tp-link AX1800 Archer Nano User Guide

: September 28, 2024
: tp-link

Table of Contents

tp-link AX1800 Archer Nano
About This Guide
Get to Know About Your Adapter
Use the Adapter
Troubleshooting
FCC compliance information statement
Safety Information
Documents / Resources

tp-link AX1800 Archer Nano

About This Guide

This guide is a complement to Quick Installation Guide. The Quick Installation Guide instructs you on quick installation, and this guide provides the product overview and detailed instructions for each steps.
When using this guide, please notice that features available of the adapter may vary by model and software version. It may also vary by region or ISP. All images, steps, and descriptions in this guide are only examples and may not reflect your actual experience.

Conventions
In this guide, the following conventions are used:

Convention	Description
Underlined	Underlined words or phrases are hyperlinks. You can click to

redirect to a website or a specific section.
Teal| Contents to be emphasized and texts on the web page are in teal, including the menus, items, buttons, etc.
Note:| Ignoring this type of note might result in a malfunction or damage to the device.
Tips:| Indicates important information that helps you make better use of your device.

†Maximum wireless signal rates are the physical rates derived from IEEE Standard 802.11 specifications. Actual wireless data throughput, wireless coverage, and number of connected devices are not guaranteed and will vary as a result of network conditions, AP limitations, and environmental factors, including building materials, obstacles, volume and density of traffic, and AP location.
‡Use of Wi-Fi 6 (802.11ax), and features including OFDMA, MU-MIMO, and 1024-QAM require APs to also support the corresponding features.
§Functionality of Archer TX1800U Nano may be restricted on some operating systems and platforms.
Please try to update the device’s driver for feature compatibility.

Use of WPA3 requires APs to also support the corresponding feature.
*Actual network speed may be limited by the rate of the product’s USB port, PCI Express Interface, Ethernet WAN or LAN port, the rate supported by the network cable, internet service provider factors, and other environmental conditions.

More Info

The latest driver can be found at Download Center at https://www.tp-link.com/support
The Quick Installation Guide can be found where you find this guide or inside the package of the router
Specifications can be found on the product page at https://www.tp-link.com
A TP-Link Community is provided for you to discuss our products at https://community.tp-link.com
Our Technical Support contact information can be found at the Contact Technical Support page at https://www.tp-link.com/support

Get to Know About Your Adapter

This chapter introduces what the adapter can do and shows its appearance. This chapter contains the following sections:

Product Overview
TP-Link Wireless USB Nano Adapter connects your computer to a Wi-Fi network for smooth HD video, voice streaming and online gaming. Plug it, foget it.

Arm Your PC with Wi-Fi 6 Technology – Archer TX1800U Nano arms your PC with Wi-Fi 6 to ensure powerful, continuous signal reception, unlocking your Wi-Fi 6 router’s full potential.
Boosted Throughput with MU-MIMO – Works with MU-MIMO routers, which provide simultaneous data streams, boosting throughput and efficiency.‡
Improved Security with WPA3 – The latest Wi-Fi security protocol provides enhanced protection in personal password safety. △
Tiny in Size, Mighty in Performance – Much smaller than regular USB flash drive, enjoy a stable and super-fast Wi-Fi wherever you need it.

LED Status

You can check the adapter’s working status by following the LED explanation table.

Status	Indication
On	The driver has been installed successfully.
Off	The driver is not installed. The adapter is not detected.

Tips:
If the LED is off, try these troubleshooting tips:

Check if the adapter is recognized and enabled or not. Refer to Appendix: Troubleshooting for detailed instructions.
Remove and reinsert the adapter.
Reinstall the software, if necessary.

Use the Adapter

This chapter introduces how to install your adapter’s driver, use your adapter to join a wireless network, and uninstall your adapter in a Windows system. The adapter is equipped with a Setup Wizard, which can guide you through the installation process.
This chapter includes the following sections:

Install Driver
Join a Wireless Network
Uninstall Driver

Install Driver

Insert the adapter into a USB port on your computer.
Go to My Computer or This PC.
Double click the TP-Link CD-ROM then run SetupInstall.exe to install driver.

