TEXAS XM 461 TR Gasoline Lawn Mowers User Manual

TEXAS XM 461 TR Gasoline Lawn Mowers

Product Information

• Model: XM 461 TR/W, XM 510 TR/W, XM 512 TR/W,XM 514 TR/W, XM 515 TR/WE, XM 516 TR/WE
• Manufacturer: Texas A/S
• Engine Oil: SAE-30

Specifications

• Actual model may vary from the illustration shown
• Version: 24.1
• Country of Origin: Denmark
• Contact: Tel. +45 6395 5555, www.texas.dk, post@texas.dk

Product Usage Instructions

Engine Oil Filling
Before starting the machine, remember to fill the engine with SAE-30 oil. Follow the manufacturer’s guidelines on the correct oil quantity and procedure.

Safety Precautions
Always wear eye and ear protection before operating the machine.
Keep a safe distance from rotating blades and sharp objects to prevent personal injury.

Operating the Machine
Start the engine according to the user manual instructions. Keep hands and feet away from the cutting deck while the machine is in operation. Pay attention to any warning symbols and follow safety guidelines.

FAQ (Frequently Asked Questions)

Q: What type of oil should I use for the engine?
A: It is recommended to use SAE-30 engine oil for this product. Refer to the user manual for specific details on oil specifications.

Q: How do I clean the work area around the machine?
A: Before cleaning the work area, make sure to stop the engine. Use appropriate tools to remove debris and maintain a safe distance from the cutting deck.

Safety

• Do not put hands or feet near or under rotating parts.
• Read this manual carefully. Make sure that you are familiar with the different controls, settings and handles of the equipment.
• Know how to stop the unit and ensure that you are familiar with emergency stop.
• Never allow children or people unfamiliar with these instructions to use the machine. Note, that local regulations can restrict the age of the operator.
• If you feel unwell, tired or have consumed alcohol or drugs, do not operate the machine.
• Always inspect the machine before usage Ensure that no parts are worn or damaged.
• Replace worn out or damaged elements and bolts in sets to preserve balance.
• The operator of the machine is responsible for people’s safety.
• Never use the machine near children or animals. The operator of the machine is held liable for any accidents or hazards to other people and their property.
• Thoroughly inspect the area, where the equipment is to be used, if necessary remove any foreign objects.
• Do not refuel gasoline indoors or while the engine is running.
• Spilled gasoline is extremely flammable, never refuel while the engine is still hot.
• Wipe off any spilled gasoline before starting the engine. Spilled gasoline on a hot engine may cause a fire or explosion!
• Boots with non-slip soles with steel jacket is required. Avoid loose-fitting clothes.

Operation

• After striking a foreign object, stop the engine immediately, remove the spark plug cap and inspect the machine thoroughly for damage. Repair the damage before continuing.
• If the machine should start to vibrate abnormally, stop the engine and check immediately for the cause. Vibration is generally a warning of damage.
• Always turn off the engine and ensure that all moving parts have come to a complete stop before making any repairs, adjustments, or inspections.
• Exercise extreme caution when operating on slopes.
• Never operate the machine at a fast pace.
• Do not overload machine capacity by attempting to push at too fast a rate.
• Do not carry passengers.
• Never allow any bystanders in front of unit.
• Only operate the machine at daylight or in fully illuminated areas.
• Ensure a stable foothold and always keep a firm hold on the handles. Always walk, never run.
• Do not operate the machine when barefoot or wearing sandals.
• Exercise extreme caution when changing direction on slopes
• Never attempt to make any adjustments, while the engine is running.
• Use extreme caution when reversing or pulling the machine backwards
• Never operate the engine indoor or in areas with low ventilation. The exhaustion from the engine contains carbon monoxide. Failure to observe could result in permanent injury or death.
• Due to vibrations from the handle, long time use can result in white fingers.
• If fatigue is felt in arms, hands or fingers – or visible signs of white fingers is appearing, the work should be stopped immediately and a sufficient time of break should be taken for recovery. To avoid white fingers, each user should operate the machine for no more than 1.5 hours per day.

