TEXAS Smart 3700 Lawnmowers User Manual
- May 15, 2024
- TEXAS
Table of Contents
User manual
Smart 3700
Smart 4400
Illustrations
Warning symbols
| Warning !
---|---
| Read the manual.
Store it for later use.
| Always remove the cable from the electric switch when not using the mover or
during repairs.
| Risk of flying objects. Keep bystanders away for minimum 10 meter.
| Waste electrical products must not be disposed of with the household waste.
This tool should be taken to your local recycling center for safe treatment.
| Keep hands and feet away from rotating parts.
Be aware that they run for 5 sec. after the machine has been turned off.
| Keep word area free of other people.
| Be aware of the knives when using the lawn mover.
| Keep the power cord away from the working area in front of the machine.
| Use ear protection and safety classes during use.
Identification of parts
Illustration 1:
A. Mower and upper handle
B. Lower handle
C. Upper handle
D. Grass collection box
E. Mounting bracket (x2)
F. Cable strain relief
G. Cable clip (x2)
H. Screw with circular washer and nut with quick- release handle (x2)
I. Screw with rectangular washer and quick-release handle (x2)
Illustration 2:
- Switch box with appliance inlet
- Quick release lock
- Rear flap
- Handle
- Switch bar
- Upper handle
- Cord strain relief
- Lower handle
- Grass bag
- Height adjustment handle
- Deck
- Mulching plug
Assembly
Illustration 3:
Slide the cord strain relief (F) over the lower handle’s tube (B)
Illustration 4:
Insert each end of the lower handle (B) into a mounting bracket (E), making
sure that the cogs point inwards.
Slide the mounting bracket over their counterparts on the mower. Choose one of
three positions for small, medium or tall users. Use the screws with
rectangular washer [I] to fix the lower handle in place. Move the cable strain
relief (F) to the middle of the lower handle’s horizontal part (B). For easy
folding, guide the cable between motor and switch below (not above) the lower
handle’s horizontal part [B]. Clamp the upper handle (C) to the lower handle
and fix it using the screws with circular washer (H). Insert the screw from
the inside and note the order: Handle, Washer, nut with quick-release handle.
You can rotate release lock to adjust the tightness. Fit the handle to the
machine body as shown in the pictures. Lower handlebar should be fixed to the
brackets on the machine. The plastic cover is fitted outside. Add the washer
and then the handle-lock bolt.
The handle-lock kan be folded in, but be careful not to overtight it before
pressing it in. After pressed into position, it is recommende to tight the
bolt further by turning it around in closes position.
Illustration 5:
Attach the cable to the handle with the provided cable clips (G)
Illustration 6:
Slide the plastic profiles over the metal frame. Make sure the profiles
completely enclose the frame, lest they slide off during use.
Illustration 7:
- Raise up the rear flap.
- Hang the collection bag on the hooks
Specifications
Model | Smart 3700 | Smart 4400 |
---|---|---|
Voltage | 230-240V | 230-240V |
Effect | 1600 Watt | 1800 Watt |
Cutting width | 37 cm | 44 cm |
Collector box | 45 L. | 55 L. |
Height adjustment | 25-75 mm | 20-75 mm |
Weight | 13 kg | 16,5 kg |
Warranty terms and conditions
The warranty period is 2 years for private end users in EU countries.
Products sold for commercial use, only have a warranty period of 1 year.
The warranty covers material and/or fabrication faults.
Restrictions and requirements
Normal wear and replacement of wearing parts are NOT covered by the warranty.
Wearing parts, which are NOT covered for more than 12 months:
- Blades
- Cables
- Belts
- Fuses
- Switches
If you start the engine without adding oil, it will be damaged and cannot be
repaired and therefore not covered by the warranty.
The warranty does NOT cover damages/faults caused by:
- Lack of service and maintenance
- Structural changes
- Exposure to unusual external conditions
- Damages to the bodywork, deck, handles, panels etc.
- If the machine has been improperly used or overloaded
- Use of unoriginal spare parts.
- Other conditions where Texas cannot be held responsible.
Whether a case is a warranty claim or not is determined in each case by an
authorized service center.
Your receipt is your warranty note, why it should always be kept safe.
REMEMBER: The purchase of spare parts as well as any request for warranty
repair, art. number (e.g. 90063XXX), year and serial number should always be
informed. It can be found on the CE-label placed on the deck.
EC Declaration of conformity
Manufacturer
Texas Andreas Petersen A/S
Hereby certifies that the following
Lawn mower electric
Smart 3700 – Smart 4400
Is in compliance with following directives
2006/42/EC – 2014/30/EU – 2000/14/EC amended by 2005/85/EC Conforms with the
following standards
EN 60335-1: 2012+A11+A13, EN 60335-2-77: 2010, EN 62233: 2008,
EN IEC 55014-1: 2021, EN IEC 55014-2: 2021,
EN 61000-3-2: 2014, EN 61000-3-3: 2013
Serial no. (Smart 3700): 2401610001 – 2612619999
Serial no. (Smart 4400): 2401620001 – 2612629999
Smart 3700:
Left handle: a h,w : 1.32 m/s²/LpA: 85 dB(A)
Right handle: ah,W: 1.13 m/s² (K = 1.5 m/s²)/Lwa: 96 db(A)
Smart 4400:
Left handle: a : 2.51 m/s²/LpA : 89 dB(A)
Right handle: ah,W : 1.91 m/s²(K = 1.5 m/s²)
Texas Andreas Petersen A/S Knullen 22 5260 Odense S, Denmark
20.09.2023
Johnny Lolk
Managing Director
Responsible person for documentation
Johnny Lolk
Texas A/S – Knullen 22
DK-5260 Odense S
Denmark Tel. +45 6395 5555
www.texas.dk
post@texas.dk
Version 24.1
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>