TEXAS 340TG Lilli Gasoline Walk-Behind Tiller User Manual

User manual
Lilli
340TG – 345TG – 360TG – 365TG

Texas A/S – Knullen 22 – DK-5260 Odense S – Denmark
Tel. +45 6395 5555 – www.texas.dk – post@texas.dk
Version 23.1

Illustrations

Warning symbols

| | | |
---|---|---|---|---
Warning: Pay attention to rotating blades!| Please read the user
manual carefully before
operating the machine.| Always wear eye and ear
protection.| Wear safety gloves.| Wear nonskid safety footwear.

Congratulations on purchasing your new tiller. Please read this instruction manual carefully, especially the safety warnings marked with the symbol:

Spare parts
Spare part drawings for the specific product can be found on our website www.texas.dk
If you find the part numbers yourself, this will facilitate more rapid service.
For purchase of spare parts, please contact your dealer.
You will find a list of dealers on the Texas website.

Safety precautions

Setup
Do not put hands or feet near or under rotating parts.
Read this manual carefully. Make sure that you are familiar with the different controls, settings and handles of the equipment.
Know how to stop the unit and ensure that you are familiar with emergency stop.
Never allow children or people unfamiliar with these instructions to use the machine. Note, that local regulations can restrict the age of the operator.
If you feel unwell, tired, or have consumed alcohol or drugs, do not operate the machine.
Always inspect the machine before usage Ensure that no parts are worn or damaged.
Replace worn-out or damaged elements and bolts in sets to preserve balance.
The operator of the machine is responsible for people’s safety.
Never use the machine near children or animals.
The operator of the machine is held liable for any accidents or hazards to other people and their property.
Thoroughly inspect the area, where the equipment is to be used, if necessary, remove any foreign objects.
Do not refuel gasoline indoors or while the engine is running.
Spilled gasoline is extremely flammable; never refuel while the engine is still hot.
Wipe off any spilled gasoline before starting the engine.
It may cause a fire or explosion!
Beware of hazards, while working on difficult soil hence; extremely stony or hard soil.
Boots with non-slip soles with steel jacket is required.
Avoid loose-fitting clothes.

Operation

Always start the engine from safety zone.
Do not leave the safety zone while operating the machine, if it is necessary to leave the safety zone, turn off the engine before leaving the zone.
After striking a foreign object, stop the engine immediately, remove the spark plug cap and inspect the machine thoroughly for damage. Repair the damage before continuing
If the machine should start to vibrate abnormally, stop the engine and check immediately for the cause.
Vibration is generally a warning of damage.
Always disengage the levers, turn off the engine, and remove the spark plug, when the unit is left unattended.
Always turn off the engine and ensure that all moving parts have come to a complete stop before making any repairs, adjustments, or inspections.
Exercise extreme caution when operating on slopes.
Never operate the machine at a fast pace.
Do not overload machine capacity by attempting to work at too fast a rate.
Do not carry passengers.
Pay attention, while the machine is in reverse.
Never allow any bystanders in front of unit.
Always disengage the blades, if not in use.
Only operate the machine at daylight or in fully illuminated areas
Ensure a stable foothold and always keep a firm hold on the handles. Always walk, never run.
Do not operate the equipment when barefoot or wearing sandals.
Exercise extreme caution when changing direction on slopes
By rear tillers, ensure that the blades are protected by safety shield, only the part of the blades that works into the soil must be free.
Never attempt to make any adjustments, while the engine is running.
Use extreme caution when reversing or pulling the machine backwards
Never operate the engine indoor or in areas with low ventilation. The exhaustion from the engine contains carbon monoxide. Failure to observe could result in permanent injury or death.

Gasoline safety

Use extreme care in handling gasoline. Gasoline is extremely flammable, and the fumes are explosive.
Serious personal injury can occur, when gasoline is spilled on yourself or your clothes. Rinse your skin and change clothes immediately!
Use only an approved gasoline container. Do not use soft drink bottle or similar!
Extinguish all cigarettes, cigars, pipes and other sources of ignition.
Never refuel your machine indoors.
Let the engine cool down before refilling
Never fill the fuel tank to more than 2.5 cm below bottom of filler in order to provide space for fuel to expansion.
After refueling, ensure that the cap tighten securely.
Never use the lock-function on the gasoline gun, when refueling.
Do not smoke while refueling.
Never refuel inside a building or where gasoline fumes may get in contact with an ignition source.
Keep gasoline and engine away from appliance, pilot lights, barbecues, electric appliances, power tools, etc.
If the fuel tank has to be drained, this shall be done outdoors

Maintenance and storage

The engine shall be stopped when carrying out maintenance and cleaning operations, when changing tools and when being transported by means other than under its own power.
Check regularly that all bolts and nuts are tightened. Retighten if necessary.
The engine must be completely cooled before storing indoors or covered.
If the machine unused for a period of time, please refer to the instructions in this manual.
Maintain or replace safety and instruction labels, as necessary.
Only use original spare parts or accessories. If not original parts or accessories is used, the liability is no longer applied.
Replace faulty silencers.

