TEXAS GSX2000 Battery Charger User Manual

TEXAS GSX2000 Battery Charger

Specifications

• Brand: GSX2000
• Manufacturer: Texas A/S
• Country of Origin: Denmark
• Battery and Charger not included for solo machines
• Version: 24.1

Product Usage Instructions

1. Safety
   

2. Before operating the machine, read the user manual carefully to understand all safety instructions.

3. Always wear work gloves, safety shoes/boots, and safety trousers with leg protection.

4. Avoid placing hands/fingers near the cutting area during operations.

5. Avoid exposing the equipment to extreme heat, fire, rain, or water. Store indoors and maintain below 45 degrees C.

6. Identification of Machine and Parts
   Remove all packaging and ensure all parts are undamaged.

7. Unpacking and Assembly
   Check that all parts are included and assemble the machine as per the user manual.

8. Battery Information

9. The battery capacity is not fully charged upon delivery. The battery has an energy indicator at the end.

10. To check battery status, press the button: LED 1 blinking – Fully charged (75-100%), 50%-75%, 25%-50%, 0%-25%, recharge when empty.

11. Full battery charging times: approximately 60 min for 2.0 Ah, 120 min for 4.0 Ah, and 150 min for 5.0 Ah batteries.

12. Maintenance
    Regularly maintain the equipment as per the maintenance guidelines provided in the user manual to ensure optimal performance.

13. Spare Parts
    For spare part drawings and purchases, visit www.texas.dk or contact your dealer with the specific part numbers.

FAQ

• Q: Can I use any brand of battery and charger with the GSX2000?
  A: No, it is recommended to use the compatible battery and charger specified for the GSX2000 to ensure proper functioning.

• Q: How should I store the GSX2000 during winter months?
  A: Store the equipment indoors in a dry place away from extreme temperatures to prevent damage.

• Q: What should I do if I encounter an issue with the battery indicator?
  A: If you face any problems with the battery indicator, refer to the user manual troubleshooting section or contact customer support for assistance.

User manual NOTE!
BATTERY AND CHARGER ARE NOT INCLUDED FOR SOLO MACHINES

Texas A/S – Knullen 22 – DK-5260 Odense S – Denmark Version 24.1
Tel. +45 6395 5555 – www.texas.dk – post@texas.dk

Warning symbols

| Warning:
Safety information about hazards that can result in personal injury
---|---
| Please read the user manual carefully before operating the machine.
| Use work gloves.
| Never place hands/fingers near the cutting area of the electric pruner during operations.
| Wear safety shoes/boots and safety trousers with leg protection.
| Do not expose the equipment to extreme heat or fire
| Do not expose the equipment to rain/water and store it indoor
| Do not expose to temperatures above 45 degrees C.
| Must be recycled
****| Waste electrical products must not be disposed of with the household waste. This tool should be taken to your local recycling center for safe treatment.

Spare parts

• Spare part drawings for the specific product can be found on our website www.texas.dk If you find the part numbers yourself, this will facilitate more rapid service.
• For purchase of spare parts, please contact your dealer.

Safety

How to read the manual

• Please read this instruction manual carefully, especially the safety warnings marked with the symbol:
• When using the product, the safety instructions must be closely followed. Read this manual carefully before starting the machine. Make sure that you know how to stop and switch off the engine in case of accident. All instructions regarding safety and maintenance of the machine are for your own safety.
• The warnings, precautions and instructions given in this manual, cannot cover all situations that the product can be placed in. The user must therefore present common sense and caution when using the product.

Safety in the work area

• Only use the product in clean and well lit areas
• Do not use the product in areas with explosive danger or where there is flammable fluids, gas or dust present.
• The person that uses the machine is responsible to other persons in the work area. Never use the machine when others, especially children or animals are near.
• This tool is an electric product. It is therefore important, that it never comes in contact with water or is used in wet surroundings.

Use and maintenance of the product

• This tool must not be used for other work than as described in this manual.
• Only use original spare parts. Mounting of non-approved parts may lead to increased risk and are therefore not legal. Any liability is renounced for accidents or other damage that has happened due to the use of unauthorised parts.
• Before using the machine, the dealer or other qualified person should instruct you in the use of the machine.
• Minors may not work the machine.
• The machine may only be lent to people who know how to work the machine. This manual should follow the machine under all circumstances.
• This tool may only be used by persons who are rested, well and fit. If the work is tiring, frequent brakes should be made. Do not use the machine under influence of alcohol.
• Always check before start, that all bolts and nuts are tigthened.
• Always wear eye protection when using the machine.
• Keep children and other persons at a distance of at least 5 metres from the work area.
• The battery should always be removed when:
  • maintenance is made.
  • the machine is left unattended
• During transport, the main switch must be switched off.