Note:

If you cannot find the setup program, please download the driver at www.tp-link.com/support.
If an unknown publisher message pops up, select Yes to continue.
If Windows User Account Control requires admin credentials, type user name and password of your Windows administrator account.

Join a Wireless Network
You can join a wireless network via Windows built-in wireless utility. Follow the instructions below to use your computer system’s built-in wireless utility:

Click the network icon on the taskbar (the icon might look like one of these:
Select the Wi-Fi network you want to join, and click Connect. Enter the network password when prompted.

Uninstall Driver
The software uninstallation steps vary a bit from different systems. Here we take the instructions for Windows 10 as an example.
Go to Contol Pannel > Programs, click Uninstall a program, then double-click TP-Link Archer TX1800U Nano Driver, then follow the on-screen instructions to complete the uninstallation.

Troubleshooting

T1. What should I do if the adapter is not detected?

Make sure the adapter is securely connected to the computer.
Make sure you meet the minimum system requirements for the adapter and that the latest Windows and system updates are installed on your computer.
Make sure you use the latest driver for your specific adapter. The latest drivers can be found at https://www.tp-link.com/download-center
Try a different USB port on the computer.
Try restarting the computer or try using the adapter on a different computer.

T2. How to check if I have installed the driver for my adapter successfully or not?

On your computer, please right click Computer icon and go to Manage;
Open the Device Manager and go to Network adapters, and then find the corresponding TP-Link adapter, right click it and then go to Properties;
If you can see “This device is working properly.” in the red box, you have already.

T3. What should I do if can’t connect to the Wi-Fi after installing the driver?

Refer to T2 to check if you have installed the driver for your adapter successfully.
Make sure the adapter is securely connected to the computer.
Disable the antivirus software and firewall, then try again.
Try a different USB port on the computer.
Restart your computer and try again.
Re-install the driver and try again.

T4. How to find the hardware version of the adapter?

The hardware version is printed on the product label on the package or the adapter. There is a character string “Ver: X.Y” (for example, Ver:2.0) in the Serial Number field, and the number X is the hardware version of the adapter.
Visit https://www.tp-link.com/faq-46.html and follow the second method to find the hardware version of the adapter.

For more detailed instructions

Can’t find the hardware version of the adapter: https://www.tp-link.com/faq-46.html
Can’t find or join the wireless networks: https://www.tp-link.com/faq-2253.html
Can’t install the driver: https://www.tp-link.com/faq-2252.html

FCC compliance information statement

Product Name: AX1800 Nano Wi-Fi 6 Wireless USB Adapter
Model Number: Archer TX1800U Nano
Responsible party: TP-Link USA Corporation
Address : 10 Mauchly, Irvine, CA 92618
Website : https://www.tp-link.com/us/
Tel : +1 626 333 0234
Fax : +1 909 527 6804
E-mail: sales.usa@tp-link.com

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/ TV technician for help.

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

This device may not cause harmful interference.
This device must accept any interference received, including interference that may cause undesired operation.
Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

Note : The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment. Such modifications could void the user’s authority to operate the equipment.

FCC RF Radiation Exposure Statement
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. End users must follow the specific operating instructions for satisfying RF exposure compliance. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. This equipment has been SAR-evaluated for use in hand. SAR measurements are based on a 5mm spacing from the body and that compliance is achieved at that distance.

We, TP-Link USA Corporation, has determined that the equipment shown as above has been shown to comply with the applicable technical standards, FCC part 15. There is no unauthorized change is made in the equipment and the equipment is properly maintained and operated.

CE Mark Warning
This is a class B product. In a domestic environment, this product may cause radio interference, in which case the user may be required to take adequate measures.

