concept ZN 8022 Electric Steam Iron Instruction Manual
- June 5, 2024
- concept
Table of Contents
Steam Iron
ZN 8022
ZN 8032
Instruction Manual
ACKNOWLEDGMENT
Thank you for purchasing a Concept product. We hope you will be satisfied with
our product throughout its service life.
Please study the entire Operating Manual carefully before you start using the
product. Keep the manual in a safe place for future reference. Make sure other
people using the product are familiar with these instructions.
Technical parameters
Model| ZN 8022| ZN 8032
Power input| 2 000 W| 2 200 W
Voltage| 220-240 ∼ 50/60 Hz| 220-240 ∼ 50/60 Hz
Anodia ironing surface| •| •
SELF-CLEAN| •| •
ANTI-DRIP| •| •
ANTI-CALC| •| •
AUTO SHUT-OFF| –| •
IMPORTANT SAFETY PRECAUTIONS:
- Use the unit only as described in this operating manual.
- Remove all the packaging and marketing materials from the unit before the first use.
- Make sure the mains voltage corresponds to the values on the rating plate. Use grounded wall outlets only.
- The unit reaches high temperatures during operation and remains hot for some time after being turned off. Do not touch the hot surfaces. Use the handles and buttons. There is a risk of being burned.
- Do not leave the unit unattended while it is turned on or even only plugged into the wall outlet.
- Unplug the unit from the wall outlet when not in use.
- When disconnecting the unit from the wall outlet, never pull the power cord. Grasp the plug and disconnect it by pulling.
- Do not allow children or unskilled people to handle the unit. Use the unit out of the reach of these individuals.
- A person with limited movement capacities, reduced sensory perception, insufficient mental capacity, or those who are unaware of the proper handling shall use the product only under the supervision of a responsible, aware person.
- Take extra care when using the unit near children.
- Don’t let anyone use the unit as a toy.
- Use only accessories recommended by the manufacturer.
- Never use an appliance with a damaged power cord or plug. Contact an authorized service center immediately to have defective components repaired or replaced.
- Keep the vacuum cleaner away from heat sources such as radiators, ovens, and so on. Do not expose the product to direct sunlight or moisture.
- Do not touch the unit with wet or damp hands.
- The unit is suitable for domestic use only. It is not designed for commercial operation.
- Do not immerse the power cord, plug, or appliance into water or any other liquid.
- Check the appliance and power cord for damage regularly. Do not switch on a damaged unit.
- Turn the unit off, unplug the power cord from the wall outlet, and let the unit cool before cleaning and after use.
- Unplug the unit from the power source before filling the water tank.
- The filling hole cannot be open during operation.
- When connecting and unplugging the unit, set the temperature regulator to the minimum.
- The unit must be used and stored on a stable surface.
- Make sure the ground on which the stand is placed is stable when putting the unit on the stand.
- Do not use the unit if it has been dropped, if there is any visible damage, or if it does not seal.
- Do not repair the appliance yourself. Contact an authorized service center.
- Prevent any contact of the power cord with hot surfaces.
- High temperatures during operation can cause burns.
- Make sure the power cord does not overhang the working area, and that children cannot reach it.
- Store the unit in a vertical standing position. Let the unit cool down before storing it. Do not touch the hot surfaces.
Failure to follow the manufacturer‘s instructions may lead to refusal of warranty repair.
- This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge unless they have been given supervision or instruction concerning the use of the appliance by a person responsible for their safety.
- Children should be supervised to ensure that they do not play with the appliance.
**PRODUCT DESCRIPTION
**
- Filling hole cover
- Steam volume regulator
- Spray button
- Steam button
- Automatic OFF indicator (ZN8009)
- Temperature controller
- Supply cable joint
- Heating indicator
- Ironing surface
- Water tank
- Self-clean button
- Spray nozzle
Accessories
A Water tank
OPERATING INSTRUCTIONS
Do not leave the unit unattended if it is connected to the power source.
Remove all the stickers and packaging from the ironing surface before the
first use.
Before the first ironing, try the unit on a piece of old fabric to make sure
the ironing surface and water tank are perfectly clean.
The unit may emit a slight odor during the first use. This smell will vanish
after a short time.
Filling with water
- Unplug the unit from the power source.
- Set the temperature controller to the minimum.
- Open the filling hole cover (Fig. 1)and fill the tank with water. Use only distilled or boiled water. Don‘t fill the tank with a liquid other than water. Do not put any additions in the water. There is a risk of damage to the unit. The capacity of the tank is about 350 ml. Do not exceed the maximum marked water level.
- Close the filling hole cover.
Spraying
Push the spray button; water is released through the spray nozzle. You will
need a sufficient volume of water in the tank to activate this function.
Steam ironing
- For steam, ironing set the steam volume regulator to the minimum, and the temperature controller according to the material „…“, „…“ or „MAX“
- After the heating indicator goes off, set the steam volume regulator to the required position, the steam will start to release, and you may begin ironing.
