TEXAS BMZ 5800 Arboriculture Vine Trimmer User Manual

TEXAS BMZ 5800 Arboriculture Vine Trimmer

IMPORTANT  INSTR UCTION

How to read the manual
Please read this instruction manual carefully, especially the safety warnings marked with the symbol: When using the product, the safety instructions must be closely followed. Read this manual carefully before starting the machine. Make sure that you know how to stop and switch off the engine in case of accident. All instructions regarding safety and maintenance of the machine are for your own safety. The warnings, precautions and instructions given in this manual, cannot cover all situations that the product can be placed in. The user must therefore present common sense and caution when using the product.

WARNING AND SYMBOL

Safety in the work area

•  Only use the product in clean and well lit areas
•  Do not use the product in areas with explosive danger or where there is flammable fluids, gas or dust present.
•  The person that uses the machine is responsible to other persons in the work area. Never use the machine when others, especially children or animals are near.
•  This machine is an electric product. It is therefore important, that it ever comes in contact with water or is used in wet surroundings.

Use and maintenance of the product

•  This machine must not be used for other work than as described in this manual.
•  Only use original spare parts. Mounting of nonapproved parts may lead to increased risk and are therefore not legal. Any liability is renounced for accidents or other damage that has happened due to the use of unauthorised parts.
•  Before using the machine, the dealer or other qualified person should instruct you in the use of the machine.
•  Minors may not work the machine.
•  The machine may only be lent to people who know how to work the machine. This manual should follow the machine under all circumstances.
•  The machine may only be used by persons who are rested, well and fit. If the work is tiring, frequent brakes should be made. Do not use the machine under influence of alcohol.
•  Always check before start, that all bolts and nuts are tigthened.
•  Always wear eye protection when using the machine.
•  Keep the trimmer head clean and free from wrapped grass or weed.
•  Keep children and other persons at a distance of at least 5 metres from the work area.
•  The battery should always be removed when:
•  maintenance is made.
•  the machine is left unattended
• During transport, the main switch must be switched off.

**Identification of the machine and components

**

1.  3-tooth blade
2.  Cutting guard
3.  Shaft
4. P-handle
5.  Shoulder strap mount
6.  Safety switch
7.  Trigger switch
8.  Trimmer head
9.  Main switch
10.  Power indicator light
11.  Speed button (normal – turbo)
12.  Speed light
13.  Shoulder strap
14.  User manual
15.  Allen key
16.  Wrench
17.  Screwdriver
18.  Battery (not included)
19. Charger (not included)
20. Polesaw
21.  Pole-hedge trimmer

Unpacking and assembly

•  Unpack all parts and lay them on a flat, stable surface.
•  Remove all packing materials and shipping devices, if applicable.
•  Make sure the delivery contents are complete and free of any damage. If you find that parts are missing or show damage do not use the product but contact your dealer.
• Using an incomplete or damaged product represents a hazard to people and property.
•  Ensure that you have all the accessories and tools needed for assembly and operation. This also includes suitable personal protective equipment.
•  Plug in the battery, by pushing it down until you hear a click
•  Remove the battery by push down the battery lock buttons and pull up.

Mounting of the P-handle

• Loosen the 2 screws on the handlebracket
•  Mount the handle on the shaft and adjust position
•  Tighten the 2 screws again, so the handle is fixed

Mounting of the guard.

•  Loosen and remove the 2 screws from the guard
•  Mount the guard under the shaft
•  Tighten the the 2 screws again so the guard is fixed

Place the guard on the motor house and fix it with the 2 included screws. The knife on the side will shorten the nylon line if it becomes too long. This guard is intended to prevent loose objects from being thrown towards the operator. The guard also protects the operator from accidental contact with the trimmer head. Check that the guard is undamaged and not cracked. Replace the guard if it has been exposed to impact or is cracked.

Mounting of shaft.

•  Loosen the wing knob (A)
•  Remove the end cap from the attachment shaft
•  Pull out the shaft-release knob (B)
•  Push in the attachment shaft (C) until you hear a clear “click” sound”.
•  Tighten the wing knob (A)

Mounting of the blade

•  Fit the Allen key in the hole of the gear to lock the gear in place.
•  Fit the washer blade, washer and the holder onto the axle.
•  Fit the nut. Fasten tightly anticlockwise. Make sure the blade is securely fastened. Ensure that the blade is tightly fastened

Mounting of trimmer head.