Miscellaneous

The gears are delivered pre-greased. However, always ensure they are well greased before each use.
The motor is not pre-filled with oil.
Factory-fitted control devices, such as the handlemounted clutch cable, must not be removed or exposed.
Only drain the fuel tank outdoors. Gasoline is extremely flammable, and the fumes are explosive.
Ensure that the machine is properly secured when transported on a flatbed etc.
Reduce the throttle during engine shutdown and close the fuel valve.
Due to vibrations, it is recommended to take a break for every 30 minuttes use to avoid fatique in your arms.

Assembly

Please follow the steps in figure:
(Actual model may vary from the illustration shown)

1. Box content
   A. Tiller with blades
   B. Upper handlebar
   C. Clutch handle
   D. Lower handlebars
   E. Depth skid/support wheels
   F. Throttle control (Lilli 340/360)
   G. Panel (Lilli 345/365)
   H. Side guards (Lilli 360/365)
   I. Extension blades (Lilli 360/365)

2. Fit the lower handlebar section. Use the supplied mountings and bolts. You can choose between 2 different heights of handlebar.

3. Fit the upper handle. Use the supplied assembly kit as shown.

4. Mount the clutch handle and throttle control as shown on the picture. Only Lilli 340/360.

5. Mount the clutch handle, panel, and throttle control as shown on the picture. Only Lilli 345/365.

6. Mount the side guards using the bolts and nuts supplied. Note the side guard must go under the body frame.

7. Mount the extension blades using the cotter bolts and pins. Only Lilli 360/365.

8. Mount the support wheels with the cotter bolt and pin.

9. The support wheels can be turned, so it works as a depth skid. Depth can be adjusted.

Fill the engine with oil. See changing the oil section for more details.

Clothing

When using the machine, wear close-fitting work clothes, hard-wearing work gloves, ear defenders, and non-slip boots with steel toecaps.

Operating the tiller

Ensure the machine is placed on a level surface with the support wheels lowered prior to start.
Remove all foreign objects from the work area before using the machine. Stones, glass, branches, and similar items may damage the tiller. Also, check the bolts on the tiller are tightened.
Start the motor as per the instructions below. Stand clear of the machine’s moving parts.
Never attempt to move the machine in any way other than intended for normal use while the motor is running.

The tiller is designed for use in vegetable gardens and flowerbeds. Ensure that you are familiar with these instructions before operating the machine, in particular, the motor start and stop procedures.
Fig 10: To use the black clutch handle the red control stick (A) must first be activated. By tilting the control stick to the right or left side and then activate the black handle lever, the tiller will move forward or backwards.
Pay attention while reversing. It is important that the area is cleared, for any obstacle before reversing. Never reverse the tiller against a wall, tree, or any other fixed obstacle.
Only model Lilli 345 and Lilli 365 have reverse gear.

Operation zone

While the machine is being operated and the motor is running, do not leave the operation zone marked Fig. 12.
If it is necessary to leave the operation zone, for example, to attach an accessory, first stop the engine.
It is normally necessary to drive the tiller over a section of earth 2-3 times from different directions. Do not till very wet soil, as clods of earth will form that are difficult to break up.

Adjusting the wheel/ depth skid

Fig. 8: Use the support wheels for transportation.
Fig. 9. The depth skid can be set in different depths. The deeper it extends into the soil, the deeper the tilling blades will work and the slower the machine will advance. Setting the correct tilling depth will significantly reduce the effort required. The depth skid should always be adjusted to suit
the ground conditions. We recommend testing several depths to see which works best.

Lubrication of gearbox

The gearbox is permanently lubricated at the factory, never open the gearbox.

Starting and stopping the engine

Remember: Always check the oil level prior to use!
The oil level must always be between the min. and max. Mark on the dipstick. Always use SAE-30 oil (0,45 L.). Use only unleaded E5 gasoline. Never over-fill the gas tank.
Warning: Stay out of dashed zone, while starting the engine! Always start the engine from dotted operation zone.
See Fig. 13.

