FeinTech VAX01203 HDMI 2.0 HD-Audio Extractor Instruction Manual
- June 4, 2024
- FeinTech
Table of Contents
VAX01203 HDMI 2.0 HD-Audio Extractor
supports 4K@60Hz YUV 4:4:4, HDR, HDCP 2.2, CEC
Instruction Manual
VAX01203 HDMI 2.0 HD-Audio Extractor
Dear customer,
Thank you for purchasing this high-quality product. Please read these
instructions before installation to ensure optimum use and safety. Please keep
this manual for future reference.
Functions:
- Sends the sound of an Ultra-HD HDMI signal source via HDMI to an AV receiver, soundbar, or headphones, with support for 7.1 sound formats such as Dolby Atmos and DTS:X
- Basically, the same audio-video format is sent to all outputs
- Loss-free passthrough of an HDMI signal up to 18 Gbps / Ultra-HD HDR Dolby Vision
EDID switch
Via EDID (Extended Display Identification Data), a connected TV, AV receiver, or projector signals its capabilities (including supported video resolution and audio format). Then the HDMI source outputs the best-supported signal format. With the HD Audio Extractor, you can choose which audio format is signaled to the source and thereby output.
- If you want to use the audio jack, set the EDID mode switch to “2.0”. If you do not hear anything, select stereo or the stereo audio track on your source.
- If you want to use the optical connection, it is best to select the EDID mode “5.1”. If you do not hear anything, select Dolby Digital Bitstream on your external player, not Dolby Digital Plus, not Automatic, and not the “best available sound”. DTS 5.1 sound can also be transmitted.
- All audio formats are supported via HDMI. Select the EDID mode “7.1” to transmit the best available audio format, e.g. Dolby Atmos. The internal TV speakers may then remain mute.
Connections & Controls
-
Power supply connection 5 V hollow plug 3.2 mm Ø
-
EDID mode switch for adapting the maximum audio format to the sound system:
2.0: analog stereo (output possible via all outputs)
5.1: DTS/ Dolby Digital 5.1, (5.1 output only via HDMI and optical / Toslink)
7.1: DTS-HD, Dolby Digital Plus, Dolby TrueHD / Atmos, LPCM 5.1/7.1 (HD audio formats, multichannel PCM, and Dolby Digital Plus are only possible via HDMI) -
Input for HDMI source/player
-
Output for connection of TV, monitor, or video projector
-
OPT: Optical audio digital output SPDIF Toslink
-
AUX: Analogue audio output 3.5 mm jack, only active with stereo sound
-
HDMI output for connection to an HDMI input of the sound system delivers a video signal up to a maximum of 1080p as well as audio (4K 60Hz are scaled to 1080p 60Hz)
-
Power LED lights up when the power supply is active
-
Signal LED, lights up when an input signal is detected
The HDMI HD Audio Extractor has no on/off switch and thus does not require a
remote control.
The unit can also be powered from a USB device socket instead of from the
power supply unit.
This allows the HDMI HD Audio Extractor to be started together with the TV or
PC, for example. An adapter cable DC hollow plug to USB is included.
Note: An HDMI-ARC connection of a soundbar is an HDMI output with an
audio return channel. This connector is not input and is not suitable for
connecting the HDMI HD Audio Extractor.
HDMI-only audio output
A downscaled is automatically activated at this output if the source device
outputs an Ultra HD signal. The original 2160p 50/60Hz signal is downscaled to
1080p 50/60Hz. This makes the signal compatible with an older AV receiver with
HDMI 1.3 interface. The signal at the HDMI TV output is not affected.
Note: An input signal with 1440p is not scaled. This format might not be
processed by all AV receivers.
Installation and operation
-
Connect the HDMI signal source (e.g. Bluray player) to the HDMI input.
-
Connect an HDMI display (e.g. TV, monitor, or video projector) to the HDMI TV output.
Connect an AV receiver or sound bar to HDMI Audio output. -
You can use the audio outputs digital optical and 3.5 mm jack alternatively or additionally.
-
Connect the power supply unit to the HDMI HD Audio Extractor and plug it into a power socket.
Or use the USB adapter cable for the power supply. Then switch on the TV and sound system, then the media player.
Caution: Make sure that the HDMI plug contacts are not dirty or damaged when connecting or disconnecting the HDMI cables. Make connections without power and switch on the devices only after connecting them. Please also pay attention to the good quality of the HDMI cables. Good cables usually have a large diameter. The HDMI cable length shall not exceed 5 m for 4K unless you use special active cables.
- Please do not cover the housing or install the device to avoid overheating.
- Keep away from heat sources, water and moisture.
- Do not place heavy objects on the device or the connection cables.
- Do not open or drill holes in the housing.
