator, if the soil is very hard and dry. It can damage the gearbox. Use the cultivator in the spring, in late summer, or in autumn, when the soil is moist and soft.
• Use one of these work patterns when preparing an area for sowing. (fig. 5)

Blades

• If the blades are worn or break, they can be replaced. See fig. 6. Lack of maintenance will lead to poor cultivating results or overload of the engine. Always use gloves when working near the blades.
• The blades may only be replaced as a set. Remove the outer lock pin and the outer blades, then the inner lock pin and the inner blades. (fig. 6).

Lubrication

Important: Check and refill with grease after each 20 hours of operation.

Procedure:

• Place the machine on its right side. Clean around the filling hole to prevent dirt from getting into the machine when the plug is removed. (fig. 7)
• Fill up with new grease-type Multifak to the level of the rim. Fit the plug again.
• Spare part no. for Multifak grease: 90406565

Maintenance and storage

• After each use the machine should be cleaned completely for grass and dirt.
• If you plan not to use the machine for several months all metal parts should be oiled to prevent corrosion.
  Only use original spare parts.

Troubleshooting

b.   Remove possible blockages.

c.   The soil is too hard. Change the work depth and go slowly forward and backward several times. Do not restart for 15 min.

Abnormal noise level| Blades are blocked| Stop the engine and await com- complete stop. Remove the blockage.
Lack of grease| Contact local dealer
Loose bolts, nuts or safety equipment.| Tighten. Contact the local dealer, if the noise persists.
Abnormal vibrations| Blades broken or worn| Replace or contact the local dealer
Work depth too big| Use correct work depth.
Bad results| Work depth too low| Use correct work depth.
Worn blades| Replace or contact the local dealer

Specifications

Art. no. 90406565

FAQ

• Q: What should I do if the engine does not start?
  • A: Check for power supply issues, defective safety switch, or if the overheat protection is active.
• Q: Can I dispose of the product with household waste?
  • A: No, waste electrical products should be taken to a local recycling center for safe treatment.

CONTACT

• Texas A/S – Knullen 22 – DK-5260 Odense S – Denmark
• Tel. +45 6395 5555 – www.texas.dk – post@texas.dk

www.texas.dk

References

• Sprzęt ogrodniczy, maszyny ogrodnicze, sklep z kosiarkami | Poznań Krysiak
• Salg af havemaskiner - Texas A/S

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>