dji TX2 Ronin 4D Video Transmitter Instructions
- June 5, 2024
- DJi
Table of Contents
dji TX2 Ronin 4D Video Transmitter
FCC Compliance Notice
Supplier’s Declaration of Conformity
- Product name: DJI Ronin 4D Video Transmitter
- Model Number: TX2
- Responsible Party: DJI Technology, Inc.
- Responsible Party Address: 201 S. Victory Blvd., Burbank, CA 91502
- Website: www.dji.com
We, DJI Technology, Inc., being the responsible party, declare that the above
mentioned model was tested to demonstrate complying with all applicable FCC
rules and regulations.
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) This device must accept any interference received,
including interference that may cause undesired operation. Any changes or
modifications not expressly approved by the party responsible for compliance
could void the user’s authority to operate the equipment. This equipment has
been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the
following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
The portable device is designed to meet the requirements for exposure to radio waves established by the ISED. These requirements set a SAR limit of 1.6 W/kg averaged over one gram of tissue. The highest SAR value reported under this standard during product certification for use when properly worn on the body.
ISED Compliance Notice
This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions: (1)This device may not cause interference.(2)This device must accept any interference, including interference that may cause undesired operation of the device. This equipment complies with ISED radiation exposure limits set forth for an uncontrolled environment. End user must follow the specific operating instructions for satisfying RF exposure compliance. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. The portable device is designed to meet the requirements for exposure to radio waves established by the ISED. This equipment complies with RSS 102 radiation exposure limits set forth for an uncontrolled environment. End user must follow the specific operating instructions for satisfying RF exposure compliance. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. The portable device is designed to meet the requirements for exposure to radio waves established by the ISED. These requirements set a SAR limit of 1.6 W/kg averaged over one gram of tissue. The highest SAR value reported under this standard during product certification for use when properly worn on the body. No operation is permitted for the frequency “5600-5650MHz”
- For devices with detachable antenna(s), the maximum antenna gain permitted for devices in the bands 5250-5350 MHz and 5470-5725 MHz, 5725-5850 MHz shall be such that the equipment still complies with the e.i.r.p. limit as appropriate; and
- This radio transmitter 23060-TX2202109 has been approved by Innovation, Science and Economic Development Canada to operate with the antenna types as Dipole antenna. Antenna 0-3 at 2400-2483.5 MHz, with the maximum permissible Gain is 2.5 dBi; Antenna 0-3 at 5250-5725 MHz, with the maximum permissible Gain is 2.5 dBi; Antenna 0-3 at 5725~5850 MHz, with the maximum permissible Gain is 3 dBi). Antenna types not included in above information that have a gain greater than the maximum gain indicated for any type listed are strictly prohibited for use with this device. The required impedance for each antenna type designed in 50ohm.
EU Compliance Statement
SZ DJI Osmo Technology Co., Ltd. hereby declares that this device (DJI Ronin 4D Video Transmitter) is in compliance with the essential requirements and other relevant provisions of the Directive 2014/53/EU. A copy of the EU Declaration of Conformity is available online at www.dji.com/euro- compliance EU contact address: DJI GmbH, Industriestrasse 12, 97618, Niederlauer, Germany
GB Compliance Statement
SZ DJI Osmo Technology Co., Ltd. hereby declares that this device (DJI Ronin 4D Video Transmitter) is in compliance with the essential requirements and other relevant provisions of Radio Equipment Regulations 2017. A copy of the GB Declaration of Conformity is available online at www.dji.com/euro- compliance
Environmentally friendly disposal
Old electrical appliances must not be disposed of together with the residual waste, but have to be disposed of separately. The disposal at the communal collecting point via private persons is for free. The owner of old appliances is responsible to bring the appliances to these collecting points or to similar collection points. With this little personal effort, you contribute to recycle valuable raw materials and the treatment of toxic substances.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>