Soyal AR-723H Proximity Access Controller User Manual

Soyal AR-723H Proximity Access Controller

Content & Feature

1. Product
2. Terminal Cables
3. Optional
4. Feature
5. Slim design makes installation easy
6. MASTER CARD for adding / deleting tags
7. Set up parameters and user tags by external WG Keyboard
8. Built-in security digital opening signal
9. Built-in Watchdog to prevent from hanging up

Connector Table

Diagram

1. Connect to Electric Strike
2. Connect to Door Contact and Alarm
3. Strengthen security with AR-721RB
4. Connect to Reader or Keyboard
   Please unload the cover before plug in AR-WGKEYBOARD.
   

About Master Card

Enter the program mode

• Use the MASTER CARD software 323DMaster
• Input the MASTER CARD number, and press [Write].
• Cut off and then transmit the power, the master card number will be activated.
• Present the card, and the reader will flash green light 3 times and sound 3 beeps.Then the card becomes MASTER CARD and accesses programming mode.If MASTER CARD is presented again, it will exit programming mode.

Adding Tag

1. Present Master Card
2. After 3 short beeps [Access programming mode]
3. Present the new card or cards one by one till finished the adding.
4. Present Master Card [Exit programming mode]

Deleting All Tags

1. Present Master Card
2. After 3 short beeps[Access programming mode]
3. 1 long warning beep after 2sec.
4. 5 short beeps after 5sec: cards cleared
   P.S. Once MASTER CARD is presented after one warning beep, all card data will be cleared.

Operation process

Enter/ Exit Program Mode

• Enter the program mode
  Input 123456 # or PPPPPP#)
  [e.g.] The Default Value= 123456, if already changed the Master Code= 876112, input j876112# – program mode accessed

• Exit the program mode
  Input* #

• Master Code modification
  Access programming mode→ 09 PPPPPPRRRRRR # [Input the 6-digit new master code twice.] e.g Set the Master code to be 876112, input 123456 #~ 09*J876112876112 #

Set up the password [Only for connect to external K-series reader]

• M4/M8: Individual pass code
  • Card or PIN: Access programming mode 12 UUUUU PPPP # [e.g. User address: 00001 and pass code: 1234, input 12 000011234 # ]
  • Card and PIN: Access programming mode13 JUUUUU JPPPP # [e.g. User address: 00001 and pass code: 1234, input 13 00001 1234 #)I
• M6: Public pass word
  • Card or PIN: Access programming mode 15 *PPPP# [Input 4-digit pass code, default value: 4321]1
  • Card and PIN : Access programming mode17 *PPPP #) [Input 4-digit pass code, default value: 1234; PPPP=0000: change into Card Only]

Lift Control

Connect with AR-401RO16B to control floors which the user will be able to access.

• Enable
  Access programming mode 24 * 002 # [002= enable lift control]

• Single floor
  Access programming mode 27 UUUUU JFF # UUUU=User Address FF=Floor number (01-32 floor) eg] User address NO. 45, allow to access the 24th floor: 27 00045 )24 #)

• Multi floors
  Access programming mode- 21JUUUUU JS FFFFFFFF#
  [UUUUU=User address S: 4 sets of lift control (Input: 0-3) FFFFFFFF: 8 floors setting (F=0=Disable, F=1=Enable)
  [e.g] User address NO. 168, only to the 6th and the 20th floor:
  Access programming mode- 2100168 0 00100000#2100168)2 00001000 #

Setting Up the Arming [Only for connect to external K-series reader Alarm conditions:

1. Arming is enabled
2. Alarm system connected

Application:

1. Door open too long: Door is open longer than door relay time plus door close time.
2. Force open (Opened without a valid user card): Access by force or illegal procedure.
3. Door position abnormal: Arming is enabled and the power is suddenly off then on.

Enable/Disable Arming status (for M4/M8; Factory default armingcode is: 1234)

[The normal procedure to open door] can refer to [Access Mode].

Function Default Value

Selection= O(none value)/ 1(1 x each value) [e.g.] DDD value of Enable “Auto Open” + “Exit by Push Button+ “Anti-pass-back” F(0x1)+(0x2)+(1X4)+(1×16)+(0x32)+(0x64)+(1×128)=148; As a result of that, the command will be 20* 148 Ë

Mode4/ Mode6 / Mode8

Mode 6, the number of users up to 65535, since it reads CARD CODE(5 digits) only, unlike that Mode4/Mode8 read SITE CODE and CARD CODE(10 digits). IF Access Mode setting to use the PIN, it need to external the K-series Readers.

Factory Reset by its commands

When the device is stand-alone (not networking) Access programming mode- 20 016 #24 J064 #-26 EJ00000 01023 )1#28 000 #

Note: After the Master Code is changed, factory reset doesn’t restore the Master Code back to 123456. 29 29 * #

FCC ID: 2ACLEAR-723H

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesired operation.
   Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

NOTE : This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.

If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
•  Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help. The device has been evaluated to meet general RF exposure statement.The device can be used in portable exposure condition without restriction

Warning : Changes or modifications to this unit not expressly approved by the part responsible for compliance could void the user’s authority to operate the equipment This device complies with Industry Canada licence-exempt RSS standard(s).
Operation is subject to the following two conditions:

1. This device may not cause interference, and
2. This device must accept any interference, including interference that may cause undesired operation of the device.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>