Levenhuk LP50 Weezer PLUS Weather Station User Manual

: June 5, 2024
: levenhuk

Table of Contents

Base station
Sensor
Interface icons
Levenhuk Wezzer PLUS LP50 Weather Station
Getting started
Specifications
Documents / Resources

Levenhuk Wezzer PLUS LP50Weather Station
User Manual

Levenhuk LP50 Weezer PLUS Weather Station

Base station

SET button
ALARM button
MEM button
CH button
UP button
DOWN button
SNZ/LIGHT button
Wall mount hole
Battery compartment
Table stand (fold-out)
Battery compartment cover

Sensor

Temperature
Humidity
Current channel
LED indicator
Wall mount hole
RESET button
Channel switch (1—3)
Battery
compartment cover
Battery
compartment

Interface icons

Low battery indicator
Alarm
Time/Calendar
Weather forecast
Atmospheric pressure
Climate indication
Indoor temperature
Indoor humidity
Outdoor temperature (sensor 1)
Sensor connection status
Outdoor humidity (sensor 1)
Outdoor temperature (sensor 2)
Outdoor humidity (sensor 2)
Outdoor temperature (sensor 3)
Outdoor humidity (sensor 3)

Levenhuk Wezzer PLUS LP50 Weather Station

The kit includes a base station, 3 sensors, a user manual, and a warranty.
Also required (not included):
2 AAA batteries for each sensor
3 AAA batteries for the base station

Getting started

Base station

Open the battery compartment cover (11) and insert 3 batteries according to the correct polarity. Close the cover.
Wait until the indoor temperature is displayed on the base station. Sensor
Open the battery compartment cover (8). Set the desired channel with the switch.

NOTE! This weather station can be operated with up to 3 remote sensors. Each remote sensor that is to be connected must be operated on a different channel. If only one emote sensor is connected, it should be operated on channel 1.

Insert 2 batteries according to the correct polarity. Close the cover.
To re-establish the sensor connection manually, press RESET using a pin.

Sensor connection

Place the base station and the remote sensor within the effective transmission range. Ensure that the channels are assigned after you set up the power supply for the base station and all the sensors.
If the reception is successful, the display will show the temperature and humidity of the respective outdoor sensor. If the values are not received from a channel, “—” appears on the display. Check the batteries and try it again. Check if there is any source of interference.
When changing batteries, replace the batteries first in the base unit, and then in all the sensors, to re-establish the connection. If an adapter supplies power to any of the devices, briefly disconnect the power to that device when replacing the batteries. If you change the batteries only in one of the devices (for example, in the sensor), the signal may not be received correctly.
The effective range may differ depending on the unit’s position. Due to interference (various remote control devices, etc.), the maximum distance between the base unit and the sensor may be significantly reduced. In such cases, we suggest moving the base unit and sensor a little. Sometimes it is enough to move one of these units a few inches!

** NOTE! Although the sensor is weather resistant, never place it in direct sunlight or in the rain or snow.
Time setting**
Press the SET button and hold it for 3 seconds. The digits that are to be set are flashing. Press UP or DOWN to change the value, and then press SET to continue.
The setting order: Hours > Minutes > Year > Date/Month or Month/Date format > Month > Date > Atmospheric pressure (hPa/mmHg/mb).
Finally, press the SET button to save the settings and exit.
Press SET to check the calendar.
The language and the selected abbreviations for each day of the week are shown in the following table.

Language	Monday	Tuesday	Wednesday	Thursday	Friday	Saturday	Sunda
English, EN	MO	TU	WE	TH	FR	SA	SU

Alarm setting

Press the ALARM button and hold it for 3 seconds. The digits that are to be set are flashing. Press UP or DOWN to change the value, and then press the ALARM button to continue.
The setting order: Hours > Minutes.
Press ALARM to turn the alarm on or off.
Snooze function
When the alarm rings, press SNZ/LIGHT to activate the snooze function. The alarm will sound again in 5 minutes.
Weather
Temperature/humidity

Press the UP button to switch between °C and °F.
When the temperature and humidity values are outside the operating range, the LCD displays the “LL.L” symbol (value below the operating range) or the “HH.H” symbol (value above the operating range).

