FeinTech VSP01222 HDMI 2.0 ARC or CEC Pass Splitter 2×2 Instruction Manual
- June 4, 2024
- FeinTech
Table of Contents
FeinTech VSP01222 HDMI 2.0 ARC or CEC Pass Splitter 2×2
Dear customer, Thank you for purchasing this high quality product. For optimal and safe use, please read this manual before commissioning. Please keep the manual as a future reference.
Functions
- HDMI splitter for distribution to 2 HDMI sinks (TV / projector)
- An HDMI output supports ARC (Audio Return Channel). When connected to an ARC/eARC connection on the TV set, the TV sound can be passed through. For example, to an AV receiver which is connected to the HDMI input of the splitter.
- Switchable HDMI input for a second HDMI source
- Automatic scaler for 4K output on a Full HD display
- EDID management with COPY / MIXED / DEFAULT mode
- Supports Ultra-HD up to 4K 60Hz as well as HDR10, HLG-HDR and Dolby Vision
- Supports all sound formats from input to output. In the return channel (HDMI-ARC), audio formats up to Dolby Digital Plus (including Dolby Atmos) are supported.
Note:
It is not useful to operate a soundbar here which has only one HDMI
connection. One HDMI input and one HDMI output are required on the soundbar.
If you change the settings on the TV or splitter, note that it may be
necessary to restart the connected devices. If you do not obtain the desired
output or display, please proceed as follows:
- Switch on the desired EDID mode on the splitter and select the desired HDMI source 1 or 2.
- Disconnect all devices from the power supply for a few seconds, i.e. pull the mains plug.
- Then plug in the power plugs and switch on the devices. In the following order: television, sound system, HDMI splitter, HDMI source
Audio and video formats / EDID modes
The formats are negotiated between the devices. You can influence this via the EDID control (EDID = Extended Display Identification Data, which identifies an HDMI sink).
COPY
With this setting, the HDMI source only detects the HDMI sink at HDMI output 1
and optimises the output format for it. This setting is usually useful if your
main device supports many audio and video formats. In this setting it may be
possible that your second device does not play any sound or picture, because
the format is not supported. If your main device supports HDR / Dolby Vision,
but the second display does not, HDR will be displayed with distorted colours
on the second device.
MIXED
With this setting, your HDMI source delivers a signal that both end devices
can process. This setting can be useful if you use both end devices at the
same time. The lower featured HDMI sink device limits the possible formats.
DEFAULT
In this mode, the HDMI source is signalled that your end devices support
formats up to 4K 60Hz HDR Dolby Vision and 7.1 HD sound formats. The HDMI
source will then output the best possible format. If your device is mute or
produces a black screen, the format is not supported. In this case, select
another mode.
Note : On some HDMI sources, you can manually set the audio and video format and override EDID negotiation.
Automatic scaler
Basically, both end devices receive the same audio and video format. Exception: One display supports 4K, the second display only supports Full-HD and the source delivers 4K. Then the scaler function works in the splitter (except for 4K 60Hz YUV 4:2:2). The Full-HD device thus receives a video signal downsized to 1080p, i.e. 4K / 2160p 60Hz becomes 1080p 60Hz. The HDR mode and audio are not changed. The 4K display maintains the original resolution.
ARC pass
If you use the splitter at the output of an AV receiver, please connect HDMI ARC or eARC of a television to HDMI Output 1. You can then play back the sound from the TV’s internal tuner or smart TV apps via the AV receiver. The volume can be adjusted as usual, HDMI-CEC control is supported. ARC mode must be set on the TV and the AV receiver.
Connections & controls
- Connection for hollow DC plug 5.5/2.1 mm for 5 V power supply
- LED lights up when power supply is active
- HDMI output 1, supporting HDMI-ARC and HDMI-CEC. Connect a television set here.
- HDMI output 2, e.g. for connection to a video projector, monitor, second television
- Pressing once switches between the two HDMI inputs. Double press switches between the 3 EDID modes.
- HDMI input 1 for an HDMI source or the HDMI output of an AV receiver
- LED lights up when input 1 is active. green = EDID copy mode, red = EDID default mode, red and green = EDID mixed mode
- HDMI input 2 for an HDMI source
- LED lights up when input 2 is active. green = EDID copy mode, red = EDID default mode, red and green = EDID mixed mode
Installation and operation
- Connect one or two HDMI signal sources (such as Blu-ray players) to the HDMI inputs. Or connect the HDMI output of an AV amplifier or soundbar.
- Connect two HDMI sinks (e.g. TV and video projector) to the HDMI outputs.
- Connect the mains adapter to the HDMI splitter and plug it into a mains socket. Then switch on one or both end devices (TV / video projector), then the AV receiver and an HDMI source.