Gasoline safety

• Use extreme care in handling gasoline.
• Gasoline is extremely flammable and the fumes are explosive.Serious personal injury can occur, when gasoline is spilled on yourself or your clothes. Rinse your skin and change clothes immediately! Use only an approved gasoline container. Do not use soft drink bottle or similar!
• Extinguish all cigarettes, cigars, pipes and other sources of ignition.
• Never refuel your machine indoors.
• Let the engine cool down before refilling
• Never fill the fuel tank to more than 2.5 cm below filler in order to provide space for fuel to expansion. After refueling, ensure that the cap tighten securely.
• Never use the lock-function on the gasoline gun, when refueling.
• Do not smoke while refueling.
• Never refuel gasoline inside a building or where gasoline fumes may get in contact with an ignition source.
• Keep gasoline and engine away from appliance, pilot lights, barbecues, electric appliances, power tools, etc.

Maintenance and storage

• The engine shall be stopped when carrying out maintenance and cleaning operations, when changing tools and when being transported by means other than under its own power.
• Check regularly that all bolts and nuts are tightened. Retighten if necessary.
• The engine must be completely cooled before storing indoors or covered.
• If the machine unused for a period of time, please refer to the instructions in this manual.
• Maintain or replace safety and instruction labels, as necessary.
• Only use orginal spare parts or accessories. If not orginal parts or accessories is used, the liablility is no longer applied.

Miscellaneous

• The motor is not pre-filled with oil.
• Always before start check the engine oil level. Factory-fitted control devices, such as the handle-mounted clutch cable, must not be removed or exposed.
• Only drain the fuel tank outdoors.
• Gasoline is extremely flammable and the fumes are explosive. Ensure that the machine is properly secured when transported on a flatbed etc.

Waste electrical products must not be disposed of with the household waste. This tool should be taken to your local recycling centre for safe treatment.

The lawnmower is manufactured according to the latest safety requirements. These include a blade brake that stops the motor and blade in 3 seconds when the blade brake. Every precaution is only effective when it is followed exactly. Use the following description when you mount your lawnmower.

Identification of the parts

See Illustration ID

Notice: the illustrations may vary from your present model

• A. Handlebar for drive

• B. Handlebar for engine brake

• C. Recoil starter

• D. Wing nut

• E. Rear discharge guard with spacer blocks *

• F. Water nozzle *

• G. Grass collector

• H. Gasoline filling cap

• I. Air Filter

• J. Exhaust

• K. Spark plug

• L. Oil cap

• M. Mulching plug

• N. Throttle lever – Speed lever *

• O. Choke*

• P. Height adjustment*

• Q. Side discharge guard*

• R. Primer*

• S. Breastplate*

• T. Electric starter*

• may vary from your actual model.

Mounting

Unpacking: Illustration M1

Remove the mower from the box by pulling the machine out form the side. The box contains:

1. 1 pcs mower
2. 4 pcs wing nut set consisting of wing nuts, bolts and washers. (See ID; D)
3. 2 pcs spacer blocks (See ID; E)

Warning: Ensure that cables are not pinched.

Handlebar and height adjustment:
Illustration M2 The handlebars are height adjustable. This means that they can be adjusted so that it best fits you. Before you install the handlebar, it may be a good idea to have decided which height is best for you.

1. Set the lower handlebar tube to the working height that suits you. “H” is high position and the “L” is low position.
2. Attach the wing nut from the inside of the side bracket and into the lower handlebar.
3. Attach the upper handlebar on the lower. Fasten with wing nut from the inside of the handlebar.
4. Customize cable and secure with cable clamps

Mounting the engine brake cable: Illustration M3

1. Gently push the top handlebar ID:B forward
2. Insert the engine brake cable from the outside, into the hole in the bracket on handlebar ID:B and lock.

