SOYAL AR-888-PBI-S Touchless Infrared Button Instruction Manual

May 21, 2024
SOYAL

AR-888-PBI-S Touchless Infrared Button

Product Information: SOYAL AR-888-PBI-S Touchless Infrared

Button

The SOYAL AR-888-PBI-S is a touchless infrared button used for access and industrial control. It comes with 2 terminal cables and 3 tools for installation. The product has a CN1 connector table with dip switches, LED status, and adjustment. It also has a built-in resistor and requires an external power supply current exceeding 20mA.

The product has 2 dip switch settings for output format and 4 sensing distance adjustments. It also has 3 LED status adjustments for standby mode, motion, and example #2. The product comes with wiring diagrams for electric bolt, electric strike, magnetic lock, request to exit, and door sensor. It also has a wiring diagram for LED R/G door status indication. The product requires AWG 22-24 shielded twist pair or CAT5 for TCP/IP connection.

Installation Instructions

  1. Pull the cables from the square holes of the eva foam gasket and mounting plate.
  2. Use a screwdriver to screw the mounting plate onto the wall with flat head cap Philips tapping screws (excluded, the installer should prepare before installation).
  3. Connect the cables to the backside of body C and attach C to B at lower position of B.
  4. Push C up to make the cogging hooked completely.
  5. Use the Allen key and screws to assemble the body C onto the mounting plate B.
  6. Attach the back cover D to C.
  • US Mounting Hole: 73x48x40mm(HxWxD)
  • Screw hole pitch : 84mm
  • Suitable for 70X118 1-module flush-mounting box.( Australian, Italy, USA(501E) Standard)
  • EU Mounting Hole: 57x53x40mm(HxWxD)
  • Screw hole pitch : 60mm
  • Suitable for 86X86 flush-mounting box.
    (UK, Continental Europe, Germany Standard)

The product has an in-wall depth of 28mm to 35mm and comes with an easy install kit (by order). The mounting hole for US is 73x48x40mm (HxWxD) with a screw hole pitch of 84mm. It is suitable for 70×118 1-module flush-mounting box (Australian, Italy, USA(501E) Standard). The mounting hole for EU is 57x53x40mm (HxWxD) with a screw hole pitch of 60mm. It is suitable for 86×86 flush-mounting box (UK, Continental Europe, Germany Standard).

Installation

AR-888-PBI-S: Touchless Infrared Button

Connector Table / Dip_switch

CN1 Connector:

Dip Switch Setting

Default Value

Output Format

No.| SW1| SW2| Description
※ 1| OFF| OFF| No Delay
2| OFF| ON| Delay 3 Seconds
3| ON| OFF| Delay 6 Seconds
4| ON| ON| Toggle Mode
Sensing Distance Adjustment

No.| SW3| SW4| Description
※ 1| OFF| OFF| 1: Max. range 10cm
2| OFF| ON| 2: Medium range
3| ON| OFF| 3: Short range
4| ON| ON| 4: Min. range 2cm

LED status adjustment

Wiring Diagrams

*The Wiring Diagram of LED R/G Door Status Indication



Type A

| The magnetic circuit will be turned on when getting closed to the switch. (closed circuit).

The magnetic circuit will be turned off after removed the magnet. (open circuit)

Double contact–NO. / COM

---|---


Type C

| Trigger LED R when door open Trigger LED G when door closed Triple contact – NO. / NC. / COM

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals