MEEC TOOLS 230 V/25 W GLUE GUN Instructions

MEEC TOOLS 230 V/25 W GLUE GUN Instructions

Important! Read the user instructions carefully before use. Save them for future reference. (Translation of the original instructions).

SAFETY INSTRUCTIONS

WORK AREA

• Keep the work area clean and well lit. Dark and cluttered work areas increase the risk of accidents and injuries.
• Connect the product to a power point with at least a 10 A fuse. The product should be connected to a separate circuit.
• Never leave the product unattended when switched on.
• Place the product on a level, stable surface. Do not put the product on or near a hot stove, or over other appliances.
• Do not touch hot surfaces. Use the handle.
• Do not allow the power cord to hang over the edge of a table or worktop, or to come in contact with hot surfaces.
• Do not immerse any part of the product in water or any other liquid.
• If an extension cord is used the cross-sectional area of the wires must be dimensioned for the power supply to the product. Check that the mains voltage corresponds to the rated voltage on the type plate.
• If the power cord or plug are damaged they must be replaced by an authorised service center to ensure safe use.
• Pull out the plug before cleaning, before moving the product and when the product is not in use.
• Do not dismantle the product or attempt to modify, or repair it.
• Do not poke any objects into the openings on the product.
• The product is only intended for household use. Do not use the product outdoors.
• This product can be used by children from 8 years and upwards and by persons with physical, sensorial or mental disabilities, or persons who lack experience or knowledge, if they are supervised or receive instructions concerning the safe use of the product and understand the risks involved with its use. Do not allow children to play with the product. Do not allow children to clean or maintain the product without supervision.
• Note that the heater element will still be hot after the product is switched off — risk of burn injury.

IMPORTANT

• It is not possible to remove spots of hotmelt glue from clothes.
• Wear safety glasses.
• Allow the product to cool upright in its holder after use.
• Pull out the plug during long pauses in the work.

SYMBOLS

The following symbols can be of importance for how you should use your power tool. Make sure you understand the symbols and their significance.

Read the instructions.

Approved in accordance with the relevant ELI directives.

This product has a safety class II rating. This means it is fitted with extra or double insulation.

Recycle as electrical waste.

TECHNICAL DATA

Rated voltage: 230 V – 50 Hz
Nominal input power: 25 W
Heating effect: 10-15 g/min
Temperature range: 170 —190°C
Safety class: II
Protection rating:  IP20
Cord length: 1.3 m
Glue stick: 11.2 mm

Glue sticks sold separately in Jula’s department stores and at www.jula.com.

DESCRIPTION

PARTS

1. Opening
2. Power cord
3. Trigger
4. Support
5. Nozzle
   FIG. 1

INTENDED USE

The product is a hotmelt glue gun intended for gluing wood, plastic, foam plastic, textile, tiles and ceramic, etc. The glue can also be used to seal holes and seal joints.
The product is only intended for household use.

HOW TO USE

BEFORE US

1. Avoid skin contact. Avoid all contact with water and liquid and substances containing solvent. Only use glue sticks of the available standard type.
2. Fasten the wire bridge on the product. Insert a glue stick through the opening (1) and push in all the way.
3. Connect the power cord the charging station first and then to a power point. Put the glue gun in the charging station so that the connector on the handle is correctly connected to the connector on the charging station. The power status light in the handle goes on.
4. Allow the glue gun to warm up for about 5 minutes. Remove it from the charging station afterwards by pushing it forwards. (Never try to push it up!)
5. If the work can be carried out more or less stationary the glue gun can be used with the power cord plugged into a power point.
6. Plug the plug on the glue gun into a power point and allow it to warm up for about 5 minutes. Stand the glue gun on its support bridge during short pauses in the work.
   • Replace the glue gun in the charging station for a new charge as soon as the glue begins to become viscous and difficult to feed out.
   • During pauses in the work and after finishing the work, pull out the plug and put the glue gun in the charging station to cool.
   • During long pauses in the work and after finishing the work, pull out the plug and allow the gun to cool upright on its support bridge.

GLUING

• Carefully press the trigger and apply glue to the surfaces of the joint. Join parts within 15 to 20 seconds after applying the glue. Insert new glue sticks when necessary. The glue congeals after about 30 seconds and reaches 90% of its full strength after 1 minute.
• If the glue is applied thicker it takes longer to congeal, and shorter to congeal if applied thinly. Large surfaces should not be glued in one go, but should if possible be divided up into smaller sections.
• Apply the glue in wavy strings. Preheating of the joint surfaces with a hot air gun increases the bonding strength of the glue.
• Allow surplus glue and residue to completely cool before removing.
• Hotmelt glue joints can be separated or corrected by reheating with a hot air gun.
• The supplied long sleeve is intended for gluing joints difficult to reach, and for filling cavities and plugholes etc. The nozzle can only be changed when the glue gun is cold.
• Test temperature sensitive material first, by for example gluing samples.

NOTE:
The product has a built-in magazine to store heat, which enables it to be used cordless for short periods. The magazine is charged in the supplied charging station, which also functions as a parking stand for the product during pauses in the work.

MAINTENANCE AND CLEANING

Pull out the plug before cleaning and maintenance.

• Clean the product casing with a damp cloth and wipe dry. Do not use abrasive or solvent-based detergents.
• Apart from cleaning, the product is practically maintenance-free. Never clean the product by dipping it in water or any other liquid. See also the instructions.

STORAGE

Store the product, accessories and instructions in the original packaging. This ensures that all the information and parts are easily accessible.

Care for the environment!
Recycle discarded product in accordance with local regulations.

JULA AB, BOX 363, SE-532 24 SKARA
2022-01-18
© Jula AB

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>