- Use only the supplied power adaptor or ensure identical performance data when replacing.
- Use only a soft, dry cloth to clean the surface of the unit. Please do not use aggressive cleaning agents, gasoline, or the like.
- If the unit will not be used for a longer period of time, please unplug it from the mains.
Service
The device must be checked by qualified personnel in the following cases:
- Objects or liquids have penetrated the device.
- The unit is not operating normally or performance has changed.
- The unit has been dropped or the housing is damaged.
Do not attempt to repair or open the unit yourself. Contact trained specialist personnel or fintech
CE Declaration of Conformity
This product complies with EU directives and may only be used in conjunction
with shielded cables. We, Spreewald Kommunikationstechnik GmbH, hereby declare
that this device complies with the Low Voltage Directive 2014/35/EU, the EMC
Directive 2014/30/EU, the Commission Regulation (EU) 2019/1782 and the RoHS
Directive 2011/65/EU. You can obtain the formal declaration of conformity at
https://feintech.eu/ce or on request.
Information according to the COMMISSION REGULATION (EU)
2019/1782
Spreewald Kommunikationstechnik GmbH
HR B 1107 Cottbus
Radensdorfer Hauptstr. 45 a, 15907 Lübben (Spreewald), Germany
Power supply model identifier | KDP-AB050100U |
---|---|
Manufacturer | Dongguan Kingdrive Industry Co., Ltd. |
1-2 Floor, Building A, No. 11, Headquarters 2 Road, Songshan Lake, Dongguan
City, Guangdong, China
Input voltage| 100-240 V
Input AC frequency| 50/60 Hz
Output voltage| 5 V DC
Output current| 1.0 A
Output power| 5.0 W
Average active efficiency| 74.%
No-load power consumption| 0.055 W
Connection scheme (all units receive the same audio format, stereo, and surround sound cannot be mixed)
Specification
Operation Temperature | Betriebs-Temperaturbereich | -5° C bis +40° C |
---|---|---|
Operation humidity | Betriebs-Luftfeuchtigkeit | 10 – 90 % RH (nicht |
kondensierend)
HDMI compliance| HDMI-Version| HDMI 2.0b
Signal input| Signal-Eingang| 1 x HDMI
Copy protection| Unterstutzter Kopierschutz| HDCP 2.2 & 1.4
Data rate| Daten-Ubertragungsrate| 18 Gbps (Maximum)
Data bandwidth| Maximale Bandbreite| 600 MHz
Supported video resolution| Untersilitzte Videoformate| 2160p max. 60Hz, 1440p
max. 120Hz, 1080 i/p, 720i/p max. 120Hz
Signal outputs| Signal-Ausgang| 2 x HDMI, 1 x SPDIF Toslink, 1 x 3,5 mm stereo
Colour space| Farbraum| RGB, YCbCr 4:4:4, 4:2:2; 4:2:0
Supported color depth| Unterstutzte Farbformate| 3 x 8 Bit – 12 Bit
HDR| HDR (High Dynamic Range)| HDR10, HLG-HDR, Dolby Vision
Video format HDMI TV out| Video Format HDMI TV| 2160p @ 60Hz or lower
Video format HDMI Audio| Video Format HDMI Audio| 1080p (1440p) or lower
ARC (Audio Return Channel)| ARC-Unterstiitzung| no
Audio formats ARC, SPDIF
Toslink| Audio Formate ARC, SPDIF Toslink| AC3 (Dolby Digital), DTS, LPCM 2.0,
max. 192 kHz
Audio format 3.5 mm jack| Audio Format 3,5mm Klinke| Analog stereo
Audio formats HDMI| Audio Formate via HDMI| DTS-HD, Dolby True-HD (incl.
Atmos), Dolby Digital Plus, AC3 (Dolby Digital), DTS, DSD, LPCM 2.0 – 7.1
HDMI-CE control| HDMI-CEC Steuerung| yes, source => TV
HDMI cable length| HDMI Kabellange| < 5 m (4K HDR), < 10 m 1080p
Power consumption| Leistungsaufnahme| < 1 W (max. 180 mA)
Size (WxLxH)| Abmessungen (BxLxH)| 122 x 57 x 20 mm
Net weight| Nettogewicht| 165 g
FeinTech® is a registered trademark of Spreewald Kommunikationstechnik
GmbH
Radensdorfer Hauptstr. 45 a
• 15907 Lübben (Spreewald)
• Germany
info@feintech.eu
• +49 3546 239 88 55
• WEEE-Reg.-Nr. DE15618234
www.feintech.eu
•facebook.com/feintech
References
- FeinTech | Dein Spezialist für Audio, Video & HDMI | Offizieller Shop
- CE Konformitätserklärungen - FeinTech
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>