LINDY 43095 USB 3.1 NVMe M.2 SSD Enclosure User Manual
- June 5, 2024
- LINDY
Table of Contents
LINDY 43095 USB 3.1 NVMe M.2 SSD Enclosure
Introduction
Thank you for purchasing the USB 3.1 to NVMe M.2 SSD Enclosure. This product has been designed to provide trouble free, reliable operation. It benefits from both a Lindy 2 year warranty and free lifetime technical support. To ensure correct use, please read this manual carefully and retain it for future reference.
Package Contents
- Enclosure for M.2 SSD
- USB 3.1 Gen 2 Type C to C cable, approx. 26cm
- Small screwdriver
- Screws & nut for enclosure and M.2 SSD
Specification
- USB 3.2 / 3.1 Gen 2 (10 Gbps) standard
- For PCIe/NVMe based M.2 SSDs with M key
- Supports 30mm (2230), 42mm (2242), 60mm (2260) and 80mm (2280) M.2 NGFF form factors with M key
- Chipset: ASM2362
- UASP & TRIM support
- Durable aluminum casing
- Plug and Play, USB Bus powered
- Operating temperature: -5°C – 45°C (23°F – 113°F)
- Storage temperature: -40 to 65°C (-40°F – 149°F)
- Humidity: 20 – 80 % RH (non-condensing)
Installation
Remove the two screws located on the side of the enclosure and slide out the internal drive tray. Install the nut in the correct hole – depending on the length of your M.2 SSD. The nut must be placed in the notch of the SSD before it can be inserted into the hole of the board. Then slide the connector of your M.2 SSD into the corresponding connector on the internal drive tray and tighten the screw. For 80mm SSDs the nut is already pre-installed, so that the SSD can simply be inserted. Slide the drive tray back into the enclosure, close it with the side plate and tighten it with two screws. Connect the included USB 3.1 Gen 2 Type C to C cable to your computer and to the USB 3.1 M.2 SSD Enclosure. The operating system will install necessary drivers automatically and the USB 3.1 Type C M.2 SSD Enclosure is now ready for use.
Radio Frequency Energy, Certifications
-
CE Certification
LINDY declares that this equipment complies with relevant European CE requirements. -
UKCA Certification
LINDY declares that this equipment complies with relevant UKCA requirements. -
FCC Warning
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. Operation is subject to the following two conditions:- This device may not cause harmful interference, and
- This device must accept any interference received, including interference that may cause undesired
WEEE (Waste of Electrical and Electronic Equipment),
Recycling of Electronic Products
Europe, United Kingdom
- In 2006 the European Union introduced regulations (WEEE) for the collection and recycling of all waste electrical and electronic equipment. It is no longer allowable to simply throw away electrical and electronic equipment. Instead, these products must enter the recycling process.
- Each individual EU member state, as well as the UK, has implemented the WEEE regulations into national law in slightly different ways. Please follow your national law when you want to dispose of any electrical or electronic products. More details can be obtained from your national WEEE recycling agency.
Hersteller / Manufacturer (EU):
68229 Mannheim
Germany
Email: info@lindy.com
T: +49 (0)621 470050
Manufacturer (UK): LINDY Electronics Ltd. Sadler Forster Way Stockton-on-
Tees, TS17 9JY England
sales@lindy.co.uk
T: +44 (0) 1642 754000
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>