SKYDANCE LN-12-12 Constant Voltage LED Driver Instruction Manual

SKYDANCE LN-12-12 Constant Voltage LED Driver

Features

• Dimming interface: 0-10V, 1-10V, 10V PWM, Resistor, AC Push-Dim
• Universal AC input / Full range
• 1 channel constant voltage output, Max. total output power 12W
• Synchronize on multiple LED drivers
• Over-heat / Over-load / Short circuit protection, recover automatically
• Full protective plastic case
• Suitable for indoor LED lighting application
• 5 Year, 50,000hr warranty

Mechanical Structures and Installations

Technical Parameter

Output

| Output Voltage| 12VDC
---|---|---
Output Current| Max. 1A
Output Power| Max. 12W
Dimming Range| 0～100％
Ripple & Noise| <=150mV/230VAC
PWM Frequency| 500Hz

Input

| Input Voltage Range| 100～240VAC
Frequency Range| 50/60Hz
Efficiency| 81％/230VAC
Alternating Current| 0.26A/115VAC, 0.13A/230VAC
Inrush Current| 5A/230VAC
Leakage Current| ＜0.5mA/230VAC
No Load Power| 0.8W/115VAC, 1.2W/230VAC

Protection

| Over Load Power| Shut down the output when current load >= 120％～150％, auto recovers.
Short Circuit| Shut down automatically if short circuit occurs, auto recovers.
Over Temperature| Intelligently adjust or turn off the output current if the PCB temp > 100℃, auto recovers.

Environment

| Woking Temperature| -30℃～50℃
T-case Max| 80℃
Working Humidity| 20％～90％RH, non-condensing
Storage Temperature/Humidity| -40℃～80℃, 10％～95％RH
Temperature Coefficient| ±0.03％/℃ (0-50％)
Vibration Resistance| 10-500Hz, 2G, 6min/cycle, X,Y,Z axes/2min
IP Rating| IP20

Safety&EMC

| Security Specifications| IEC/EN61347-1, IEC/EN61347-2-13
Withstand Voltage| I/P-O/P: 3750VAC
Insulation Resistance| I/P-O/P: 100MΩ/500VDC/25℃/70％RH
EMC Emission| EN55015, EN61000-3-2 Class C, IEC61000-3-3
EMC Immunity| EN61000-4-2.3.4.5.6.8.11, EN61547
Certifications| CE, EMC

Applications

• Suitable for LED-related fixtures or appliances which use LED light bar and LED tape (like LED Decoration or Advertisement devices).
• Office / Commercial / Domestic Lighting, Hotels, Retail and Display.
• Use for retrofit upgrades & new luminaire designs.

Wiring Diagram

0/1-10V Connection

• The 0/1-10V input is operable via commercially available simple rotary wall switches designed for 0/1-10V dimming equipment or from decicated system central dimming controllers.
• Compliant with 0-10V, 1-10V, 10V PWM, RX(4 in 1).
• We recommend the number of LED drivers connected to 0/1-10V dimmer does not exceed 5 pieces, The maximum length of the wires from dimmer to LED driver should be no more than 15 meters.
• If the LED driver be used with Push-Dim interface prior to using the 0/1-10V interface, the 0/1-10 V signal should change over 10% to return 0/1-10 V control.

AC Push-Dim connection

The provided AC Push-Dim interface allows for a simple dimming method using commercially available non-latching (momentary) wall switchs.

Short press:
Turn on or off light.

Long press (1-6s):
Press and hold to step-less dimming, With every other long press, the light level goes to the opposite direction.

Dimming memory:
Light returns to the previous dimming level when switched off and on again, even at power failure.

Synchronization:
If more than one LED driver are connected to the same push switch, do a long press for more than 10s, then the system is synchronized and all lights in the group dim up to 100%. This means there is no need for any additional synchrony wire in larger installation  We recommend the number of LED drivers connected to a push switch does not exceed 25 pieces, The maximum length of the wires from push to LED driver should be more than 20 meters.

Dimming Curve

Documents / Resources

| SKYDANCE LN-12-12 Constant Voltage LED Driver [pdf] Instruction Manual
LN-12-12, Constant Voltage LED Driver, LN-12-12 Constant Voltage LED Driver, Voltage LED Driver, LED Driver, Driver
---|---

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>