Mounting the drive cable: Illustration M3

1. Gently push the lower handlebar ID:A downward
2. Insert the drive cable from the inside, into the hole in the bracket on handlebar ID:A and lock.

Mounting the recoil-starter: Illustration M4

1. Pull the engine brake handlebar and hold, in order to release the starter cord on the engine.
2. Pull gently the starter cord from the engine (Engine brake handlebar MUST be hold)
3. Attach the starter grip on the rack of handlebar.
4. Release the engine brake handlebar and the starter grip.

**Mounting the breastplate: illustration M5***

1. For models with breastplate with cup holder follow illustration M5-1
2. For models with breastplate follow illustration M5-2

Note: Not all models do have breastplate

Mounting the grass collector: Illustration M6

1. Click the frame to the grass collector.
   The grass collector comes with a handy indicator showing whether the box is full of grass and needs emptying.

Rear discharge guard: Illustration M7-1
If you want to mow without grass collector it is important to attach the two spacer blocks.

1. Insert the 2 blocks (ID:E) under the rear discharge
2. guard.

Note: The spacer blocks are for rear ejection only! Otherwise they should be removed.

Warning: If the two blocks are not mounted. The mower will have difficulties to dispose the grass.

Mulching plug: Illustration M7-2

1. Insert the mulching plug and remove side discharge guard, if you want to mow with mulching functionality.
   NB Don’t use the grass collector

Important: Remember to remove the mulching plug, when using the grass collector.

**Side discharge guard: Illustration M7-3***

1. Lift the side guard and insert side discharge guard. Then insert the mulching plug in rear discharger to mow with side discharge function. NB Don’t use the grass collector

Note: Not all models do have side discharge guard

Cable Adjustment

Before the machine is being used, the cable adjustment should always be checked.
The cables can be checked by activating the handles fully and check if the cable is tight. If not, it must be tightened. If the handle cannot easily be fully activated, the cable should be loosened.
After first season, it must be expected that the cables need to be adjusted for optimal activation, as cables can stretch when used.

The following cables may be necessary to readjust: Illustration A1

1. Cable for drive
2. Cable for engine brake
3. Cable for throttle cable

Note: The choke cable cannot be adjusted!
Adjusting the drive cable: Illustration A1-1*
If you experience slack in the drive cable, this can be solved simply by tighten or loosen the bolt on the cable.

1. Tighten turning clockwise – loosen the cable.
2. Tighten turning anti clockwise – tighten the cable.

Cable can only be adjusted on some models.
Adjusting the engine brake cable: Illustration A1-2 If you experience slack in engine brake cable, this can be solved simply by tighten or loosen the bolt on the engine block.
Adjusting the throttle cable: Illustration A1-3*
If you experience slack in throttle cable, this can be solved simply by tighten or loosen the bolt on the engine block.

Not all models have throttle cable.

Battery (Electric starter)

Charge the battery before use
Before the electric start function is used, the battery must be charged for 5 hours. Put the charger plug into the hole in the battery and connect the charger to a power supply. See illustration. A4

Charging during the season
The battery is not charged during use, so it will likely be necessary to charge the battery a couple of times during the season – depending if the number of start/stops of the engine. Put it for charging for around 5 hours.

Storage of battery
The battery must always be stored dry and warm during the winter. Never expose it for low temperatures. Charge the battery completely before storing and then place the lawn mower in a place where it is not exposed to frost. Alternatively cover the battery with a thick carpet or similar, If the mower is in a shed/garage where there may be cold.
Charge the battery 1-2 times during the winter (at least every 3rd month) to make sure the battery keeps it full capacity.

Incorrect storage can damage the battery and is not covered by warranty.

Note: Not all models have electric starter

Operation

Always check and refill oil before the start! Read and apply the instructions given in the enclosed start guide!
The oil level should always be between min. and max on the dipstick. Fill with SAE-30 oil. There should be total 0.6 liter oil in the engine. Use only unleaded E5 fuel to the engine. Never overfill the tank.