Weather forecast

Sunny
Partly cloudy
Cloudy
Rainy
Snowy

Climate indication

Levenhuk LP50 Weezer PLUS Weather Station - Weather

The climate indication is a pictorial indication based on indoor air temperature and humidity in an attempt to determine the comfort level.
History record

Press the MEM button to display the MAX./MIN. temperature and humidity.
To clear the history records, press and hold the MEM button for 3 seconds.

Specifications

Base station

Atmospheric pressure, units of measurement| hPa/mmHg/MB
Air humidity, units of measurement| % (RH)
Operating humidity range (indoors)| 1… 99%
Temperature, units of measurement| °F, °C
Operating temperature range (indoors)| -10… +50°C (+14… +122°F)
Time format| 24 hours, 12 hours
Weekday display language| English
Screen| monochrome
Power supply| З ААА batteries (not included)
Dimensions| 148x25x136mm (5.8×0.9×5.3in.)
Wireless sensor| 3 pcs. (included)
Sensor

The manufacturer reserves the right to make changes to the product range and specifications without prior notice.
Care and maintenance

Take the necessary precautions when using the device with children or others who have not read or who do not fully understand these instructions.
Do not try to disassemble the device on your own for any reason. For repairs and cleaning of any kind, please contact your local specialized service center.
Protect the device from sudden impact and excessive mechanical force.
Store the device in a dry, cool place away from hazardous acids and other chemicals, away from heaters, open fires, and other sources of high temperatures.
Operate the device only in a completely dry environment and do not touch the device with wet or damp body parts.
Only use accessories and spare parts for this device that comply with the technical specifications.
Check this device and its cables and connections for any possible damage before use.
Never attempt to operate a damaged device or a device with damaged electrical parts! Damaged parts must be replaced immediately by an authorized service agent.
If a part of the device or battery is swallowed, seek medical attention immediately.
Children should use the device under adult supervision only.

Battery safety instructions
Always purchase the correct size and grade of battery most suitable for the intended use. Always replace the whole set of batteries at one time; take care not to mix old and new ones or batteries of different types. Clean the battery contacts and also those of the device prior to battery installation. Make sure the batteries are installed correctly with regard to polarity (+ and -). Remove batteries from equipment that is not to be used for an extended period of time. Remove used batteries promptly. Never short-circuit batteries s this may lead to high temperatures, leakage, or explosion. Never heat batteries in order to revive them. Do not disassemble batteries. Remember to switch off devices fter use. Keep batteries out of the reach of children, to avoid the risk of ingestion, suffocation, or poisoning. Utilize used batteries as prescribed by your country’s laws.
Levenhuk International Lifetime Warranty
All Levenhuk telescopes, microscopes, binoculars, and other optical products, except for their accessories, carry a lifetime warranty against defects in materials and workmanship. lifetime warranty is a guarantee of the lifetime of the product on the market. All Levenhuk accessories are warranted to be free of defects in materials and workmanship for six months from the purchase date. The warranty entitles you to the free repair or replacement of the Levenhuk product in any country where a Levenhuk office is located if all the warranty conditions are met.
For further details, please visit: www.levenhuk.com/warranty
If warranty problems arise, or if you need assistance in using your product, contact the local Levenhuk branch.
The original Levenhuk cleaning accessories

Levenhuk Cleaning Pen LP10

Removes dust with a brush
The soft tip is treated with a special cleaning fluid that removes greasy stains
Does not damage the optical coatings of the lenses
Leaves no smudges or stains

Levenhuk Inc. (USA): 928 E 124th Ave. Ste D, Tampa, FL 33612, USA,
+1-813-468-3001, contact_us@levenhuk.com
Levenhuk Optics s.r.o. (Europe): V Chotejně 700/7, 102 00 Prague 102,
Czech Republic, +420 737-004-919,sales-info@levenhuk.cz
Levenhuk ® is a registered trademark of Levenhuk, Inc.
© 2006—2022 Levenhuk, Inc. All rights reserved.
www.levenhuk.com
20220421