Steam shock
Turn the temperature controller to the position „…“ or „ M A X “, and push the
steam button – the ironing surface will emit steam. Wait for a couple of
seconds before
the next push.
You may use this function for ironing in a vertical position to smoothen folds
on hanging clothes or curtains. Hold the unit several centimeters from the
fabric to prevent damage to soft materials.
Never iron any clothing on the body!
Ironing
- If you want to use the spray or steam function, fill the tank with water (see Filling with Water).
- Set the temperature controller to the minimum.
- Insert the plug into the main outlet.
-
Set the temperature controller to the value that corresponds to the material to be ironed (according to the international textile codes). The heating indicator will be illuminated.
Note: Iron fabrics that require a lower temperature first, then those at higher temperatures. Most fabrics are marked according to international codes – see the table below. Note:
The symbol on the tag means: “This fabric must not be ironed!”Tag with ironing info| Fabric type| Temperature setting| Steam setting
| Synthetic
Polypropylene
Polyurethane
Polyamide
Polyester
Viscose| |
| Silk
Wool
| Cotton
Linen - Wait until the heating indicator stops shining. Only then has the ironing surface reached the right temperature. The ironing surface will be heated during ironing. The heating indicator will turn on and off.
- After use, set the temperature controller to the minimum, unplug the unit from the power source, and let it cool down. Then pour the remaining water out of the tank.
Anti-dripping function (ANTI-DRIP)
This unit is equipped with a function that prevents water from dripping, i.e.
it will automatically stop steaming if the temperature is too low and water
could be dripping from the ironing surface.
Limescale sedimentation preventive function (ANTI-CALC)
This function is based on the filtration of materials from the water used. It
softens the used water, which reduces the sedimentation of limescale in the
steam chamber.
Self-clean function
This function allows cleaning small sediments from the steam chamber. Use it
once every two weeks.
- Fill the tank with water (see Filling with Water).
- Insert the plug into the main outlet.
- Set the temperature control to the maximum.
- Wait until the heating indicator light stops shining.
- Hold the unit horizontally over a sink or wide water vessel.
- Push and hold the Self-clean button. Water will pour from the steam holes in the ironing surface, which will rinse out small sediments from the steam chamber.
Automatic SHUT OFF function – available on model ZN 8009 only
This safety feature allows automatic shut-off if the unit is left on a
horizontal ironing surface for 30 seconds without moving, or for 8 minutes in
the vertical position without moving.
In these cases the unit will shut off automatically, a short beep will be
heard, and the automatic shut-off indicator will start blinking.
Note: This function is just a safety measure. For normal use, set the
temperature controller to the minimum, and unplug the unit from the power
source.
STORAGE
Keep the cooling unit in a vertical and stable position in a safe and dry place, out of the reach of children.
CLEANING AND MAINTENANCE
Unplug the unit from the power source.
Remnants of fabric fibers may be stuck to the ironing surface. Remove them
with a soft cloth soaked in water and vinegar. Then wipe the surface using a
dry cloth.
Do not use any abrasives or steel wool to clean the ironing surface. Keep the
ironing surface smooth; prevent it from coming into contact with hard metal
objects. Make sure the ironing surface is not scratched or damaged.
Clean the body with a wet cloth. Do not use aggressive substances for
cleanings, such as solvents or abrasives!
Do not pour vinegar or other limescale removers into the water tank. To clean
the steam holes, use a wet cloth, and remove lumps and dust from the internal
parts of the holes.
Do not immerse the power cord, plug, or appliance into water or any other
liquid.
REPAIR & MAINTENANCE
Any extensive maintenance or repair that requires access to the inner parts of the product must be performed by an expert service center.
ENVIRONMENTAL PROTECTION
- Packaging materials and obsolete appliances should be recycled.
- The transport box may be disposed of as sorted waste.
- Polyethylene bags shall be handed over for recycling.
- Packaging materials and obsolete appliances should be recycled.
- The transport box may be disposed of as sorted waste.
- Polyethylene bags shall be handed over for recycling.
Appliance recycling at the end of its service life:
A symbol on the product or its packaging indicates that this product should
not go into household waste. It must be taken to the collection point of an
electric and electronic equipment recycling facility. By making sure this
product is disposed of properly, you will help prevent the negative effects on
the environment and human health that would otherwise result from the
inappropriate disposal of this product. You can learn more about recycling
this product from your local authorities, a household waste disposal service,
or in the shop where you bought this product.
It must be taken to the collection point of an electric and electronic
equipment recycling facility. By making sure this product is disposed of
properly, you will help prevent the negative effects on the environment and
human health that would otherwise result from the inappropriate disposal of
this product.
WARRANTY TERMS
Warranty The manufacturer (or importer) is responsible for ensuring the
product complies with the requirements of applicable legal regulations as well
as those of the relevant technical standards. Moreover, they are responsible
for ensuring the product has the properties the manufacturer described in
documents related to the goods or those reasonably expected by the customer
with regard to the nature of the goods or based on advertising produced by the
manufacturer, and further, they are responsible for ensuring the product is fi
t for the purpose proposed by the manufacturer or that a product of the same
type is normally used for.
