MEEC TOOLS 012148 Car Garage Jack Instruction Manual
- June 5, 2024
- MEEC TOOLS
Table of Contents
2,5 T / 75-510 mm
GARAGE JACK
Item no. 012148
OPERATING INSTRUCTIONS GARAGE JACK
Important! Read the user instructions carefully before use. Save them for
future reference. (Translation of the original instructions)
Jula reserves the right to make changes. In the event of problems, please
contact our service department. www.jula.com
Distributör
2022-02-25
© Jula AB
Jula AB box 363
This declaration of conformity is issued under the sole responsibility of the manufacturer
LOW PROFILE GARAGE JACK 2,5T,2500kg
Item number
012148
conforms to the following directives and standards
Machinery Directive 2006/42/EC, EN 1494+A1:2008
This product was CE marked in the year -20
Name and address of the person
authorized to compile the technical file: Viktoria Klaar Box 363, SE-532 24
Skara, Sweden
Skara 2020-02-18
Christian Blank
BUISNESS AREA MANAGER
SAFETY INSTRUCTIONS
- It’s forbidden to use the jack to lift people.
- Center the load on the saddle before lifting.
- Never work under a vehicle without blocking it up on pallet blocks (or equivalent).
- Always check the wheels on the vehicle and pull the handbrake on.
- Do not push or lean on the vehicle when it is resting on the jack.
- Only use the lifting points specified by the vehicle manufacturer.
- Do not take the jack apart – the risk of injury or malfunctioning.
- Before lifting a vehicle, check that the jack is in good working condition.
- Do not attempt to lift or support foundations, houses, caravans, trailers, campers etc
- The product is only intended to be used for lifting. Never attempt to move the vehicle when it is resting on the product
- Never overload the jack – risk of personal injury and/or material damage.
- Only use the lifting points specified by the vehicle manufacturer.
- The product is intended to be used on hard, level surfaces that can support the actual load. If the jack is placed on any other surface the product can become unstable and the load can fall
- Never go under a vehicle that is only lifted up with the jack.
- Only use spare parts recommended by the manufacturer.
- Failure to follow all the instructions and safety instructions can result in a risk of personal injury and/or material damage.
Symbols
| Read the instructions.
---|---
| Approved in accordance with the relevant directives.
TECHNICAL DATA
| Lifting power | 2.5 tonnes |
|---|---|
| Lifting height | 75 – 510 mm |
| Double pistons | Yes |
| Size | 724 x 342 x 153 mm |
| Weight | 30,6 kg |
USE
IMPORTANT:
Air in the hydraulic system can impair performance. Bleed the product
before using it for the first time by completely opening the lowering valve
(turn the handle anticlockwise) and then press down the lifting saddle and
pump rapidly several times with the pump handle.
LIFTING
- Close the lowering valve by turning the handle clockwise until it resists. Do not overtighten.
- Place the product under the object to be lifted. Check that the middle of the lifting saddle comes directly under the part that is to be lifted. Check that the lifting saddle is correctly positioned by lifting the object a little and checking that the product or he cannot slip or move unexpectedly.
- Lift the load by pumping with the handle to the required height. Block up the load immediately after lifting, with pallet boxes or the equivalent. Never let the load rest only on the jack.
LOWERING
Turn the handle anticlockwise slowly.
The lowering speed depends on how much the
The lowering valve is opened.
MAINTENANCE
STORAGE
Always store the product in the fully lowered position with the handle
upright.
BLEEDING
Bleed the product before using it for the first time by completely opening the
lowering valve (turn the handle anticlockwise) and then press down the lifting
saddle and pump rapidly several times with the pump handle.