•  Fit the Allen key in the hole of the gear to lock the gear in place.
•  Fit the washer.
•  Mount the trimmer head onto the shaft, turn it in place and make sure it is securely fastened.

Mounting of polesaw

•  Attach the polesaw to the middle tube and fasten.
•  Mount the guide bar and chain, Pay attention that the chain is facing the right way.
•  To loosen/tighten the chain, the adjustment screw in front of the saw is used. It is recommended to check and add chain oil every 30-45 min. See the “Maintenance” section.

Mounting of pole-hedge trimmer

•  Remove the protection cap from the hedge trimmer unit.
•  Attached the tube into the hedge trimmer. See the small hole on tube to know which direction goes in. Tighten the screw.
•  Attach the hedge trimmer to the engine unit and fasten.

The hedge trimmer tube can be placed in a transport angle. When the hedge trimmer is being used, the tube must be turned back in work position and the screw must always be tighten again before use. The blades must be kept lubricated to prevent friction and to extend durability.

Battery

This product is delivered without battery and charger. It is sold separately. Warning: Do not try to disassemble, short circuit or put it to extreme heat or fire, as it can cause serious inquiry and permanent damage to the battery! The battery pack is only about 30% charged when delivered.

Charging

•  Only use the original charger with art. no. 90070054
•  Before the battery is being used the first time, it is recommended to fully charge it first.

Charger

• A full charge takes around 60 min for 2.0 Ah batteri and 120 min for 4.0 Ah battery.
•  Only use the original charger, which matches this product.
•  Do not try to charge other type of batteries in the charger, other than the original batteries with art. no. 90070051 (2.0 Ah) or 90070052 (4.0 Ah).
•  Keep the charger in a dry and warm environment (10-25 degrees C) and only use it indoor. It should be connected to a normal 230V AC socket.
• Before the battery is being used the first time, it is recommended to charge it fully.
•  The surface of the battery can become warm during charging. This is normal.
•  Do not cover battery or charger during charging. Allow free ventilation of air.

Insert the battery into the slots of the charger and slide it into place until it locks. There are 4 lights on the charger indicating the status and state of charge of the battery

Important:

The charger will stop, when the battery is full. However, it is not recommended to leave the battery in charger for more than 24 hours. It is recommended to drain the battery completely and fully charge it whenever possible, as it can increase the health of the battery. But partial charge will not damage the battery. To remove the battery from the charger, hold the button down and pull the battery out. Before winter storage, the battery should be fully charged and kept warm at 10-20 degrees C. Charge it every 3 months. Make sure to keep ventilation holes clean and free from dirt. Store the charger indoor between 5-25 degrees C.

Use

• Before use, make sure that the battery is fitted properly with the battery lock in place.
• To start the machine first press the main switch (A), so the power indicator lights green. Then hold the safety switch (B) and activate the trigger switch (C).
• Stop the machine by releasing the trigger switch (C).
• Stop ved at slippe aktiveringsknappen (C). Always remove the battery, when the machine is not being used.
• Press the speed button (D) to choose between normal speed and turbo speed.
• Turbo speed will consume the power faster, and should only be used when neccesary. Automatic switch off function
• The machine is equipped with a switch off function that deactivated the machine if not used within approx. 60 seconds. The green power indicator light will switch off too.
• Press the main switch (1) to restart.

Important when using:

•  When the engine is stopped the rotating blade must be held in grass or bush until it holds still.
•  Always hold the machine with both hands.
•  The machine must not be used if the safety guard is not correctly fitted and in mint condition.
•  Always stop the engine before attempting to remove objects that may have stuck on the blade.
•  Never touch or try to stop the blade while it is still spinning.
•  A rotating blade may cause damage, as it continues to spin after the engine has stopped or the gas has been turned off. Always be in control of the tool until the blade has stopped spinning.
•  Always make sure that the blade is mounted securely and correctly before every time is used.
•  Only use a sharp blade. Replace blades that are worn or damaged.
• Only use original spare parts.
• Only use the blade for weeds, grass and similar.
•  Throw back is something that may occur when the rotating blade gets into contact with something, it cannot cut. This contact may have the effect, which the blade stops for a moment, and suddenly the tool is thrown away from the hard object that was hit. This reaction may be so violent that the user loses control of the tool. Throw back may occur without warning if the blade is stuck, loses speed or impeded. This is most likely in areas where it is difficult to see the material that is being cut.
•  The harness must always be used and adjusted to fit in the correct manner.
• Keep a firm grip on both handles while the blade is running. Keep the blade away from your body and below your waist.
•  See Fig. 7 for working direction for trimmer head and with blade.