- Caution : When inserting and removing the HDMI cables, make sure that the plug contacts are not dirty or damaged. Make the connections without power, and do not switch on the equipment until you have made the connections. Please also make sure that the HDMI cables are of good quality – especially for 4k transmission. We recommend a maximum cable length of 5 m at the inputs and outputs for 4k HDR. If you are using fibre-optic hybrid HDMI cables or other active cables and are experiencing regular dropouts, please select EDID-COPY mode to establish a stable HDMI handshake
Safety
- Please do not cover the housing or power supply, or install the device to avoid overheating.
- Keep away from fire, heat sources, water and moisture.
- Do not place heavy objects on the device or the connection cables.
- Do not open or drill holes in the housing.
- Use only the supplied power adaptor or ensure identical performance data when replacing.
- Use only a soft, dry cloth to clean the surface of the unit. Please do not use aggressive cleaning agents, gasoline or the like.
- If the unit will not be used for a longer period of time, please unplug it from the mains.
Service
The device must be inspected by qualified personnel in the following cases.
- Objects or liquids have penetrated into the device.
- The unit does not operate normally or its performance has changed.
- The device has been dropped or the housing is damaged.
Disconnect the mains plug and do not continue to operate the device. Do not attempt to repair or open the unit yourself. Contact a trained technician or contact the seller or FeinTech Service
Disposal of the device after use
Old appliances are not worthless waste, but contain valuable raw materials. At
the end of its life, this product should not be disposed of with normal
household waste, but should be taken to a collection point for the recycling
of electrical and electronic equipment. Contact your local authority for
information about recycling points.
CE Declaration of Conformity
This product complies with EU directives and may only be used in conjunction
with shielded cables. We, Spreewald Kommunikationstechnik GmbH, hereby declare
that this device complies with the Low Voltage Directive 2014/35/EU, the EMC
Directive 2014/30/EU, the RoHS Directive 2011/65/EU and the Commission
Regulation (EU) 2019/1782. You can obtain the formal declaration of conformity
at https://feintech.eu/ce or on request.
- Power supply model identifier TY0500100E1mn
- Input voltage 100–240 V
- Input AC frequency 50/60 Hz
- Output voltage 5 V DC
- Output current 1.0 A
- Output power 5.0 W
- Average active efficiency 74.65 %
- No-load power consumption 0.1 W
Troubleshooting
Problem | Cause | Solution |
---|
No picture, no sound / drop-
outs
| HDMI cable too long| use shorter HDMI cables < 5 m
No picture, no sound| wrong HDMI input selected| press button to switch to
correct HDMI input
No picture, no sound| wrong format selected or HDMI
handshake failed
| briefly unplug all units from the
mains and restart
No picture, no sound on Full-
HD Display
| Player outputs 4k, default EDID
mode 4K 60Hz selected
| connect TV to output 1 and
select EDID Copy mode
No sound on tv| unsupported audio format
selected
| Connect TV to output 1 and
select EDID Copy mode
No sound on tv| unsupported audio format
selected
| Listen to sound only via sound
system (e.g. for DTS, HD audio)
No sound on soundbar| Output connected to HDMI-
ARC (output)
| use regular HDMI Input on
soundbar (if available)
No sound on soundbar / Sonos| Soundbar has no regular HDMI
input, only HDMI-ARC
| Operate soundbar at the TV’s
HDMI-ARC connector
No sound on AV-Receiver| unsupported eARC activated| switch off eARC on TV
No picture on Full-HD display with 4k signal| 1080p 50/60Hz resolution not
supported by display, maybe only 1080i or 25Hz| Set lower resolution or
refresh rate on player or connect
Full-HD display to output 1 and
select EDID Copy mode
Incorrect colours on Full-HD
display
| Player outputs Dolby Vision or
HDR10+ feed
| switch off HDR on player
Incorrect contrast / picture too bright or too dark on one display| Different
colour space setting| Set the displays to the same colour space, e.g. set both
to YUV colour space or to RGB
limited
Wrong picture contrast| No usual home cinema player
connected, e.g. PC
| use EDID Copy mode or adjust
display
No 3D video selectable| 4K TV does not support 3D| Connect 3D display to output 1
and select EDID Copy mode
No VRR / Freesync selectable| HDMI 2.0 does not support it| switch off VRR /
Freesync
No 4K 120Hz selecteable| HDMI 2.0 does not support it| select 4K 60Hz
QHD monitor (1440p) displays
only Full-HD (1080p)
| Scaler processes 2160p to
1080p for 4K feed
| connect QHD monitor to output
1 and use EDID COPY mode
References
- FeinTech | Dein Spezialist für Audio, Video & HDMI | Offizieller Shop
- CE Konformitätserklärungen - FeinTech
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>