Starting the engine

1. Set the throttle control on the handle to max. Fig. 11/14

2. Position the choke at max. Move the choke lever fully to the left. Fig. 15.
   The choke is not required if the motor is hot.

3. Pull the start cord to start the motor. Always feed the start cord back into the motor by hand. Fig. 16.

4. When the motor is started, set the choke to minimum (fully to the right) Reduce the throttle slightly.

Stopping the engine

1. Set the throttle control to “low” and let the motor run for approx. 30 seconds.
2. When the motor idles, set the throttle control to full stop.
   Vibrations may travel up into the handle during use. We, therefore, recommend taking a break every 30 minuttes.

Cleaning the tiller

The tiller should be cleaned after use. Use a garden hose to wash off soil and dirt. Remove any grass, etc. from the rotor shaft. The chassis number should only be cleaned with a damp cloth to avoid unnecessary wear. Avoid using a high-pressure washer during cleaning.

Changing the oil

The oil should initially be changed after the first 5 hours of use, and thereafter once per year.

1. Let the motor run for 5 minutes to heat up the oil. This allows the oil to run more freely and makes for a more complete oil change.
2. After 5 minutes, stop the motor. Remove the spark plug cap. Drain the oil by unscrewing the sump plug. Remember to drain the oil into a container of sufficient capacity. NB: The motor must not be tipped backwards more than 45 degrees.
3. Screw the sump plug back in and pour new oil into the motor. Do this by removing the oil cap and pouring in the recommended quantity of oil.
4. Refit the spark plug cap.

Alternatively, use an oil extractor kit.

1. Suck the oil up through the oil filler hole using the syringe. Use the hose to reach the sump.
2. Transfer the used oil to the container.
3. Fill the engine with new SAE-30 oil (0,45 l.).
4. Always check that the oil level is visible and to edge of the fill hole. Fig. 17.

Remember to dispose of used oil in a safe way.
Oil and oil extractor kit are not included

Air filter maintenance

Please inspect and clean the air filter on a regular basis. If the filter has not been cleaned for a longer period, this will have influence on the engines power take-off and the exhaustion.

1. Clean around the air filter before being opened.
2. Loosen the nut and remove cover.
3. Now carefully remove the air filter element.
4. Inspect and remove the dust from the air filter by tapping the element easily a few times. Replace the air filter if it is very dirty.
5. Clean the base and cover.
6. Reattach the air filter element, cover, and fasten the nut.
7. Please check that all parts are assembled correctly

IMPORTANT: Under no circumstances must oil or water be applied on the air filter!

Spark plug maintenance

• Remove the spark plug cap.
• Brush away any dirt and deposit of the spark plug.
• Loosen the spark plug using a spark plug socket.
• Check the insulation is intact.
• Clean the spark plug using a wire brush.
• Measure the electrode gap 0.7–0.8 mm. Avoid damaging the electrode.
• If it is damaged, replace it with a new one.
• Refit the spark plug.
• Refit the spark plug cap.

Storage

• If the machine is likely to be stored unused for prolonged periods, follow the instructions below. This will ensure longer machine lifetime.
• Use a garden hose to wash off soil and dirt. Remove any grass, etc. from the rotor shaft. The chassis number should only be cleaned with a damp cloth to avoid unnecessary wear. Avoid using a high-pressure washer during cleaning.
• Wipe the tiller with a damp cloth so that all surfaces are clean. Wipe the surfaces down with an oily cloth to prevent rust.
• Always store the machine in a dry, clean location.

Troubleshooting

The motor will not start

1. Check the fuel control is set correctly.
2. Check the spark plug.
3. Check there is fresh gas in the tank.
4. See separate motor instructions for further troubleshooting.

The motor is not running smoothly

1. Ensure the throttle control is not set to max.
2. Check there is fresh gas in the tank.

The blades will not rotate

1. Check for stones lodged between the blades.
2. Release any stones by removing the blades.
3. Check the cables are in good working order and fitted correctly.
4. Check the belt is in good working order and fitted correctly.
5. Ensure the belt tensioner is adjusted correctly.

