LED 120cm 60W Explosion Proof Light User Manual
- June 17, 2024
- LED
Table of Contents
Explosion Proof Light
USER MANUAL
WARNING
Before carrying out any manipulation, make sure to disconnect the luminaire
from the power supply. Any incidents in the installation havenit made in
accordance with this installation guide will be the responsibility of the
installer. Replacement or maintenance of any component must be supplied or
recommended by the manufacturer. The light source of this luminaire should be
replaced only by the manufacturer, its service or equivalent qualified person
Explosion Proof Light
WARNING
Connection block included. Installation of the luminaire may require the
intervention of a qualified person.
PHOTOBIOLOGICAL RISK
The luminaire shall be so placed that a prolonged ook at the luminaire don’t
expected at a distance closer to 2,8 meters
- This luminaire is designed to be installed in exteriors and interiors of industrial zones, ships, factories, etc.
- Luminaire configurations are designed to operate at a maximum ambient temperatures of ta 35°C.
- Luminaire is designed to be mounted horizontally with the LEDs facing downwards as shown in the image.
APPLICATION
Applied to oil fields, oil refineries, offshore oil platform, power plants, gas stations, oil tanks, wharf, tunnel, pumping station, substation, the military base,etc. Zone and Zone 2 Hazardous Locations, Zone 21, Zone 22 and Il A, 1IB, IIC explosive gas and dust atmosphere.
CONFORMITY WITH STANDARDS
The product complies with the ATEX Directive
94/9 ECand standards:
-EN 60079-0: 2013
-EN 60079-7: 2015
-EN 6007918: 2015
-EN 60079-31:2014
The productis developed, manufactured and tested according to EN/ISO 9001:
2015
The product is in compliance with:
-LVD Directive 2014/35 EU
-EMC Directive 2014/30 EU
-RoHS Directive 2011/65 EU
SPECIFICATIONS
Electrical Power (W): From 20W to 75W/
Voltage (V): 220-240V
Power Factor: 095
IP protection: 66
IK protection: 10
Electrical power class: Class 1
N.W/ G.W: Dimensions ( LxWxH ):
0.6M 20W: 3.3Kg / 4.0Kg&59911469mm
0.6M 40W: 3.3Kg / 4.0Kg&S59911469mm
1.2M 40W: 4.2Kg / 5.0Kg&1199%11469mm
1.2M 60W: 4.2Kg / 5.0Kg&1199%11469mm
1.2M 75W: 4.2Kg / 5.0Kg&1199%114*69mm
EXPLOSION PROTECTION
II 2G Exeb mb 1ICT6 Gb
II 2D Exth IIIC T(110°C) Db
INSTALLATION
-
UNPACKAGING
Unpack the luminaire and check that any part hasn’t been damaged. If it finds any damage, keep the luminaire back in the packaging and contact us. -
HANDLING
If the luminaire is handled incorrectly after removal from the packaging, damage may occur. Don’t knock or stack luminaires after removing them from the packa- ging. -
INSTALLATION
A ) Reccesed mounting:
• Install the ceiling bracket on the lamp body and tighten the screws
• Fix the lamp to the wall or ceiling
• If the installation is correct, the uminaire shoula be fixed as the image below
B) Bracket mounting:
WARNING
For this type of installation you will need a bracket kit
• Install the rotating bracket on the lamp body and tighten the screws
• Fix the lamp to the wall or ceiling
• Fix the lamp and then connect wire
-
WIRING
Check that the supply voltage is correct and connect the power cables of the luminaire following the color code as shown in the indications.
WARNING
The flexible cable or outside cord of this luminaire can’t be replaced. If the cable is damage, the luminaire must be destroyed.
Connections Cable colour:| Supply type:
---|---
Brown/Black| Phase
Yellow&Green/Green| Ground
Blue/White| Neutral
• Make sure that the cable connection is correct. If the installation is
correct, the luminaire should be fixed as in the image below
- MAINTENANCE / CLEANING
To maintain the high efficiency of the high bay, it needs occasional cleaning on the lens surface. Use a soap with neutral pH with a clotch to clean and dry it.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>