Identification of the machine and components

See Fig. 1

1. Electric pruning shear
2. Tool kit

See Fig. 2

1. Blade (moveable)
2. Blade (fixed)
3. Gear
4. Trigger switch
5. Power switch
6. Battery*
7. Release button
8. Display screen

*Battery/charger are not included for solo machines

Unpacking and assembly

1. Unpack all parts and lay them on a flat, stable surface.
2. Remove all packing materials and shipping devices, if applicable.
3. Make sure the delivery contents are complete and free of any damage. If you find that parts are missing or show damage do not use the product but contact your dealer. Using an incomplete or damaged product represents a hazard to people and property.
4. Ensure that you have all the accessories and tools needed for assembly and operation.
5. Plug in the battery, by pushing it in until you hear a click (Fig. 3).
6. Remove the battery by push down the battery lock buttons and pulling it out.

NOTE: Always remove the battery before assembly and maintenance.

Battery

• Not included for solo machines*
• Warning: Do not try to disassemble, short circuit or put it to extreme heat or fire, as it can cause serious inquiry and permanent damage to the battery!
• Battery pack is not fully charged when delivered.

Charging

• Only use the original charger with art. no. 90063242 or 90063241.
• Before the battery is being used the first time, it is recommended to fully charge it first.

Charge the battery.

• Note: The indicator lights is only indicative indications, and is not accurate power indications.
• Important: To protect the battery from total discharge, the machine will stop, when the battery is nearly empty.
• The machine must not be started up again after automatic shutdown, as it can damage the battery. The battery must be recharges before the work can continue.

Charger

• A full charge of battery takes around 60 min for 2.0 Ah, 120 min for 4.0 Ah and 150 min for 5.0 Ah battery.
  • Only use the original charger*
  • Do not try to charge other type of batteries in the charger, other than the original batteries with art. no. 90063245 (2.0 Ah), 90063246 (4.0 Ah) or 90063247 (5.0 Ah).
  • Keep the charger in a dry and warm environment (10-25 degrees C) and only use it indoor. It should be connected to a normal 230V AC socket.
  • Before the battery is being used the first time, it is recommended to charge it fully.
  • The surface of the battery can become warm during charging. This is normal.
  • Do not cover battery or charger during charging. Allow free ventilation of air.
• Insert the battery into the slots of the charger and slide it into place until it locks.
• There are 4 lights on the charger indicating the status and state of charge of the battery.
• Important: The charger will stop, when the battery is full. However, it is not recommended to leave the battery in charger for more than 24 hours.
• It is recommended to drain the battery completely and fully charge it whenever possible, as it can increase the health of the battery. But partial charge will not damage the battery.
• To remove the battery from the charger, hold the button down and pull the battery out.
• Before winter storage, the battery should be fully charged and kept warm at 10-20 degrees C. Charge it every 3 months. Make sure to keep ventilation holes clean and free from dirt.
• Store the charger indoor between 5-25 degrees C.

Use

Never place hands/fingers near the cutting area of the electric pruner during operations. Pay high attention to where you place your fingers, as the blade kan cause big personal injury.

• Before use, make sure that the battery is fitted properly with the battery lock in place.
• Press the power button (5) to turn on the pruner.
• Double click the trigger, the pruner blades will automatically open.
• To use the pruner, activate the trigger switch (4) and release it when the branch is cut.
• Blade closing: continue to press the trigger (4), a buzz means the blade will stay closed.
• Before operation: to see if the pruner performances well, please press the trigger to close and release the trigger to open the blades without cutting anything. Repeat this for a few times.
• Press the power button (5) for some seconds to turn off the pruner.