Cutting height adjustment : Illustration F1
(the illustrations may vary from your actual model) The mower has 6 different heights. The cutting height ranges from 28 mm to 75 mm

Start: Never start the mower directly on long grass.

Recoil with primer: Illustration F2

1. Push the primer several times, first time push 1-3 times, if necessary, supplement with up to 3-5 times.
   Note: It is not possible to drown engine

2. Hold the handlebar for the engine brake; this will release the engine brake.

3. Pull the recoil starter gently until you feel resistance in the rope, then pull quickly and energetic. Do not at any time let go of the recoil starter but slide it gently into starting position.

4. Hold the bar for self-propelled in order to start mowing

Recoil with choke, throttle lever: Illustration F3-A

1. By cold engine set the choke lever on ”Choke”. By warm engine set the choke lever on ”Run”.
2. Move the throttle lever to full “Rabbit” (A)
3. Hold the handlebar for the engine brake; this will release the engine brake.
4. Pull the recoil starter gently until you feel resistance in the rope, then pull quickly and energetic. Do not at any time let go of the recoil starter but slide it gently into starting position.
5. Adjust the throttle lever if necessary and return the choke lever in the ”Run” position (only cold engine).
6. Hold the bar for self-propelled in order to start mowing.

Electrical starter: Illustration F3-B

To avoid unintentionally starting the machine, the start button should be removed from the machine and stored safely when the machine is not in use.

1. By cold engine set the choke lever on ”Choke”. By warm engine set the choke lever on ”Run”.
2. Move the throttle lever to full “Rabbit” (A)
3. Hold the handlebar for the engine brake; this will release the engine brake.
4. When starting the machine, insert the start button in the ignition lock below the handlebar and push in.
5. Hold the button (B) in until the engine starts and then release.
6. Adjust the throttle lever if necessary and return the choke lever in the ”run” position (only cold engine).
7. Hold the bar for self-propelled in order to start mowing.

**Recoil with choke, speed lever illustration F3-C***

1. By cold engine set the choke lever on ”Choke”. By warm engine set the choke lever on ”Run”.
2. Hold the handlebar for the engine brake; this will release the engine brake.
3. Pull the recoil starter gently until you feel resistance in the rope, then pull quickly and energetic. Do not at any time let go of the recoil starter but slide it gently into starting position.
4. Return the choke lever in the ”Run” position (only cold engine) .
5. Set speed lever in gear from 1 to 4 (C)
6. Hold the bar for self-propelled in order to start mowing.

Note: Not all models are equipped with choke lever.

Note: As long as operating the mower, the bar forengine brake must be engaged.
Throttle lever*
Engine speed can be adjusted while driving. Turn gas handle to adjust rpm. (ID: M) It is recommended to run at full throttle for best cutting results.

Note: Not all models have throttle control

**Regulation of speed***
Speed can be adjusted from 2.7 – 5.0 km/h while driving. Activate the right handle on the dashboard and set in one of the 4 different speeds. When driving in one the two lowest speeds the pace difference will not vary significantly.
Change the speed only while the machine is operating with the self-propelled function engaged.
This ensures a minimum of wear on the drive belt and ensures an easy speed change.
If the drive speed is changed when the machine is not moving, there is a risk that the belt will fall off as soon as the machine starts to move. In addition, there is a risk that the cable and the belt may become damaged.

Note: Not all models have speed lever

Stop: Illustration F4

1. Release the engine brake and self-propelled bar to turn off the mower and the engine
   Note: The blades will still rotate at up to 3 seconds after stopping.

Water nozzle

The left side of the mower deck is fitted with a water nozzle for washing the deck. (See Illustration ID-F)

• When using the water nozzle, the machine must be in the lowest height position and placed on the lawn. This ensures that the water remains under the deck during cleaning.
• Attach a hose to the nozzle.
• Turn on the water and start the engine.
• The rotations of the blades will ensure that the water will clean the underside of the deck.