OPERATING FREQUENCY (the maximum transmitted power)
2400 MHz -2483.5 MHz(20dBm)
5150 MHz -5250 MHz(23dBm)
5250 MHz -5350 MHz (23dBm)
5470 MHz -5725 MHz (23dBm)

EU declaration of conformity
TP-Link hereby declares that the device is in compliance with the essential requirements and other relevant provisions of directives 2014/53/EU, 2011/65/EU and (EU)2015/863. The original EU declaration of conformity may be found at
https://www.tp-link.com/en/ce

TP-Link hereby declares that the device is in compliance with the essential requirements and other relevant provisions of the Radio Equipment Regulations 2017.
The original UK declaration of conformity may be found at https://www.tp- link.com/support/ukca/

RF Exposure Information
This device meets the EU requirements (2014/53/EU Article 3.1a) on the limitation of exposure of the general public to electromagnetic fields by way of health protection.
This device has been tested and meets the ICNIRP exposure guidelines and the European Standard EN 62209-2. SAR is measured with this device at a separation of 0.5 cm to the body while transmitting at the highest certified output power level in all frequency bands of this device. Carry this device at least 0.5 cm away from your body to ensure exposure levels remain at or below the as-tested levels.

National restrictions

Frequency band: 5150 – 5250 MHz:
Indoor use: Inside buildings only. Installations and use inside road vehicles and train carriages are not permitted. Limited outdoor use: If used outdoors, equipment shall not be attached to a fixed installation or to the external body of road vehicles, a fixed infrastructure or a fixed outdoor antenna. Use by unmanned aircraft systems (UAS) is limited to within the 5170 – 5250 MHz band.

Frequency band: 5250 – 5350 MHz:
Indoor use: Inside buildings only. Installations and use in road vehicles, trains and aircraft are not permitted. Outdoor use is not permitted.

Frequency band: 5470 – 5725 MHz:
Installations and use in road vehicles, trains and aircraft and use for unmanned aircraft systems (UAS) are not permitted.

Attention : This device may only be used indoors in Great Britain.

Canadian Compliance Statement
This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions:

This device may not cause interference.
This device must accept any interference, including interference that may cause undesired operation of the device.

Caution
The device for operation in the band 5150–5250 MHz is only for indoor use to reduce the potential for harmful interference to co-channel mobile satellite systems;
DFS (Dynamic Frequency Selection) products that operate in the bands 5250- 5350 MHz, 5470-5600MHz, and 5650-5725MHz.

Radiation Exposure Statement
This EUT is compliance with SAR for general population/uncontrolled exposure limits in RSS-102 and had been tested in accordance with the measurement methods and procedures specified in IEEE 1528 and IEC 62209. This equipment should be installed and operated with minimum distance 0.5 cm between the radiator and your body. This device and its antenna(s) must not be co-located or operating in conjunction with any other antenna or transmitter.

Safety Information

Keep the device away from water, fire, humidity or hot environments.
Do not attempt to disassemble, repair, or modify the device. If you need service, please contact us.
Do not use the device where wireless devices are not allowed.
This equipment can be powered only by equipments that comply with Power Source Class 2 (PS2) or Limited Power Source (LPS) defined in the standard of IEC 62368-1.
This product uses radios and other components that emit electromagnetic fields. Electromagnetic fields and magnets may interfere with pacemakers and other implanted medical devices. Always keep the product and its power adapter more than 15 cm (6 inches) away from any pacemakers or other implanted medical devices. If you suspect your product is interfering with your pacemaker or any other implanted medical device, turn off your product and consult your physician for information specific to your medical device.

Operating Temperature: 0°C~40°C (32°F ~104°F)
Please read and follow the above safety information when operating the device. We cannot guarantee that no accidents or damage will occur due to improper use of the device. Please use this product with care and operate at your own risk.

Explanation of the symbols on the product label