The blades will not stop

1. Stop the engine and contact your dealer.

Noise, vibration, and precautionary measures

1. Long-term exposure to noise levels exceeding 85 dB (A) are damaging. Always use ear defenders when the machine is being used.
2. Reduce the running speed of the motor to reduce vibration and noise levels.
3. To reduce noise levels further, only use the machine in an open environment.
4. Vibrations can be reduced further by holding the handle firmly.
5. To avoid disturbing others, the machine should only be used during the daytime.
6. Always wear close-fitting work clothes, hard-wearing work gloves, ear defenders and non-slip boots with steel toecaps.
7. Take a 30-minute break every 2 working hours.
8. A worn belt must be replaced/ serviced by an authorized dealer

Warranty terms and conditions

The warranty period is 2 years for private end users in EU countries.
Products sold for commercial use, only have a warranty period of 1 year.
The warranty covers material and/or fabrication faults.

Restrictions and requirements
Normal wear and replacement of wearing parts are NOT covered by the warranty.
Wearing parts, which are NOT covered for more than 12 months:

• Blades
• Cables
• Belts
• Switches
• Membranes/gaskets
• Spark plugs
• Engine liquids (oil, gasoline)
• Starter cords
• Filters

If you start the engine without adding oil, it will be damaged and cannot be repaired and therefore not covered by the warranty.

The warranty does NOT cover damages/faults caused
by:

• Lack of service and maintenance
• Structural changes
• Exposure to unusual external conditions
• Damages to the bodywork, deck, handles, panels, etc.
• If the machine has been improperly used or overloaded
• Wrong use of oil, gasoline, or other liquid types, which are not recommended in this user manual
• Bad or dirty gasoline, which results in contamination of the fuel system
• Use of unoriginal spare parts.
• Other conditions where Texas cannot be held responsible.

Whether a case is a warranty claim or not is determined in each case by an authorized service center.
Your receipt is your warranty note, why it should always be kept safe.

REMEMBER: The purchase of spare parts as well as any request for warranty repair, art. no. (e.g. 900611XX), year, and serial number should always be informed. It can be found on the CE label on the machine!

• We reserve the right to change the conditions and accept no liability for any misprints

Specifications

Model

Model| Lilli 340TG| Lilli 345TG| Lilli 360TG| Lilli 365TG
Weight (kg)| 33.0| 34.| 35.0| 37.
Forward gears| 1| 1| 1| 1
Reverse gears| –| 1| –| 1
Handlebar| Non-adjustable| Non-adjustable| Non-adjustable| Non-adjustable
Working width| 40 cm| 40 cm| 40-60 cm| 40-60 cm
Working depth| 26 cm| 26 cm| 26 cm| 26 cm
Rotation speed, blades| 130| 130| 130| 130
Type of grease| EP-0| EP-0| EP-0| EP-0
Engine
Model| Texas TG195| Texas TG195D| Texas TG195| Texas TG195D
Capacity| 78.5 CC| 78.5 CC| 78.5 CC| 78.5 CC
Max power| 1.4 kW / 3600 rpm| 1.4 kW / 3600 rpm| 1.4 kW / 3600 rpm| 1.4 kW / 3600 rpm
Sound power level| LWA: 93 dB(A)
LPA: 88.2 dB(A)| LWA: 93 dB(A)
LPA: 88.2 dB(A)| LWA: 93 dB(A)
LpA: 88.2 dB(A)| LWA: 93 dB(A)
LPA: 88.2 dB(A)
Vibration level (left / right handle)| 8.1 m/s2/ 7.4 m/s2| 8.1 m/s2/ 7.4 m/s2| 8.1 m/s2/ 7.4 m/s2| 8.1 m/s2/ 7.4 m/s2

Accessories

EC Declaration of conformity

Manufacturer
Texas Andreas Petersen A/S
Hereby certifies that the following
Gasoline cultivator

Lilli 340TG – Lilli 345TG – Lilli 360TG – Lilli 365TG
Is in compliance with the specifications of the machine directive and subsequent modifications
2006/42/EC – 2014/30/EU – 2000/14/EC amended by 2005/88/EC
Conforms with the following standards

EN709: 1997+A4:2009, EN709+A4/AC:2012, EN14982:2009
LwA: 93 dB(A) LpA: 88.2 dB(A)
Vibrations Ah (left / right handle): 8.1 / 7.4 m/s 2

Serial numbers:
Lilli 340TG 2303023210000 – 2503023299999
Lilli 345TG 2303023310000 – 2503023399999
Lilli 360TG 2303023410000 – 2503023499999
Lilli 365TG 2303023510000 – 2503023599999

Texas Andreas Petersen A/S
Knullen 22 • DK-5260 Odense S 09.05.2022

Johnny Lolk
Managing Director

Responsible for documentation
Johnny Lolk

References

• Salg af havemaskiner - Texas A/S

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>