If above instruction is not followed, water may splash back on the gearbox and clutch cable, which increases the risk of corrosion and damage to both parts. This will not be covered by the warranty!

Note: For best result clean the deck with the water nozzle function right after each mowing. If the grass dries out, this function will not work optimally.

• Note: Not all models have water nozzle

Oil change

Oil should be changed for the first time after 5 hours, then at least 1 time per year.

You will need an oil extractor kit. Art. no. 40-11336 Oil and oil extractor kit is not included

Use an extractor kit and do as follows:

1. Turn on the engine and let it run for 5 min or until the engine is hot. A hot engine liquefies the oil which makes it easier to drain.
2. Suck the oil up through the oil filler hole using the syringe that came with the oil extractor kit. Use the hose to reach the sump.
3. Transfer the used oil into a empty container.
4. Fill the engine with SAE-30 oil.
5. Check the oil level using the dipstick. (Min / Max)

Remember to dispose the used oil so that it does no harm to nature. Use your local recycling station.

Air Filter

The air filter should be inspected and cleaned regularly. If the filter has not been cleaned for a long time, the engine’s power will drop.

See Illustration A2

1. Clean around the air filter before removing the cap.
2. Push the two flaps down and gently pull the cover
3. Carefully remove the paper filter and inspect it. Brush it with a soft brush. If it is very dirty, replace it. Be careful that no dirt gets into the inlet.
4. Wash the black foam element in the right side in warm water and soap.
5. Press the water out of the foam element and let it dry. Put a few drops of SAE-30 oil on the filter to moisten it lightly. Carefully squeeze any surplus oil out of the foam element and reattach.
6. Please note that all parts are assembled correctly and properly closed, as shown in the picture.

Blade

Inspection of the blade

• Tilt the mower with the front upwards.
• Inspect blade for damage, cracks or excessive rust or corrosion.
• Check that the blade bolt is tightened.

Note: A dull blade can be sharpened! But a blade that is worn, bent, cracked or otherwise damaged must be replaced.

Removing the blade: See illustration A3
If you remove the blade to sharpen or replace it, you must use a torque wrench and some heavy gloves to protect your hands.

1. Loosen the blade bolt. Use a piece of wood to prevent the blade from turning around.
2. Remove the bolt, washer, blade and blade holder in that order
3. Sharpen or replace the blade.
4. Insert the blade holder, blade, washer and bolt in that order.
5. Tighten the blade bolt with 50 Nm. Use a piece of wood to prevent the blade from turning around.

Warning: A blade must be sharpened so it is in 100 % balance, otherwise it may cause vibrations that could damage the engine. Damage to engine due to faulty sharpening is not covered by warranty. We therefore recommend letting a service center sharpen the blade.

Spark plug

1. Remove the spark plug.
2. Brush off dirt from the spark plug.
3. Use a spark plug wrench to loosen the spark plug.
4. Check the insulation is intact.
5. Clean the spark plug with a wire brush.
6. Measure the electrode, taking care not to damage the electrode.
7. The distance should be: 0.7 to 0.8 mm
8. If the spark plug is undamaged refit or replace. Art. no. 40-11294
9. Reattach the spark plug.

Storage and maintenance

Maintain your lawnmower: Check all bolts, screws, nuts and deck. Dismount the blade and the belt plastic cover for regular cleaning. Always make sure that the blade is sharp. It’s a good idea to take your lawn mower to an annual service check with your authorized service dealer. See your nearest service center at www.texas.dk.

Storage: After use the lawnmower kept in a dry and clean room. Clean the machine after every use. Grass and dirt must be removed from the underside of the deck. By tipping the mower (for cleaning) is recommended to tilt the front up (max. 45 degrees). If you tilt it sideways, the carburetor and air filter always face upwards, since oil may run out and destroy the engine. Be aware that removing the spark plug before the mower maintenance.

