GravaStar Mars Pro Bluetooth Speaker User Manual

GravaStar Mars Pro Bluetooth Speaker

Gravastar Mars Pro Bluetooth Speaker

A two-way speaker system design with a passive bass radiator to create big sound in a small enclosure. Using OSP 4 ways, digital crossover independently compensates and tunes the Low Bass, Mid Bass, Mid, and Hig~Frequency to ensure clear sound separation, balanced tonality, and accurate sound reproduction that the musician intended you to listen and enjoy.

Main Features

Play Music with Bluetooth: Bluetooth 5.0, lower power consumption, longer Bluetooth transmission distance. Get away from the shacl<Jes of wired transmission, enjoy music anytime and anywhere

How To Use Gravastar Mars Pro

Bluetooth

Connect
Single Click “ ” “Ready to pair” to search and connect
Disconnect Bluetooth
CIiek the • • button to disconnect, or select from the Bluetooth list on the device”Gravastar Mars Pro” and select disconnect
TWS Net Connecting
Press and hold the Bluetooth buttons on both speakers for 3 seconds, and the Bluetooth indicator flashes rapidly. Single-click the Bluetooth button on the main speaker(the indicator light ff ashes once). then Double click the Bluetooth button on the slave speaker (the indicator light flashes twice).The 2 speakers will start TWS pairing. After the TWS Is successful. the main speaker( s Bluetooth light flashes, Iha indicator of slave speaker is always on, and says “Network-connected”
Disconnect the Network
Double click any Bluetooth button ., * .,to disconnect the networ1<ing (the Bluetooth indicator Is flashing), and you will hear “Networlc disconnected, Ready to pair

1. Reset: Press simultaneously at the same time
2. Delete the Bluetooth record:  Press simultaneously 5 seconds and it will say “Bluetooth connection deleted”

Note

Please charge lithium batteries at least once a month to prevent excessive battery discharge and shorten battery life. Improper battery replacement will cause expk>sion risk. Users are prohibited to disassemble or replace the battery by themselves! If the speaker is not used for a long time, the l lithium battery will become a dormant state, and it will take longer to recharge to activate It. (Before the lithium battery is fully activated, the speaker may not tum on normal y due to low voltage or the sound performance wil be unstable, which is a normal phenomenon).

FEATURES

Important Safety Information

• Before using Gravastar Mars Pro, you must confirm and comply with the folowing safety operating regulations:
• Re.ad and understand all safety guidefnes
• You must use a power adapter with a slable output of 5V
• Please turn off in time when not In use to extend battery Ufe
• Do not expose this product to rain, moisture. dripping or splashing with any liquid
• Do not let this product close to the heat source, do not bake or blow dry at high temperature
• Do not let this product fal or be hit hard

Product Specifications

• Bluotooth version: Bluetooth 5,0
• Battery capacity: 2000mAh x 4
• Playing time: 15H
• Input: SV
• Power: 20W
• Connection dislanca: 1 OM
• Frequency Range Bluetooth: 2402-2480MHt
• Transmit Power ( EIRP) Bluetooth: 3.24dBm

[ DIY ACCESSORIES]
Upper shel handle x 2,Bullet box bracket x 1,Bullot box x 1,Shield connector nx 1,Shield x 1,Shield magnetic cover x 1,Rotating shaft connection ring x 1, nGatfing gun x 1,Machlne gun cover x 1,Phllips screw x4,Short hex socket screw x 4,Long hexagon socket Sa’&W x 2 n Bundled with the package: Phalips screwdriver x 1, hexagon socket screw nconex2

HOW TO INSTALL

Install the upper shell of the speaker

• Align the left and right handles with the holes of the upper shell, and tighten them with Phillips screws from the inside of the shell.
• Install the assembled upper shell of the speaker as shown in the picture

Install bullet box

•  Align the bullet box with the  bracket, press, and insert
• As shown in the picture, the bulet box installation is complete.

Install shield

• * Align the bullet box with the bracket. press and insert

• • Install the shield to the right side of the speaker with hexagonal screws.
    • The tightness of the screw can be adjusted according to personal preference
    • install the shield magnetic cover to the position as shown in the picture Fasten the shield magnetical y at the position shown in the picture.

Install Gatling gun

• * Splice the connecting ring of the shaft and the Gating gun together, and install it to the left side of the speaker with a screw. The tightness of the screw can be adjusted according to personal preference.

  • Tear off the rubber seal inside the cover of the Gading gun and stick It to the position as shown in the figure.
  • Insert the A-end of the bullet chain into the buckle position of the Gatling gun as shown in the picture (pay attention to distinguish the positive and negative directions, and
  • It cannot be buckled in the wrong direction)
  • insert the B end or the Bul et bar into the bayonet position as shown in the picture (no need to distinguish the direction)

What’s in the box

Note: When charging the speaker and playing music at the above 70%, the battery will be activated the NTC 0’l8f1leating protection and stop charging. The battery will automatically resume charging after the heat  drops

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>