Display screen (Fig. 6)
The display screen (8) shows following status:

• Remaining capacity
• Shearing times
• Opening size

Touch sensor

• For extra safety, the pruner is equipped with a touch sensor on the blade, which detects if there is contact with fingers/hands by using a weak current.
• After the scissors are turned on, the anti-cutting hand function is enabled by default. When the other hand of the operator touches the blade, a current loop is formed, the buzzer continuously emits a beep, and the scissors stop working
• Long press the trigger for 5 seconds and hear the buzzer sound twice, the anti-cutting hand function is turned off, the scissors can continue to work, but the anti-cutting hand function has been lost
• After the anti-cutting hand function is turned off, press and hold the trigger again and hear the buzzer twice, and the anti-cutting hand function can be turned on again
• After the scissors are turned off and turned on again, the anti-cutting function is turned on by default
• Note: All electronic safety may fail, so NEVER place your fingers between the blades. It can cause great personal injury (clipped finger).
• For safety reason, it is recommended always to keep the touch sensor activated!

Never place hands/fingers near the cutting area Never place hands/fingers near the cutting area of the electric pruner during operations. Pay high attention to where you place your fingers, as the blade kan cause big personal injury.

Clothing
When using the machine, wear tight-fitting work clothes, strong working gloves, hearing protectors, eye protection, safety boots with non-skid soles and protective trousers.

Tips and advices

Follow these advices to get a better working result:

1. A fully charged battery have more power than a half-empty battery when it comes to cutting big branches.
2. Keep the pruner in a perpendicular position from the branch to getter a cleaner cut. If the pruner is tilted a little bit to the side, it will be more difficult to cut properly.
3. Be careful not to hold the fingers, where the pruner is cutting. Keep good distance between hands and the blade of the pruner.

Maintenance

Before any service and maintenance is done, the power must be disconnected, it means the battery removed from the tool.

• Remove the battery before you clean and store the machine.
• For obtaining the best cutting results the knives must be cleaned and oiled regularly. Remove dirt with a soft brush and oil lightly.
• Pour some drops of oil in the lubrication hole on the blade (Fig. 4) 1-2 times per year and before winter storage. Use the included oil.
• Clean the housing and other parts with a mild cleanser and a moist cloth. Never use aggressive cleansers or solvents.
• Prevent water from getting into the machine.

Replacement of blade. See Fig. 5

• The moveable blade (1) can be replaced. Loosen and remove the nut with the included wrench. Remove the the bolt and the blade.
• To fit a new blade, insert the blade in a 45o degree angle, until the teeth match the gearbox. Adjust the angle of blade so both blade holes are aligned. Mount the bolt, washer and nut and tighten again.
• Lubricate the blade with oil.

Specifications

Warranty terms and conditions

• The warranty period is 2 years for private end users in EU countries. Products sold for commercial use, only have a warranty period of 1 year.
• The warranty covers material and/or fabrication faults.

Restrictions and requirements
Normal wear and replacement of wearing parts are NOT covered by the warranty.

• Wearing parts, which are NOT covered for more than 12 months:
  • Blade
  • Blade tip protector
  • Battery: If the battery is not stored correct (frost-free and recharged every 3 months), the durability is only guaranteed for 6 months.
• The warranty does NOT cover damages/faults caused by:
  • Lack of service and maintenance
  • Structural changes
  • Exposure to unusual external conditions
  • If the machine has been improperly used or overloaded
  • Wrong use of oil, gasoline or other liquid types, which are not recommended in this user manual
  • Use of unoriginal spare parts.
  • Other conditions where Texas cannot be held responsible.

Whether a case is a warranty claim or not is determined in each case by an authorized service center. Your receipt is your warranty note, why it should always be kept safe.
REMEMBER: The purchase of spare parts as well as any request for warranty repair, art. number (e.g. 90063XXX), year and serial number should always be informed.

• We reserve the right to change the conditions and accept no liability for any misprints.

EC Declaration of conformity

• Manufacturer
  Texas Andreas Petersen A/S

• Hereby certifies that the following
  Battery pruner GSX2000

• Is in compliance with the specifications of the machine directive and subsequent modifications
  2006/42/EC – 2014/30/EU

• Conforms with the following standards
  EN 62841-1:2015+A11:2022, IEC 62841-1:2014, EN ISO 12100:2010 EN IEC 55014-1:2021, EN IEC 55014-2:2021

• LpA: 68.7 dB Vibrations Ah:

• LwA 83 dB 1.14 m/s2 (K=1.5 m/s2)

• Responsible for documentation Johnny Lolk

References

• Salg af havemaskiner - Texas A/S
• Salg af havemaskiner - Texas A/S

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>