mugen seiki B0430F MBX8R Nitro Competition Buggy Instruction Manual

mugen seiki B0430F MBX8R Nitro Competition Buggy

Product Information

Product Usage Instructions

1. Ensure the product is compatible with your radio control system. The product models B0430F, B0430H, B0430J, B0430K, and B0430S are compatible with brands FUTABA, Hitec, JR, KO, and SANWA.
2. Connect the product to your radio control system according to the manufacturer’s instructions.
3. Make sure the radio control system and the product are powered on.
4. Follow the specific instructions provided by your radio control system for binding or pairing the product.
5. Once the product is successfully bound or paired, you can use it to control your RC vehicle or aircraft.
6. Refer to the user manual of your radio control system for detailed instructions on configuring and using the product.
7. If you encounter any issues or have questions, consult the troubleshooting section of the user manual or contact customer support for assistance.

NOTICE: The following items are needed for completion of the MBX8R. They are not included with this kit (unless noted), and should be obtained from your local hobby shop. Be sure to read the instructions completely prior to assembly.

PARTS

Additional items needed for completion.

Additional items needed for starting engine.

Your 2 channel radio svstem
The servos must be set at the center position before installation. To set at a neutral position, turn on the transmitter and receiver. Set the trim tabs in the center position,and turn off the receiver, and then the transmitter. The servos will be in proper neutral position for installation. Please read the instructions provided with your radio svstem before using it.

Tools needed for assemblY

Screw Chart

These are the actual sizes of the screws included with this kit.

ASSEMBLY

1. Front/Rear Diff
2. Center Diff.
3. Front Gear Box
4. Front Lower Arm Note)**** Use E0135A/B/C/E/F to adjust the clearance when installing the front and rear lower arm.
5. Front Upper Arm
6. Front Upright
7. Rear Gear Box
8. Rear Lower Arm
9. Rear Upright
10. Rear Upright / Center Diff. Mount
11. Servo Saver
12. Chassis
13. Fuel Tank
14. Radio Plate
15. Engine
16. Linkage
17. Linkage
    • Adiust each nart to prevent the inkace part from onstrctina the oiner par’s oneration.
    • Turn on the transmitter and receiver and set the engine
    • Control Servo Trim to the neutral position.
    • Adjust the idling adjusting screw on the carburetor to be open approx. 1mm.
    • Adjust the position of E0828A.
    • Adjust the movement of each part to move smoothly.
    • Adjust the engine while it is not running.
    • Adiust ine posttion where ine caroureor is tully open with throttle end oot of transmitter it carburetor is too open or not fully open.
    • No need to use 508288 it shrinkage of cO8 2 is too much.
    • Install E0828B on the position where brake is free with less olay when the rote servo is neutral.
    • he brake applies oo much or nor enouan. change E0828B position, adjust the high brake of transmitter, or turn E0828A to adjust.
    • Turn FOSPSA to acinster brake
18. Shocks
19. Shocks
20. Front Damper
21. Rear Damper
22. Fuel Pipe
23. Air Filter
24. Tire
25. Wing
26. Body
27. Starting Engine
    • Starting Engine
    • Fasten tank cap tightly, after filling fuel. Apply glow engine fuel specially for models.
    • Heat the plug with booster cord or pocket booster.
    • Align a starter’s ring with the flywheel of the car, and try to push the car into the starter, and stanthe engine. ncrease throttle trim 2 or 3 graduations for easy starting. When successfully started, increase RPM until idling stabilize. Then, retur trim to normal.
    • Note: Put a car on car stand so all four wheels are off the ground and rotate freely
    • Stopping Engine
    • Placing idling position, use a rag to cover the exhaust tip. Or. bumping flywheel for instance with the shoes to stop the engine forcibly.
    • Note: Use cloves to protect vour hands from hion temperature exhaust pine.

Troubleshooting Guide

HANDLING OF THE ENGINE RC CAR:

Engine RC car runs at a very fast, and uses expensive flammable glow fuel for the model. Exhaust sound becomes noise sometimes to the other people. Operate the model in the area with safety, no troublesome, no personal injury, no property damage, and no accident.