Winter storage : Empty the fuel tank and let the engine run until the gasoline in the carburetor is used up. Spark plug removed. Remove the spark plug and add a teaspoon of oil (engine oil) in the hole. Pull the starter to distribute oil. Mount the spark plug, but not the spark plug cap. Change oil as described in the section above. Spray silicone lubrication into the cables and move them.
Finally, clean the mower thoroughly. Dip a cloth in oil and luricate metal parts to prevent rust.

Cleaning and lubricating of rachet wheels:
See illustration A5
Cleaning and lubricating of all rachet wheels should be done minimum once per year to ensure longer durability. If no maintenance is performed, the warranty will not cover these parts.

Follow below procedure (for both rear wheels)*:

1. Remove the wheel covers
2. Unscrew the nut with a 13 mm wrench
3. Pull of the washer and the wheel
4. Remove the retainer ring with a suitable tool and the rachet wheel
5. Clean shaft/rachet wheel for old grease and dirt.
6. Lubricate with suitable grease (e.g. EP-0)
7. Mount the wheel and wheel cover again

• Only apply for self-propelled models.

Warranty terms and conditions

The warranty period is 2 years for private end users in EU countries.
Products sold for commercial use, only have a warranty period of 1 year.
The warranty covers material and/or fabrication faults.

Restrictions and requirements
Normal wear and replacement of wearing parts are NOT covered by the warranty.

Wearing parts, which are NOT covered for more than 12 months:

• Blades
• Cables
• Belts
• Fuses
• Switches
• Membranes/gaskets
• Spark plugs
• Engine liquids (oil, gasoline)
• Starter cords
• Filters
• Battery: If the battery is not stored correct (frost-free and recharged every 3 months), the durability is only guaranteed for 6 months.

If you start the engine without adding oil, it will be damaged and cannot be repaired and therefore not covered by the warranty.

The warranty does NOT cover damages/faults caused by:

• Lack of service and maintenance
• Structural changes
• Exposure to unusual external conditions
• Damages to the bodywork, deck, handles, panels etc.
• If the machine has been improperly used or overloaded
• Wrong use of oil, gasoline or other liquid types, which are not recommended in this user manual
• Bad or dirty gasoline, which results in contamination of the fuel system
• Use of unoriginal spare parts.
• Other conditions where Texas cannot be held responsible.

Whether a case is a warranty claim or not is determined in each case by an authorized service center.
Your receipt is your warranty note, why it should always be kept safe.

REMEMBER: The purchase of spare parts as well as any request for warranty repair, art. number (e.g. 900665XX), year and serial number should always be informed. It can be found on the CE-label located on the rearpart of the cutting deck behind the engine!

We reserve the right to change the conditions and accept no liability for any misprints.

Specification

Sound pressure level LpA

Measurement uncertainty

| 82.1 dB(A)

2.5 dB(A)

| 84.4 dB(A)

2.5 dB(A)

| 84.4 dB(A)

2.5 dB(A)

| 84.4 dB(A)

2.5 dB(A)

| 84.4 dB(A)

2.5 dB(A)

| 84.4 dB(A)

2.5 dB(A)

Sound power level LWA

Measurement uncertainty

| 93.61 dB(A)

1.40 dB(A)

| 95.38 dB(A)

0.85 dB(A)

| 95.38 dB(A)

0.85 dB(A)

| 95.38 dB(A)

0.85 dB(A)

| 95.38 dB(A)

0.85 dB(A)

| 95.38 dB(A)

0.85 dB(A)

Guaranteed sound power level| 96 dB(A)| 98 dB(A)| 98 dB(A)| 98 dB(A)| 98 dB(A)| 98 dB(A)
Engine
Model| TG470| TG570| TG570| TG570| TG570E| TG570E
Power| 139 cc| 173 cc| 173 cc| 173 cc| 173 cc| 173 cc

Troubleshooting

Difficult to start

Problem| Cause| Solution
Generally difficult to start| ·         Wrong starting procedure| · Follow the starting instructions in the manual precisely.
The start cable is very tight (will not start)| ·         The brake handle is not being activated

·         The machine is placed in high grass

| ·         Activate the brake handle and pull the start cord.