The quality warranty term is 24 months from product takeover by the customer.
The warranty does not apply to wear and tear caused by regular use. The
customer shall not be entitled to any warranty claims if, prior to taking the
product over, they knew the product contained a defect or if the defect is
attributable to the customer.
The warranty specifically does not apply:
- if the product installation, operation, and service conditions stipulated in the product operating manual have not been adhered to,
- to malfunctions caused due to mechanical, heat, or chemical damage, short circuit, over-voltage, or incorrect installation,
- to malfunctions caused by an inexpert third-party intervention,
- to malfunctions caused by natural disasters,
- to malfunctions caused by insufficient or inappropriate maintenance in violation of the operating manual, including malfunctions caused by water and other sediments,
- to changes in color of the heating surface or to scratching of the surface caused as a result of using the products in an unusual manner,
- to appearance and functional changes caused by exposure to sunlight, thermal radiation of water and other sediments,
- if the service life of certain product parts expires, e.g. for accumulators, bulbs, etc.
The warranty does not apply to any products and services provided along with the product (gifts, promotional articles, etc.).
Filing a complaint
A complaint against a product defect must be fi led as soon as identifi ed, yet
no later than before the end of the warranty term. The customer must fi le a
product compliant with the dealer from which they have purchased the product,
or with any authorized service center, a list of which is included in the
product package, or available at
www.my-concept.com.
While filing a product complaint, the product must be duly cleaned and
securely packed so as to prevent any damage during its transport to an
authorized service center, where relevant, unless the product is delivered in
person.
The customer must submit proof of having concluded a purchase contract for the
product by producing the receipt.
While fi ling their complaint, the customer must indicate the noted defect and
identify the preferred complaint application method.
Complaints processing
As long as the noted defect may be removed, the user has the right to have the
defect duly removed free of charge on a timely basis.
Where such a procedure is not reasonable with regard to the nature of the
defect, the user may require to be supplied a new defect-free product
(replacement), or, where the defect applies to a part of the product only,
replacement of the part concerned. However, if replacement of the product or
any part thereof is not proportionate with regard to the nature of the defect,
especially if the defect can be removed without undue delay, the customer has
the right to have the defect removed free of charge.
If the noted defect is not removable, or if the customer becomes entitled to
the replacement of the product or a part thereof, yet the replacement is not
possible, for example, due to the product having been sold out, the customer
has the right to return the product (withdrawal from the contract).
The customer shall have the right to a new product (replacement) or to
replacement of a part of the product even if the defect can be removed,
provided they cannot properly use the product due to repeated occurrence of
the defect or due to a high number of such defects. In such a case, the
customer also has the right to return the product (by withdrawing from the
contract).
If the product is not returned (the customer does not withdraw from the
contract), or if the customer does not apply the right to a new defect-free
product (replacement), to replacement of a part thereof, or to repair the
product, they may request a reasonable discount. The customer also has a right
to a reasonable discount if a new defect-free product cannot be supplied to
them, or if a product part cannot be replaced or the product repaired unless
the situation is remedied within a reasonable time limit, or if remedying the
situation would create major discomfort on the part of the customer.
The seller-authorized service center or a staff member authorized by them must
decide about each complaint immediately or within three business days in
complicated cases. This term does not include a reasonable period of time,
depending on the type of product concerned, required for the defect to be
assessed by an expert. A complaint, including defect removal, must be dealt
with without any undue delay, yet no later than within 30 calendar days of the
complaint fi ling date, unless the seller and the customer agree on a later
deadline.
On returning the product (withdrawing from the contract) the customer must
return any accessories and documents supplied along with the product.
The customer does not have the right to keep the defective parts and
components of the product replaced as part of a repair of the product.
This shall be without prejudice to any other rights the customer may have in
relation to the purchase of the product.
Remark: Complaints against products damaged in transport are governed by
the carrier’s complaints procedure.
Manufacturer
Jindřich Valenta – ELKO Valenta
Vysokomýtská 1800, 565 01 Choceň
Czech Republic
tel.: +420 465 471 433
fax +420 465 473 304
Company ID No. 13216660
email: servis@my-concept.cz
www: www.my-concept.com
Product data
Model:
Production number:
Date of purchase:| Seal and signature of vendor:
References
- Concept – chytře vymyšleno pro život
- Domena Concept.pl jest na sprzedaż - SklepDomeny.pl
- Luxury Architecture, Concept Architects, Bratislava
- Concept
- Online software pre autoservis | servis.sk
- Tech.sk | Všetko o informačných technológiáchTech.sk | Magazín o internete a technológiách
- Concept
- Concept – chytře vymyšleno pro život
- Concept innowacje w Twoim życiu!
- www.my-concept.sk | vymyslené pre život
- Verners
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>