After assembling

1. Be sure to tight screws securely and install all parts.
2. Make sure whether the movable parts work smoothly.
3. Turn on the switch of the receiver and transmitters, and makesure whether the steering servo and engine control servo work normally.

Do not operate it:

1. In the place where many people around
2. near children
3. near the residential districts, school, and hospital
4. near the road and railroad track
5. indoors
6. at early morning and at night
7. at the same time when somebody uses the same frequency
8. when the battery of receiver and transmitter weak
9. when the model behave strangely

Start to operate
Be sure to observe the following process. Non-observance will make RC car start suddenly, and may lead the damage and unexpected accident.

1. Make sure the battery charges fully.
2. Put the RC car on the starter box and float the tires from the ground.
3. Turn on the switch of the receiver.
4. Turn on the switch of the transmitter.
5. Make sure the steering servo and engine control servo worknormally and adjust them correctly.
6. Put the fuel in the tank, and close the cap securely.
7. Heat the plug.
8. Push the back of RC car on the starter box and start the engine.(If the engine is new, follow the instruction manual and be sure to smooth new engine. If not, engine will break suddenly by the high rotation.)

Finish to operate

1. Stop the engine. (Use up the fuel in the tank or force to stop the flywheel that is seen from the bottom of the chassis by the sole of shoe, etc.)
2. Turn off the switch of the receiver.
3. Turn off the switch of the transmitter.

Maintenance after running

Do care after running to keep performance, and to notice the damage and the wear.

1. Do not leave the fuel in the tank.
2. Exhaust oil insides the muffler should go outside.
3. Clean up the sand and mud.
4. Put the oil on the movable parts such as shaft carrier, suspension, etc and the bearing.
5. Put the rustproof oil (maintenance oil) inside of the engine.

CAUTION: FUEL
The glow fuel for radio control models that is used for the engine RC car is made of the combination of the methyl alcohol, the oil or composition oil, nitro methane etc. The flammability of these elements is to be very high, have volatility, be fully careful of handling and the storage.

• Only use the glow fuel for radio control models the model shop sells. Other fuel, such as the gasoline and kerosene may break engine, and there is fear of explosion and accident such as a fire. Never use it.
• The flammability of the fuel is very high. Don’t do the fuel lubrication and the preparation for operating near the fire.
• Never do handling of the lubrication in the inside and mixing of the fuel in the place where ventilation is bad.
• Fuel is harmful. It is dangerous to drink and to inhale the volatile element of the fuel and exhaust. Never do.
• Avoid fire, direct sunlight, high temperature, near battery and store the fuel in the cool, dry and dark places out of  children’s reach.Don’t leave the fuel in the fuel pump and the fuel tank. There is danger that fuel leaks out. Wipe out the spilt fuel with the useless cloth completely.
• Remove a cap first and throw the empty fuel can away. Don’t throw an empty can into the fire. There is danger of explosion.

CAUTION: ENGINE
Confirm the position of needle and idling before running. Be sure to smooth new engine.

Never remodel engine and muffler.

• There is danger that it gets burned because around the engine and the muffler generate high temperature for a while after use.
• Do not touch the rotating parts at high speed such as clutch bell and flywheel. There is danger that it gets hurt.
• If the fuel pipe is choked or deteriorates, the engine may not start and there is danger the fuel leaks out.
• Be sure to put the air filter. Use the filter that is soaked air filter Oil.
• Engine may not start if the air filter is dirty, choked with the sand and dust.

FIRST AID

• If you drink fuel by accident, drink large quantities of water and emit it and right after that, see a doctor. If fuel is within eyes, wash if away with the water well, and right after that, see a doctor.
• If fuel is stuck to the skin, wash it with soap and water

CONTACT

• 20525 Crescent Bay Drive
• Lake Forest, CA 92630, USA
• E-mail: support@mugenracing.com.
• www.mugenracing.com.

The contents are subject to change without notice due to product improvements and specification changes.
WARNING: This product CONTAINS CHEMICALS which and known to the state of Califomia to cause cancer. birth defects. or other reproductive harm.
NOTICE: The following items are needed for completion of the MBX8R. They are not included with this kit (unless noted), and should be obtained from your local hobby shop. Be sure to read the instructions completely prior to assemblv.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>