·         Move the machine away from the high grass and repeat the start procedure.

Set the height adjustment in the highest position, so that the blade is lifted free of the grass.

The machine will not start when the start cord is pulled or the electric start button is pushed (or the starter “clicks” when attempting an electric start)| ·         The brake handle is not being activated

·         The wires are not connected to battery The brake cable is incorrectly adjusted

·         The machine is standing in high grass

·         Engine brake cable is too loose

·         Engine is not primed before starting

·         The choke is not in the correct position

·         No more gasoline in fuel tank

·         The gasoline is more than 3 months old

| ·         Activate the engine brake handle and press the electric start button.

·         Check that the wires are connected from the battery to the motor and start button.

·         Adjust the engine brake cable, following the instructions in the manual.

·         Move the machine away from the high grass to start it. Tip the machine when starting.

Set the height adjustment in the highest position, so that the blade can run freely.

·         Tighten the engine brake cable by adjusting the bolt on engine

·         Push the primer 1-3 times before starting.

·         Move the choke lever to a different position.

·         Check and fill fuel tank with gasoline.

·         Empty the fuel tank and carburettor from old gasoline, and fill with new gasoline.

No ignition spark (cannot start)| ·         The spark plug cap is loose

·         The spark plug is damp or dirty

·         Incorrect gap between the spark plug and the electrode

·         The air filter is dirty or defective

| ·         Check that the cap is firmly attached to the spark plug.

·         Check that there is no dirt on the spark plug, following the instructions in the manual.

·         Check and adjust the spark plug gap, following the instructions in the manual. Alternatively, replace the spark plug.

·         Check the air filter for dirt and clean it, following the instructions in the manual.

The mower starts, but runs unevenly
Problem| Cause| Solution
Insufficient engine revolutions| ·         Lever is in the “Choke” position

·         The throttle lever is set for “Turtle “

| ·         Set the lever in the “Run” position.

·         Set the throttle lever for “Rabbit”.

The back wheels are not pulling, or only very little| ·         The clutch cable is too tight/too loose

·         The ratchets in the rear wheels are worn

| ·         Adjust the clutch cable, following the instructions in the manual.

·         Replace the ratchets.

The engine runs irregularly and/or its performance becomes poor as you are working| ·         The spark plug cap is loose

·         The spark plug is dirty

·         Incorrect gap between the spark plug and the electrode

·         The air filter is dirty or defective

·         Evaporation of fuel in the carburettor

·         Loose throttle cable

·         Dirt in the carburettor

| ·         Check that the cap is firmly attached to the spark plug.

·         Check that the spark plug is clean and not damaged, following the instructions in the manual.

·         Check and adjust the spark plug gap, following the instructions in the manual.

·         Check the air filter for dirt and clean it, following the instructions in the manual.

·         Wait a few minutes, and then try to start again.

·         Tighten the throttle cable, following the instructions in the manual.

·         Clean the carburettor.

The engine will not stop
Problem| Cause| Solution
The machine does not stop after 5 seconds| ·         The engine brake cable runs too tightly| ·         Check and adjust the engine brake cable, following the instructions in the manual.

Certificate of conformity

EN ISO 14982: 2009, EN ISO 5395-1: 2013, EN ISO 5395-2: 2013
Serial numbers: 2401320001 – 2612399999

Model
XM 461TR/W
XM 510TR/W, XM 512TR/W, XM 514TR/W XM 515 TR/WE, XM 516TR/WE

Guaranteed LwA 96 dB(A)
98 dB(A)
98 dB(A)

Texas Andreas Petersen A/S

Responsible for documentation
Knullen 22 • DK-5260 Odense S Johnny Lolk

23.10.2023
Johnny Lolk
Managing Director

References

• Salg af havemaskiner - Texas A/S

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>