Clothing
When using the machine, wear tight-fitting work clothes, strong working gloves, hearing protectors, safety goggles and boots with non-skid soles

Tips and advice

Trimming.
Hold the trimmer head just above the ground at an angle. It is the end of the line that does the work. Let the line work at its own pace. Never press the line into the area to be cut.

Cutting.

The trimmer is ideal for cutting grass that is difficult to reach using a normal lawn mower. Keep the line parallel to the ground when cutting. Avoid pressing the trimmer head against the ground as this can ruin the lawn and damage the tool. Do not allow the trimmer head to constantly come into contact with the ground during normal cutting, as this can cause damage and wear to the trimmer head. Only bump the trimmer head against the ground to release more nylon line

Sweeping.

The fan effect of the rotating line can be used for quick and easy clearing up. Hold the line parallel to and above the area to be swept and move the trimmer head from right to left and opposite. When cutting and sweeping you should use full throttle to obtain the best results.

3-tooth blade.
It is used to cut through dense vegetation,

Rewinding the spool

Before any service and maintenance is done, the power must be disconnected, it means the battery removed from the tool. See Fig. 9 The spool is supplied with the nylon line on it. When need to rewind the spool with new nylon line, follow these steps:

• Press each side of cord housing. Remove lid.
• Remove roll by pulling. Allow spring to remain on spool. Remove any cord residue. Take 3-4 m of cord (2.4 mm) and double it up.
•  Insert both ends into the 2 holes on the roll. Wind cord onto roll in direction of arrow. Avoid twisting cord. When twine is fully on roll, cut and insert the two cut ends through the guide holes.
•  Assemble cord housing in reverse order, starting with spring. Place cord in cord housing holes.
•  Re-place cover. Check cover is secure.

Always ensure trimmer head is secured tightly. NEVER OVERFILL THE SPOOL WITH LINE!

Maintenance

• Before any service and maintenance is done, the power must be disconnected, it means the battery removed from the tool.
•  Remove the battery before you clean and store the machine.
•  Clean the housing and other parts with a soft brush and a moist cloth. Never use aggressive cleansers or solvents.
• Prevent water from getting into the machine.

Lubrication of brushcutter gear

The gear is lubricated from the factory, but for every 30-hour operation grease must be refilled. Top up with grease type: EP-0 using a grease gun (not included) on the lubrication nipple.

Lubrication of saw chain

•  Place saw on a flat surface
•  Remove the lid.
• Add chain oil in the pruner container (top up).

Depending on the conditions you should add chain oil for every 30-45 minutes of use, so check oil level often. If the polesaw is used without chain oil, the chain will be damaged.

Lubrication of hedge trimmer gear

The gearbox is lubricated from the factory, but for every 30-hour operation Grease must be refilled. Top up with grease type: EP-0 using a grease gun (not included) on
the lubrication nipple. See fig. 10 The blades must be kept lubricated to prevent friction and to extend the durability.

Storage

Store the trimmer dry and unavailable for children. It is recommended not to let it rest on the trimmer head. Hang it on a wall in the handle.

Specifications

Warranty terms and conditions

The warranty period is 2 years for private end users in EU countries. Products sold for commercial use, only have a warranty period of 1 year. The warranty covers material and/or fabrication faults.

Restrictions and requirements

Normal wear and replacement of wearing parts are NOT covered by the warranty. Wearing parts, which are NOT covered for more than 12 months:

•  Trimmer head and spool
•  Nylon line, blade
•  Saw chain and guide bar
•  Hedge trimmer blade
•  Cutting guard and knife
• Battery: If the battery is not stored correct (frostfree and recharged every 3 months), the durability is only guaranteed for 6 months.
• The warranty does NOT cover damages/faults caused by:
•  Lack of service and maintenance
•  Structural changes
• Exposure to unusual external conditions
•  If the machine has been improperly used or overloaded
•  Use of unoriginal spare parts.
•  Other conditions where Texas cannot be held responsible.
• Whether a case is a warranty claim or not is determined in each case by an authorized service center. Your receipt is your warranty note, why it should always be kept safe.

REMEMBER:

The purchase of spare parts, as well as any request for warranty repair, art. number (e.g. 900700XX), year and serial number, should always be informed.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>